Refine
Year of publication
Document Type
- Conference Proceeding (35) (remove)
Conference Type
- Konferenzartikel (35)
Is part of the Bibliography
- yes (35)
Keywords
- Eingebettetes System (3)
- Kommunikation (2)
- Car-2-Car communication (1)
- Car-2-X communication (1)
- Design (1)
- Drahtloses lokales Netz (1)
- Energieverbrauch (1)
- Fahrzeug (1)
- Funktechnik (1)
- Gebäudeleittechnik (1)
Institute
Open Access
- Closed Access (19)
- Open Access (9)
- Closed (4)
- Bronze (3)
IPv6 over resource-constrained devices (6Lo) emerged as a de-facto standard for the Internet of Things (IoT) applications especially in home and building automation systems. We provide results of an investigation of the applicability of 6LoWPAN with RPL mesh networks for home and building automation use cases. The proper selection of Trickle parameters and neighbor reachable time-outs is important in the RPL protocol suite to respond efficiently to any path failure. These parameters were analyzed in the context of energy consumption w.r.t the number of control packets. The measurements were performed in an Automated Physical Testbeds (APTB). The results match the recommendation by RFC 7733 for selecting various parameters of RPL protocol suite. This paper shows the relationship between various RPL parameters and control traffic overhead during network rebuild. Comparative measurement results with Bluetooth Low Energy (BLE) in this work showed that 6Lo with RPL outperformed BLE in this use case with less control traffic overheads.
The monitoring of industrial environments ensures that highly automated processes run without interruption. However, even if the industrial machines themselves are monitored, the communication lines are currently not continuously monitored in todays installations. They are checked usually only during maintenance intervals or in case of error. In addition, the cables or connected machines usually have to be removed from the system for the duration of the test. To overcome these drawbacks, we have developed and implemented a cost-efficient and continuous signal monitoring of Ethernet-based industrial bus systems. Several methods have been developed to assess the quality of the cable. These methods can be classified to either passive or active. Active methods are not suitable if interruption of the communication is undesired. Passive methods, on the other hand, require oversampling, which calls for expensive hardware. In this paper, a novel passive method combined with undersampling targeting cost-efficient hardware is proposed.
6LoWPAN (IPv6 over Low Power Wireless Personal Area Networks) is gaining more and more attraction for the seamless connectivity of embedded devices for the Internet of Things. It can be observed that most of the available solutions are following an open source approach, which significantly leads to a fast development of technologies and of markets. Although the currently available implementations are in a pretty good shape, all of them come with some significant drawbacks. It was therefore decided to start the development of an own implementation, which takes the advantages from the existing solutions, but tries to avoid the drawbacks. This paper discussed the reasoning behind this decision, describes the implementation and its characteristics, as well as the testing results. The given implementation is available as open-source project under [15].
A highly scalable IEEE802.11p communication and localization subsystem for autonomous urban driving
(2013)
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed for the support of highly autonomous driving. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. Thus it is mainly targeted for the support of traffic safety applications in intra-urban scenarios. This contribution describes the Ko-TAG part of the overall initiative, which develops a subsystem to improve the real-time characteristics of IEEE802.11p needed for precise time of flight real-time localization. In doing this, it still fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. Test results are shown in the last part of the paper.
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed and its benefit for traffic safety applications is evaluated. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. The Ko-TAG proposal enriches the current IEEE802.11p real-time characteristics needed for precise time-of-flight real-time localization. This contribution describes the development of a subsystem, which extends the functionality of IEEE802.11p and fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. The next step will be field measurements to verify the simulation results.
A novel approach of a testbed for embedded networking nodes has been conceptualized and implemented. It is based on the use of virtual nodes in a PC environment, where each node executes the original embedded code. Different nodes are running in parallel and are connected via so-called virtual interfaces. The presented approach is very efficient and allows a simple description of test cases without the need of a network simulator. Furthermore, it speeds up the process of developing new features.
The Metering Bus, also known as M-Bus, is a European standard EN13757-3 for reading out metering devices, like electricity, water, gas, or heat meters. Although real-life M-Bus networks can reach a significant size and complexity, only very simple protocol analyzers are available to observe and maintain such networks. In order to provide developers and installers with the ability to analyze the real bus signals easily, a web-based monitoring tool for the M-Bus has been designed and implemented. Combined with a physical bus interface it allows for measuring and recording the bus signals. For this at first a circuit has been developed, which transforms the voltage and current-modulated M-Bus signals to a voltage signal that can be read by a standard ADC and processed by an MCU. The bus signals and packets are displayed using a web server, which analyzes and classifies the frame fragments. As an additional feature an oscilloscope functionality is included in order to visualize the physical signal on the bus. This paper describes the development of the read-out circuit for the Wired M-Bus and the data recovery.
Wireless communication networks are crucial for enabling megatrends like the Internet of Things (IoT) and Industry 4.0. However, testing these networks can be challenging due to the complex network topology and RF characteristics, requiring a multitude of scenarios to be tested. To address this challenge, the authors developed and extended an automated testbed called Automated Physical TestBed (APTB). This testbed provides the means to conduct controlled tests, analyze coexistence, emulate multiple propagation paths, and model dependable channel conditions. Additionally, the platform supports test automation to facilitate efficient and systematic experimentation. This paper describes the extended architecture, implementation, and performance evaluation of the APTB testbed. The APTB testbed provides a reliable and efficient solution for testing wireless communication networks under various scenarios. The implementation and performance verification of the testbed demonstrate its effectiveness and usefulness for researchers and industry practitioners.
Institute of Reliable Embedded Systems and Communication Electronics, Offenburg University of Applied Sciences, Germany has developed an automated testing environment, Automated Physical TestBeds (APTB), for analyzing the performance of wireless systems and its supporting protocols. Wireless physical networking nodes can connect to this APTB and the antenna output of this attaches with the RF waveguides. To model the RF environment this RF waveguides then establish wired connection among RF elements like splitters, attenuators and switches. In such kind of set up it’s well possible to vary the path characteristics by altering the attenuators and switches. The major advantage of using APTB is the possibility of isolated, well controlled, repeatable test environment in various conditions to run statistical analysis and even to execute regression tests. This paper provides an overview of the design and implementation of APTB, demonstrates its ability to automate test cases, and its efficiency.
Automated RF Emulator for a Highly Scalable IEEE802.11p Communication and Localization Subsystem
(2014)
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed for the support of highly autonomous driving. The Ko-TAG subsystem improves the real-time characteristics of IEEE802.11p needed for precise time of flight real-time localization while still fitting into the regulatory schemes. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. The Ko-TAG subsystem mainly concentrates on the support of traffic safety applications in intra-urban scenarios. This paper details on the development of a fully automated RF emulator used to test the Ko-TAG subsystem.
The RF emulator includes the physical networking nodes, but models the RF environment using RF-waveguides. The RF emulator allows the controlling of path loss and connectivity between any of the nodes with the help of RF attenuators and programmable RF switches, while it is shielded against its surrounding RF environment in the lab. Therefore it is an inexpensive alternative to an RF absorber chamber, which often is not available or exceeds the project’s budget.
Details about the system definition can be found in earlier papers. Test results are shown in the last part of the paper.