Refine
Year of publication
- 2013 (59) (remove)
Document Type
- Conference Proceeding (59) (remove)
Conference Type
- Konferenzartikel (42)
- Konferenz-Abstract (10)
- Sonstiges (3)
- Konferenz-Poster (2)
- Konferenzband (2)
Keywords
- Energieversorgung (3)
- Herzkrankheit (3)
- Kommunikation (3)
- Konstruktion (3)
- Synchronisierung (3)
- Batterie (2)
- Brennstoffzelle (2)
- Messung (2)
- Mikroelektronik (2)
- Optik (2)
Institute
- Fakultät Elektrotechnik und Informationstechnik (E+I) (bis 03/2019) (43)
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (11)
- INES - Institut für nachhaltige Energiesysteme (6)
- Fakultät Wirtschaft (W) (4)
- Fakultät Medien und Informationswesen (M+I) (bis 21.04.2021) (3)
- IUAS - Institute for Unmanned Aerial Systems (2)
Open Access
- Open Access (32)
- Closed Access (26)
- Bronze (5)
- Closed (1)
Durch eine stetige Preissteigerung der fossilen Energieträger werden auch im Bereich der mobilen Arbeitsmaschinen neben einer hohen Zuverlässig u.a. Forderungen nach steigenden Gesamtwirkungsgraden, mit der hierdurch einhergehenden Energieeffizienz, forciert. Auch bei mobilen Arbeitsmaschinen ist der häufig eingeschränkt zur Verfügung stehende Bauraum für Traktionsantriebe eine Herausforderung. Ziel dieser Veröffentlichung ist ein allgemeingültiger Vergleich verschiedener elektrischer Antriebsarten als Traktionsantrieb für mobile Arbeitsmaschinen.
Network landscape of recent time contains many different network technologies, a wide range of end-devices with a large scale of capabilities and power, and an immense quantity of information and data represented in different formats. Research on 3D imaging, virtual reality and holographic techniques will result in new user interfaces (UI) for mobile devices, will increase their diversity and variety. In this paper software architecture has been proposed to establish device and content format independent communication including 3D imaging and virtual reality data as content. As experimental validation the concept is implemented in collaborative Language Learning Game (LLG), which is a learning tool for language acquisition.
Efficient, low-cost, secure and reliable communication solutions are a major stepping stone for smart metering and smart grid applications. This especially holds true for the so called primary communication or local metrological network (LMN) between a local meter or actuator and a data collector or gateway, where the highest requirements with regard to cost, bandwidth, and energy efficiency have to be taken into consideration. Multiple developments and field tests are going on in this field, however, energy autarkic devices are hardly found, yet. This contribution describes the development of an automatic water meter reading (AWMR) technology based on Wireless M-Bus to provide water utility companies with an automatic remote water meter reading solution. It addresses the special needs of home utilities by providing a remote metering solution independent from the electricity infrastructure, both in terms of data communication and in terms of power supply. For this project, a cost efficient integrated energy harvesting system powered by the available water flow was developed, to enable operation independently of the mains grid, and eliminate the need for battery replacement for near-zero maintenance costs.
Efficient, low-cost, secure and reliable communication solutions are a major stepping stone for smart metering and smart grid applications. This especially holds true for the so called primary communication or local metrological network (LMN) between a local meter or actuator and a data collector or gateway, where the highest requirements with regard to cost, bandwidth, and energy efficiency have to be taken into consideration. Multiple developments and field tests are going on in this field, however, energy autarkic devices are hardly found, yet.
A highly scalable IEEE802.11p communication and localization subsystem for autonomous urban driving
(2013)
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed for the support of highly autonomous driving. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. Thus it is mainly targeted for the support of traffic safety applications in intra-urban scenarios. This contribution describes the Ko-TAG part of the overall initiative, which develops a subsystem to improve the real-time characteristics of IEEE802.11p needed for precise time of flight real-time localization. In doing this, it still fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. Test results are shown in the last part of the paper.
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed and its benefit for traffic safety applications is evaluated. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. The Ko-TAG proposal enriches the current IEEE802.11p real-time characteristics needed for precise time-of-flight real-time localization. This contribution describes the development of a subsystem, which extends the functionality of IEEE802.11p and fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. The next step will be field measurements to verify the simulation results.
The communication between objects, i.e. between cars (car-2-car, C2C), between cars and infrastructure (car-2-infrastructure, C2I) and between cars and vulnerable road users (car-2-VRU, C2VRU) is a major stepping stone towards traffic applications to enable efficient and safe traffic flow. However, these applications pose very high requirements to the communication protocols, which go beyond the capabilities of an available standardized solution.
This contribution shows how iterative design processes can help to fulfill these requirements, while re-using a maximum of elements from one level to the next and thus avoiding unrealistic overhead. In especially, the added value of simulation and emulation in this iterative process is elaborated.
The communication technologies for automatic meter reading (smart metering) and for energy production and distribution networks (smart grid) have the potential to be one of the first really highly scaled machine-to-machine-M2M-applications. During the last years, two very promising developments around the wireless part of the smart grid communication were initialized, which possibly could have an impact on the network architectures and the markets far beyond Germany and far beyond energy automation. Besides the specification of the OMS Group of a security extension to the Wireless M-Bus protocol (EN13757-4), the German Federal Office for Information Security (Bundesamt für Sicherheit in der Informationstechnik, BSI) has designed a Protection Profile (PP) and a Technical Directive (TR) for the communication unit of an intelligent measurement system (Smart Meter Gateway), which were released in March 2013. This design uses state of the art technologies and prescribes their implementation in real-life systems. At first, the proposed paper will present the most important characteristics of this architecture. It will then give an insight into the implementation of the OMS security protocols, which imply the usage of a mutually authenticated SSL protocol also in the Local Metrological Network. This is achieved with the help of an additional Authentication and Fragmentation Layer (AFL). This secure communication will be terminated in a BSI conformant secure smart meter gateway, which is developed in a different project and described in the second step. Finally, the contribution will discuss the integration of such a metering network into an overall telecommunication network and PKI infrastructure.
Automatic Meter Reading (AMR) is a major enabler for the upcoming smart grid. Potentially, it will be one of the first really large-scale M2M-communication solutions for sensor applications.
To date, the definition of the standardized communication stacks for Local Metrological Network (LMN) in AMR is still ongoing. This holds true both for ZigBee Smart Energy Profile and for Wireless M-Bus according to EN 13757. During this process, there is the necessity for flexible, albeit optimized solutions, which support the different existing and upcoming versions of the communication protocols. In the case of Wireless M-Bus, the major contender for European and possibly Asian installations, this is valid not only for the different operation modes (C-, N-, P-, Q-, R-, S-, and T-modes), which work in different frequencies (i.e. 868 MHz, 433 MHz, and 169 MHz) but also for the application layer, where additional bodies, like EN137575, Open Metering System (OMS) Group, or national bodies follow their approaches.
This contribution describes requirements, design techniques and experiences from the development of highly efficient Wireless M-Bus protocol stacks with support of good flexibility and portability between microcontroller platforms and RF-transceivers. The presented approach is not limited to the use of modern software engineering design processes, as such, but also includes essential additional features like testing or simulation, as well as tools for commissioning and monitoring.