Refine
Year of publication
Document Type
- Conference Proceeding (260)
- Article (reviewed) (215)
- Article (unreviewed) (96)
- Part of a Book (76)
- Report (38)
- Patent (37)
- Book (34)
- Contribution to a Periodical (21)
- Doctoral Thesis (5)
- Other (1)
- Periodical Part (1)
- Study Thesis (1)
- Working Paper (1)
Conference Type
- Konferenzartikel (180)
- Konferenz-Abstract (47)
- Konferenz-Poster (15)
- Sonstiges (13)
- Konferenzband (7)
Language
- English (445)
- German (340)
- Other language (1)
Has Fulltext
- no (786) (remove)
Keywords
- Dünnschichtchromatographie (26)
- Energieversorgung (13)
- Adsorption (11)
- Finite-Elemente-Methode (11)
- Plastizität (11)
- TRIZ (11)
- injury (10)
- Ermüdung (9)
- Geothermie (9)
- Materialermüdung (9)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (786) (remove)
Open Access
- Closed Access (268)
- Open Access (244)
- Closed (136)
- Bronze (72)
- Diamond (13)
- Gold (6)
- Hybrid (3)
In den letzten Jahren sind verstärkt große Batteriespeichersysteme in der Mittel- und Hochspannungsebene in Deutschland installiert worden. Neben dem Einsatz für lokale Anwendungszwecke wie Eigenverbrauchsmaximierung oder Lastspitzenkappung sind seit 2016 etwa 250 MW aus Batteriespeichern für die Teilnahme am Markt für Primärregelleistung (PRL) präqualifiziert worden. Damit können bereits 40 % des aktuellen Bedarfs der deutschen Übertragungsnetzbetreiber (ÜNB) gedeckt werden. Für einen zuverlässigen Betrieb von Batteriespeichern sind intelligente Betriebsstrategien erforderlich, die im Rahmen dieser Analyse vorgestellt werden.
In this paper, the effect of the polycrystalline microstructure on crack-tip opening displacement and crack closure is investigated for microstructural short plane strain fatigue cracks using the finite-element method. To this end, cracks are introduced in synthetically generated microstructures and the grain properties are described using a single crystal plasticity model with kinematic hardening. Additionally, finite-element calculations without resolved microstructure and von Mises plasticity with kinematic hardening are performed. Fully-reversed strain-controlled cyclic loadings are considered under large-scale yielding conditions as typical for low-cycle fatigue problems. The crack opening stress and the cyclic crack-tip opening displacement are significantly influenced by the local grain structure. While the stabilized crack opening stresses obtained with the microstructure-based finite-element model are in good accordance with the von Mises plasticity results, the differences in the cyclic crack opening displacement are addressed to the asymmetric plastic strain fields in the plastic wake behind the crack-tip of the microstructure-based model. The asymmetric plastic strain fields result in discontinuous and premature contact of the crack flanks.
Heat pumps play a central role in decarbonizing the heat supply of buildings. However, in this article, implementing heat pumps in existing buildings, a significant challenge is still presented due to high temperature requirements. In this article, a systematic analysis of the effects of heat source temperatures, maximum heat pump condenser temperatures, and system temperatures on the seasonal performance of heat pump (HP) systems is presented. The quantitative performance analysis encompasses over 50 heat pumps installed in residential buildings, revealing correlations between the building characteristics, observed temperatures, and heat pump type. The performance of an HP system retrofitted to a 30-dwelling multifamily building is presented in more detail. The bivalent HP system combines air and ground as heat sources and achieves a seasonal performance factor of 3.25 with a share of the gas boiler of 27% in its first year of operation. In these findings, the technical feasibility of retrofitting heat pumps is demonstrated in existing buildings and insights are provided into overcoming the challenges associated with high temperature requirements.
Uptakes of 9.2 mmol g−1 (40.5 wt %) for CO2 at 273 K/0.1 MPa and 15.23 mmol g−1 (3.07 wt %) for H2 at 77 K/0.1 MPa are among the highest reported for metal–organic frameworks (MOFs) and are found for a novel, highly microporous copper‐based MOF (see picture; Cu turquoise, O red, N blue). Thermal analyses show a stability of the flexible framework up to 250 °C.
Metal–organic frameworks (MOFs) as highly porous materials have gained increasing interest because of their distinct adsorption properties.1–3 They exhibit a high potential for applications in gas separation and storage,4 as sensors5 as well as in heterogeneous catalysis.6 In the last few years, the H2 storage capacity of MOFs has been considerably increased. Mesoporous MOFs show high adsorption capacities for CH4, CO2, and H2 at high pressures.2, 3, 7–10 To increase the uptake of H2 and CO2 by physisorption at ambient pressure, adsorbents with small micropores as well as high specific surface areas and micropore volumes are required.11, 12 Such microporous materials seem to be more appropriate for gas‐mixture separation by physisorption than mesoporous materials. For gas separation in MOFs the interactions between the fluid adsorptive and “open metal sites” (coordinatively unsaturated binding sites) or the ligands are regarded as important.13 Industrial processes, such as natural‐gas purification or biogas upgrading, can be improved with those materials during a vapor‐pressure swing adsorption cycle (VPSA cycle) or a temperature swing adsorption cycle (TSA cycle).14 The microporous MOF series CPO‐27‐M (M=Mg, Co, Ni, Zn), for example, shows very high CO2 uptakes at low pressures (<0.1 MPa).15, 16 Concerning H2 adsorption, the microporous MOF PCN‐12 offers with 3.05 wt % the highest uptake at ambient pressure and 77 K reported to date.17
Herein, we present a novel microporous copper‐based MOF equation image[Cu(Me‐4py‐trz‐ia)] (1; Me‐4py‐trz‐ia2−=5‐(3‐methyl‐5‐(pyridin‐4‐yl)‐4H‐1,2,4‐triazol‐4‐yl)isophthalate) with extraordinarily high CO2 and H2 uptakes at ambient pressure, the H2 uptake being similar to that in PCN‐12. The ligand Me‐4py‐trz‐ia2−, which can be obtained from cheap starting materials by a three‐step synthesis in good yield, combines carboxylate, triazole, and pyridine functions and is adopted from a recently presented series of linkers,18 for which up to now only a few coordination polymers are known.