Refine
Year of publication
- 2013 (18) (remove)
Document Type
- Article (reviewed) (18) (remove)
Has Fulltext
- no (18)
Is part of the Bibliography
- yes (18) (remove)
Keywords
- Dünnschichtchromatographie (3)
- Bürohaus (2)
- Kohlenstoff (2)
- Adsorption (1)
- Benzocain (1)
- Biolumineszenz (1)
- Druck (1)
- Elektrizitätsmarkt (1)
- Energieeffizienz (1)
- Energiewirtschaft (1)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (18) (remove)
Open Access
- Closed Access (9)
- Open Access (3)
Der Einbau von Smart Metern und deren intelligente Vernetzung in Richtung eines Smart Grid wird Stromverbrauchsmuster bis in die Haushalte hinein verändern. Über die technisch geprägte Diskussion um die Komponenten dafür darf deshalb keinesfalls die Einbeziehung der Gesellschaft in den anstehenden Wandel vergessen werden. Transparenz bei den Kosten, die Förderung von Vertrauen insbesondere in die Datenschutzstandards und eine verständliche Aufklärungsarbeit sind Schlüssel für den notwendigen Dialog zwischen Energieversorgern, Politik und Bürgern.
We present a video-densitometric quantification method in combination with diode-array quantification for the methyl-, ethyl-, propyl-, and butylparaben in cosmetics. These parabens were separated on cyanopropyl bonded plates using water-acetonitrile-dioxane-ethanol-NH3 (25%) (8:2:1:1:0.05, v/v) as mobile phase. The quantification is based on UV-measurements at 255 nm and a bioeffectively-linked analysis using Vibrio fischeri bacteria. Within 5 min, a Tidas S 700 diode-array scanner (J&M, Aalen, Germany) scans 8 tracks and thus measures in total 5600 spectra in the wavelengths range from 190 to 1000 nm. The quantification range for all these parabens is from 20 to 400 ng per band, measured at 255 nm. In the V. fischeri assay a CCD-camera registers the white light of the light-emitting bacteria within 10 min. All parabens effectively suppress the bacterial light emission which can be used for quantifying within a linear range from 100 to 400 ng. Measurements were carried out using a 16-bit MicroChemi chemiluminescence system (biostep GmbH, Jahnsdorf, Germany), using a CCD camera with 4.19 megapixels. The range of linearity is achieved because the extended Kubelka-Munk expression was used for data transformation. The separation method is inexpensive, fast, and reliable.
Der Endkundenvertrieb ist für die Bewahrung und Weiterentwicklung des Kundenstamms eines Energieversorgers essenziell. Doch um knappe Mittel im Vertrieb möglichst wirkungsvoll einsetzen zu können, wird Wissen darüber benötigt, wie sich die durchschnittlich erzielbaren Strompreise und die zu erwartende Kundenbindungsdauer zwischen verschiedenen Vertriebskanälen unterscheiden. Leitet man anhand dieser Informationen den Wert eines Kunden je Vertriebskanal ab, lässt sich treffsicherer über einzusetzende Marketing-Budgets entscheiden.
Unter dem europäischen Programm Intelligent Energy for Europe (IEE) fanden sich acht europäische Partner zusammen, um im Rahmen des Projektes ThermCo Lüftungs‐ und Kühlenergiekonzepte für Nichtwohngebäude mit niedrigem Energieeinsatz im Hinblick auf die Energieeffizienz und den thermischen Raumkomfort zu bewerten (siehe Teil 1 dieser Veröffentlichung in Bauphysik 34 (2012), Heft 6. Mit Hilfe einer Simulationsstudie für ein typisches Bürogebäude wird das Potenzial unterschiedlicher Lüftungs‐ und Kühlstrategien unter Berücksichtigung von Energieeffizienz und Raumkomfort für verschiedene europäische Klimazonen bewertet. Die Ergebnisse weisen eine hohe Wirksamkeit von Nachtlüftungskonzepten im nord‐europäischen Sommerklima mit verhältnismäßig niedrigen Außentemperaturen nach. Im mitteleuropäischen Sommerklima bietet das Erdreich ein ausreichend niedriges Temperaturniveau für den effizienten Einsatz von wassergeführten Flächentemperiersystemen. Im südeuropäischen Sommerklima kann eine aktive Kühlung über Luft die hohen und schnell fluktuierenden Kühllasten effizient abführen.
Raman spectra from three different binary gasoline-ethanol blends (with ratios 95:5, 90:10, and 85:15) have been obtained by using a low-cost, frequency precise Fourier-transform Raman spectrometer (FT-Raman) prototype. The spectral information is presented in the range of 0 to 3500 cm-1 with a resolution of 1.66 cm-1, which is greater than the required for most liquid and solid chemical samples. This set-up delivers spectral information about the sample with a reduced spectral deviation compared to theoretical values (less than 0.4 cm-1 without compensation for instrumental response). The robust and highly fexible FT-Raman prototype presented for the spectral analysis, consisting mainly of a Michelson interferometer and a self-designed photon counter, is able to deliver high resolution and frequency precise Raman spectra from the gasoline-ethanol blends comparable to the obtained by using commercial devices. This FT-Raman set-up does not need additional complex hardware or software control and relies on re-sampling and interpolation algorithms. The qualitative spectral information obtained has been used to calculate the proportion of gasoline and ethanol present in the used chemical samples without using extra calibrations methods or chemical markers.
In this paper, an unconditionally stable algorithm for the numerical integration and finite-element implementation of a class of pressure dependent plasticity models with nonlinear isotropic and kinematic hardening is presented. Existing algorithms are improved in the sense that the number of equations to be solved iteratively is significantly reduced. This is achieved by exploitation of the structure of Armstrong-Frederik-type kinematic hardening laws. The consistent material tangent is derived analytically and compared to the numerically computed tangent in order to validate the implementation. The performance of the new algorithm is compared to an existing one that does not consider the possibility of reducing the number of unknowns to be iterated. The algorithm is used to implement a time and temperature dependent cast iron plasticity model, which is based on the pressure dependent Gurson model, in the finite-element program ABAQUS. The implementation is applied to compute stresses and strains in a large-scale finite-element model of a three cylinder engine block. This computation proofs the applicability of the algorithm in industrial practice that is of interest in applied sciences.