Refine
Document Type
- Article (reviewed) (8) (remove)
Language
- English (8)
Is part of the Bibliography
- yes (8) (remove)
Keywords
- copper oxide (1)
- diode modeling (1)
- indium oxide (1)
- nickel oxide (1)
- oxide electronics (1)
- pn-diode (1)
- printed electronics (1)
Institute
Open Access
- Open Access (5)
- Closed Access (3)
- Gold (1)
Printed systems spark immense interest in industry, and for several parts such as solar cells or radio frequency identification antennas, printed products are already available on the market. This has led to intense research; however, printed field-effect transistors (FETs) and logics derived thereof still have not been sufficiently developed to be adapted by industry. Among others, one of the reasons for this is the lack of control of the threshold voltage during production. In this work, we show an approach to adjust the threshold voltage (Vth) in printed electrolyte-gated FETs (EGFETs) with high accuracy by doping indium-oxide semiconducting channels with chromium. Despite high doping concentrations achieved by a wet chemical process during precursor ink preparation, good on/off-ratios of more than five orders of magnitude could be demonstrated. The synthesis process is simple, inexpensive, and easily scalable and leads to depletion-mode EGFETs, which are fully functional at operation potentials below 2 V and allows us to increase Vth by approximately 0.5 V.
Silicon (Si) has turned out to be a promising active material for next‐generation lithium‐ion battery anodes. Nevertheless, the issues known from Si as electrode material (pulverization effects, volume change etc.) are impeding the development of Si anodes to reach market maturity. In this study, we are investigating a possible application of Si anodes in low‐power printed electronic applications. Tailored Si inks are produced and the impact of carbon coating on the printability and their electrochemical behavior as printed Si anodes is investigated. The printed Si anodes contain active material loadings that are practical for powering printed electronic devices, like electrolyte gated transistors, and are able to show high capacity retentions. A capacity of 1754 mAh/gSi is achieved for a printed Si anode after 100 cycles. Additionally, the direct applicability of the printed Si anodes is shown by successfully powering an ink‐jet printed transistor.
Electrolyte-gated transistors (EGTs) represent an interesting alternative to conventional dielectric-gating to reduce the required high supply voltage for printed electronic applications. Here, a type of ink-jet printable ion-gel is introduced and optimized to fabricate a chemically crosslinked ion-gel by self-assembled gelation, without additional crosslinking processes, e.g., UV-curing. For the self-assembled gelation, poly(vinyl alcohol) and poly(ethylene-alt-maleic anhydride) are used as the polymer backbone and chemical crosslinker, respectively, and 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIM][OTf]) is utilized as an ionic species to ensure ionic conductivity. The as-synthesized ion-gel exhibits an ionic conductivity of ≈5 mS cm−1 and an effective capacitance of 5.4 µF cm−2 at 1 Hz. The ion-gel is successfully employed in EGTs with an indium oxide (In2O3) channel, which shows on/off-ratios of up to 1.3 × 106 and a subthreshold swing of 80.62 mV dec−1.
Fully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates
(2020)
Printed and flexible metal‐oxide transistor technology has recently demonstrated great promise due to its high performance and robust mechanical stability. Herein, fully printed inverter structures using electrolyte‐gated oxide transistors on a flexible polyimide (PI) substrate are discussed in detail. Conductive graphene ink is printed as the passive structures and interconnects. The additive printed transistors on PI substrates show an on/off ratio of 106 and show mobilities similar to the state‐of‐the‐art printed transistors on rigid substrates. Printed meander structures of graphene are used as pull‐up resistances in a transistor–resistor logic to create fully printed inverters. The printed and flexible inverters show a signal gain of 3.5 and a propagation delay of 30 ms. These printed inverters are able to withstand a tensile strain of 1.5% following more than 200 cycles of mechanical bending. The stability of the electrical direct current (DC) properties has been observed over a period of 5 weeks. These oxide transistor‐based fully printed inverters are relevant for digital printing methods which could be implemented into roll‐to‐roll processes.
