Refine
Year of publication
Document Type
- Conference Proceeding (19)
- Article (reviewed) (17)
- Article (unreviewed) (4)
- Patent (2)
- Part of a Book (1)
Conference Type
- Konferenzartikel (17)
- Konferenz-Abstract (2)
Is part of the Bibliography
- yes (43)
Keywords
- Nonlinearity (4)
- Ultraschall (4)
- Finite-Elemente-Methode (3)
- Surface acoustic waves (3)
- Wedge waves (3)
- Akustik (2)
- Finite element method (2)
- Keilwelle (2)
- Oberfläche (2)
- Schallwelle (2)
Institute
Open Access
- Closed Access (19)
- Closed (11)
- Open Access (7)
- Gold (2)
- Bronze (1)
A Nonlinear FEM Model to Calculate Third-Order Harmonic and Intermodulation in TC-SAW Devices
(2018)
Nonlinearities in Temperature Compensated SAW (TC-SAW) devices in the 2 GHz range are investigated using a nonlinear finite element model by simultaneously considering both third-order intermodulation distortion (IMD3)and third harmonic (H3). In the employed perturbation approach, different contributions to the total H3, the direct and indirect contribution, are discussed. H3 and IMD3 measurements were fitted simultaneously using scaling factors for SiO 2 film and Cu electrode nonlinear material tensors in TC-SAW devices. We employ a P-Matrix simulation as intermediate step: Firstly, measurement and nonlinear P-Matrix calculations for finite devices are compared and coefficients of the P-Matrix simulation are determined. The nonlinear tensor data of the different materials involved in periodic nonlinear finite element method (FEM) computations are optimized to fit periodic P-Matrix calculations by introducing scaling factors. Thus, the contribution of different materials to the nonlinear behavior of TC-SAW devices is obtained and the role of materials is discussed.
The growing complexity in RF front-ends, which support carrier aggregation and a growing number of frequency bands, leads to tightened nonlinearity requirements in all sub-components. The generation of third order intermodulation products (IMD3) are typical problems caused by the non-linearity of SAW devices. In the present work, we investigate temperature compensating (TC) SAW devices on Lithium Niobate-rot128YX. An accurate FEM simulation model [1] is employed, which allows to better understand the origin of nonlinearities in such acoustic devices.
Nonlinearity can give rise to intermodulation distortions in surface acoustic wave (SAW) devices operating at high input power levels. To understand such undesired effects, a finite element method (FEM) simulation model in combination with a perturbation theory is applied to find out the role of different materials and higher order nonlinear tensor data for the nonlinearities in such acoustic devices. At high power, the SAW devices containing metal, piezoelectric substrate, and temperature compensating (TC) layers are subject to complicated geometrical, material, and other nonlinearities. In this paper, third-order nonlinearities in TC-SAW devices are investigated. The materials used are LiNbO 3 -rot128YX as the substrate and copper electrodes covered with a SiO 2 film as the TC layer. An effective nonlinearity constant for a given system is determined by comparison of nonlinear P-matrix simulations to third-order intermodulation measurements of test filters in a first step. By employing these constants from different systems, i.e., different metallization ratios, in nonlinear periodic P-matrix simulations, a direct comparison to nonlinear periodic FEM-simulations yields scaling factors for the materials used. Thus, the contribution of the different materials to the nonlinear behavior of TC-SAW devices is obtained and the role of metal electrodes, substrate, and TC film are discussed in detail.
In the present work, nonlinearities in temperature compensating (TC) SAW devices are investigated. The materials used are LiNbO₃-rot128YX as the substrate and Copper electrodes covered with a SiO₂-layer as the compensating layer. In order to understand the role of these materials for the nonlinearities in such acoustic devices, a FEM simulation model in combination with a perturbation approach is applied. The nonlinear tensor data of the different materials involved in TC-SAW devices have been taken from literature, but were partially modified to fit experimental data by introducing scaling factors. An effective nonlinearity constant is determined by comparison of nonlinear P-matrix simulations to IMD3 measurements of test filters. By employing these constants in nonlinear periodic P-matrix simulations a direct comparison to nonlinear periodic FEM-simulations yields the scaling factors for the material used. Thus, the contribution of different materials to the nonlinear behavior of TC-SAW devices is obtained and the role of metal electrodes is discussed in detail.
This work focuses on the dependencies between typical design parameters of surface acoustic wave (SAW) resonators and the nonlinear emitted signals of second and third order. The parameters metalization ratio and pitch are used as examples, but the approach can be extended to other design parameters as well. It is shown, that the interaction between the nonlinear current generation and the linear admittance is defining the measured nonlinear power signals. It is also discussed, that changes in linear properties get more pronounced in nonlinear responses. Therefore, slight effects on linear parameters will have significant influence on the observed nonlinearity.
