Refine
Year of publication
Document Type
- Conference Proceeding (12)
- Article (reviewed) (6)
- Patent (1)
- Article (unreviewed) (1)
Conference Type
- Konferenzartikel (10)
- Konferenz-Abstract (2)
Language
- English (20) (remove)
Is part of the Bibliography
- yes (20) (remove)
Keywords
- Finite-Elemente-Methode (3)
- Nonlinearity (3)
- Substrates (2)
- Surface Acoustic Waves (2)
- Surface acoustic waves (2)
- Ultraschall (2)
- Acoustical properties (1)
- Akustische Oberflächenwelle (1)
- AlScN (1)
- Crystal structure (1)
Institute
Open Access
- Closed Access (8)
- Closed (6)
- Open Access (4)
- Gold (2)
- Bronze (1)
A simple model is introduced that describes the interaction of surface acoustic waves (SAWs) with a 2D periodic array of objects on the surface that give rise to internal resonances. Such objects may be high-aspect ratio structures like micro-pillars fabricated of a material different from that of the substrate. The model allows for an approximate determination of the band structure for the acoustic modes in such systems. Results are presented for the dependence on structural parameters of a total bandgap in the non-radiative regime of a semi-infinite substrate, and it is shown how the frequency and radiation damping of vibrational modes can be determined that are associated with defects in the periodic 2D array.
High-precision signal processing algorithm to evaluate SAW properties as a function of temperature
(2013)
This paper presents a signal processing algorithm which accurately evaluates the SAW properties of a substrate as functions of temperature. The investigated acoustic properties are group velocity, phase velocity, propagation loss, and coupling coefficient. With several measurements carried out at different temperatures, we obtain the temperature dependency of the SAW properties. The analysis algorithm starts by reading the transfer functions of short and long delay lines. The analysis algorithm determines the center frequency of the delay lines and obtains the delay time difference between the short and long delay lines. The extracted parameters are then used to calculate the acoustic properties of the SAW material. To validate the algorithm, its accuracy is studied by determining the error in the calculating delay time difference, center frequency, and group velocity.
Laser ultrasound was used to determine dispersion curves of surface acoustic waves on a Si (001) surface covered by AlScN films with a scandium content between 0 and 41%. By including off-symmetry directions for wavevectors, all five independent elastic constants of the film were extracted from the measurements. Results for their dependence on the Sc content are presented and compared to corresponding data in the literature, obtained by alternative experimental methods or by ab-initio calculations.
In a SAW device comprises a SAW chip bearing a SAW transducer arranged within a first signal line parasitic signals due to higher harmonics of the operating frequency of the SAW devices are electrically eliminated by compensating means comprising at least one second signal line having means for producing a cancelling signal different in sign or phase to the parasitic signal, or a shunt line to electrically connect the SAW transducer to a back side metallization of the SAW chip.
Recently a P-matrix and COM formalism was presented, which predicts third order intermodulation (IMD3) and triple beat with good accuracy and needs only a single nonlinearity constant. This formalism describes frequency dependence correctly. In this work the dependence of this nonlinearity constant on metalization ratio is investigated for aluminum metalization on LiTaO 3 (YXl)/42°. By comparison to test devices the nonlinearity constant is shown to be largely independent of metalization ratio. The nonlinear effect, however, strongly depends on metalization ratio, which is well described by the model. The linearity of a duplexer is optimized by reduction of metalization ratio and redesign of Tx branch topology.
In this work a set of nonlinear coupled COM equations at interacting frequencies is derived on the basis of nonlinear electro-elasticity. The formalism is presented with the aim of describing intermodulation distortion of third-order (IMD3) and triple beat. The resulting COM equations are translated to the P-matrix formalism, where care is taken to obtain the correct frequency dependence. The scheme depends on two frequency-independent constants for an effective third-order nonlinearity. One of these two constants is negligibly small in the systems considered here. The P-matrix approach is applied to single filters and duplexers on LiTaO 3 (YXl)/42° operating in different frequency ranges. Both IMD3 and triple beat show good agreement with measurement.
The laser ultrasound (LU) technique has been used to determine dispersion curves for surface acoustic waves (SAW) propagating in AlScN/Al2O3 systems. Polar and non-polar Al0.77Sc0.23N thin films were prepared by magnetron sputter epitaxy on Al2O3 substrates and coated with a metal layer. SAW dispersion curves have been measured for various propagation directions on the surface. This is easily achieved in LU measurements since no additional surface structures need to be fabricated, which would be required if elastic properties are determined with the help of SAW resonators. Variation of the propagation direction allows for efficient use of the system’s anisotropy when extracting information on elastic properties. This helps to overcome the complexity caused by a large number of elastic constants in the film material. An analysis of the sensitivity of the SAW phase velocities (with respect to the elastic moduli and their dependence on SAW propagation direction) reveals that the non-polar AlScN films are particularly well suited for the extraction of elastic film properties. Good agreement is found between experiment and theoretical predictions, validating LU as a non-destructive and fast technique for the determination of elastic constants of piezoelectric thin films.
In the framework of electro-elasticity theory and the finite element method (FEM), a model is set up for the computation of quantities in surface acoustic wave (SAW) devices accounting for nonlinear effects. These include second-order and third-order intermodulations, second and third harmonic generation and the influence of electro-acoustic nonlinearity on the frequency characteristics of SAW resonators. The model is based on perturbation theory, and requires input material constants, e.g., the elastic moduli up to fourth order for all materials involved. The model is two-dimensional, corresponding to an infinite aperture, but all three Cartesian components of the displacement and electrical fields are accounted for. The first version of the model pertains to an infinite periodic arrangement of electrodes. It is subsequently generalized to systems with a finite number of electrodes. For the latter version, a recursive algorithm is presented which is related to the cascading scheme of Plessky and Koskela and strongly reduces computation time and memory requirements. The model is applied to TC-SAW systems with copper electrodes buried in an oxide film on a LiNbO3 substrate. Results of computations are presented for the electrical current due to third-order intermodulations and the displacement field associated with the second harmonic and second-order intermodulations, generated by monochromatic input tones. The scope of this review is limited to methodological aspects with the goal to enable calculations of nonlinear quantities in SAW devices on inexpensive and easily accessible computing platforms.