Oxide semiconductors have the potential to increase the performance of inkjet printed microelectronic devices such as field-effect transistors (FETs), due to their high electron mobilities. Typical metal oxides are n-type semiconductors, while p-type oxides, although realizable, exhibit lower carriermobilities. Therefore, the circuit design based on oxide semiconductors is mostly in n-type logic only. Here we present an inkjet printed pn-diode based on p- and n-type oxide semiconductors.Copper oxide or nickel oxide is used as p-typesemiconductor whereas n-typesemiconductor is realized with indium oxide. Themeasurements show that the pn-diodes operate in the voltage window typical for printed electronics and the emission coefficient is 1.505 and 2.199 for the copper oxide based and nickel oxidebased pn-diode, respectively.Furthermore, a pn-diode model is developed and integrable into a circuit simulator.
Development of Fully Printed Oxide Field-Effect Transistors using Graphene Passive Structures
(2019)
During the past decade to the present time, the topic of printed electronics has gained a lot of attention for their potential use in a number of practical applications, including biosensors, photovoltaic devices, RFIDs, flexible displays, large-area circuits, and so on. To fully realize printed electronic components and devices, effective techniques for the printing of passive structures and electrically and chemically compatible materials in the printed devices need to be developed first. The opportunity of using electrically conducting graphene inks will enable the integration of passive structures into active devices, as for example, printed electrolyte-gated transistors (EGTs). Accordingly, in this study, we present the parametric results obtained on fully printed electrolyte-gated transistors having graphene as the passive electrodes, an inorganic oxide semiconductor as the active channel, and a composite solid polymer electrolyte (CSPE) as the gate insulating material. This configuration offers high chemical and electrical stability while at the same time allowing EGT operation at low potentials, implying the distinct advantage of operation at low input voltages. The printed in-plane EGTs we developed exhibit excellent performance with device mobility up to 16 cm2 V–1 s–1, an ION/IOFF ratio of 105, and a subthreshold slope of 120 mV dec–1.
In this report, we have studied field-effect transistors (FETs) using low-density alumina for electrolytic gating. Device layers have been prepared starting from the structured ITO glasses by printing the In 2 O 3 channels, low-temperature atomic layer deposition (ALD) of alumina (Al 2 O 3 ), and printing graphene top gates. The transistor performance could be deliberately changed by alternating the ambient humidity; furthermore, ID,ON/ID,OFF-ratios of up to seven orders of magnitude and threshold voltages between 0.66 and 0.43 V, decreasing with an increasing relative humidity between 40% and 90%, could be achieved. In contrast to the common usage of Al 2 O 3 as the dielectric in the FETs, our devices show electrolyte-typegating behavior. This is a result from the formation of protons on the Al 2 O 3 surfaces at higher humidities. Due to the very high local capacitances of the Helmholtz double layers at the channel surfaces, the operation voltage can be as low as 1 V. At low humidities (≤30%), the solid electrolyte dries out and the performance breaks down; however, it can fully reversibly be regained upon a humidity increase. Using ALD-derived alumina as solid electrolyte gating material, thus, allows low-voltage operation and provides a chemically stable gating material while maintaining low process temperatures. However, it has proven to be highly humidity-dependent in its performance.
In this study, a facile method to fabricate a cohesive ion‐gel based gate insulator for electrolyte‐gated transistors is introduced. The adhesive and flexible ion‐gel can be laminated easily on the semiconducting channel and electrode manually by hand. The ion‐gel is synthesized by a straightforward technique without complex procedures and shows a remarkable ionic conductivity of 4.8 mS cm−1 at room temperature. When used as a gate insulator in electrolyte‐gated transistors (EGTs), an on/off current ratio of 2.24×104 and a subthreshold swing of 117 mV dec−1 can be achieved. This performance is roughly equivalent to that of ink drop‐casted ion‐gels in electrolyte‐gated transistors, indicating that the film‐attachment method might represent a valuable alternative to ink drop‐casting for the fabrication of gate insulators.