Increasing power density causes increased self-generation of harmonics and intermodulation. As this leads to violations of the strict linearity requirements, especially for carrier aggregation (CA), the nonlinearity must be considered in the design process of RF devices. This raises the demand of accurate simulation models. Linear and nonlinear P-Matrix/COM models are used during the design due to their fast simulation times and accurate results. However, the finite element method (FEM) is useful to get a deeper insight in the device's nonlinearities, as the total field distributions can be visualized. The FE method requires complete sets of material tensors, which are unknown for most relevant materials in nonlinear micro-acoustics. In this work, we perform nonlinear FEM simulations, which allow the calculation of nonlinear field distributions of a lithium tantalate based layered SAW system up to third order. We aim at achieving good correspondence to measured data and determine the contributions of each material layer to the nonlinear signals. Therefore, we use approximations circumventing the issue of limited higher order tensor data. Experimental data for the third order nonlinearity is shown to validate the presented approach.
In this work the nonlinear behavior of layered surface acoustic wave (SAW) resonators is studied with the help of finite element (FE) computations. The full calculations depend strongly on the availability of accurate tensor data. While there are accurate material data for linear computations, the complete sets of higher-order material constants, needed for nonlinear simulations, are still not available for relevant materials. To overcome this problem, scaling factors were used for each available nonlinear tensor. The approach here considers piezoelectricity, dielectricity, electrostriction, and elasticity constants up to the fourth order. These factors act as a phenomenological estimate for incomplete tensor data. Since no set of fourth-order material constants for LiTaO3 is available, an isotropic approximation for the fourth-order elastic constants was applied. As a result, it was found that the fourth-order elastic tensor is dominated by one-fourth order Lamé constant. With the help of the FE model, derived in two different, but equivalent ways, we investigate the nonlinear behavior of a SAW resonator with a layered material stack. The focus was set to third-order nonlinearity. Accordingly, the modeling approach is validated using measurements of third-order effects in test resonators. In addition, the acoustic field distribution is analyzed.
Existing ultrasonic stress evaluation methods utilize the acoustoelastic effect for bulk waves propagating in volume, which is unsuitable for a surface treated material, possessing a significant variation in material properties with depth. With knowledge of nonlinear elastic parameters – third-order elastic constants (TOEC) close to the surface of the sample, the acoustoelastic effect might be used with surface acoustic waves. This work is focused on the development of an independent method of TOEC measurement using the effect of nonlinear surface acoustic waves scattering – i.e. the effect of elastic waves interaction in a nonlinear medium.
In this paper, the possible three wave interactions of surface guided waves and bulk waves are described and formulae for the efficiency of harmonic generation and mode mixing are derived. A comparison of the efficiency of surface waves scattering in an isotropic medium for different interaction types is carried out with the help of nonlinear perturbation theory. First results for surface and bulk wave mixing with known second- and third-order elastic constants are shown.
Surface treatment intensity monitoring is still an open and challenging nondestructive testing problem. For the estimation of residual stress with ultrasonic measurements, local linear and nonlinear elastic constants are needed as input. In this paper, nonlinear elastic-wave interactions (also called wave mixing or scattering) — namely, the generation of secondary ultrasonic waves in a nonlinear medium — are considered as a prospective means for near-surface nonlinear elastic parameter evaluation. The allowed interactions between bulk and surface waves, as well as the dependence of the scattering efficiency on the frequency and angle between source waves, were investigated through an analytical model, then compared with FEM simulations and experimental results. Finally, possible future steps for the development of the applied methods for the determination of near-surface higher-order elastic constants are discussed. In addition, several problem-relevant data processing procedures are presented.
The characteristic features and applications of linear and nonlinear guided elastic waves propagating along surfaces (2D) and wedges (1D) are discussed. Laser-based excitation, detection, or contact-free analysis of these guided waves with pump–probe methods are reviewed. Determination of material parameters by broadband surface acoustic waves (SAWs) and other applications in nondestructive evaluation (NDE) are considered. The realization of nonlinear SAWs in the form of solitary waves and as shock waves, used for the determination of the fracture strength, is described. The unique properties of dispersion-free wedge waves (WWs) propagating along homogeneous wedges and of dispersive wedge waves observed in the presence of wedge modifications such as tip truncation or coatings are outlined. Theoretical and experimental results on nonlinear wedge waves in isotropic and anisotropic solids are presented.