Refine
Year of publication
Document Type
- Article (reviewed) (10)
- Conference Proceeding (4)
- Contribution to a Periodical (2)
- Article (unreviewed) (2)
- Report (1)
Conference Type
- Konferenzartikel (4)
Is part of the Bibliography
- yes (19)
Keywords
- Energieversorgung (4)
- Digitaler Zwilling (2)
- Lichtbogenofen (2)
- Maschinenbaustudium (2)
- Virtuelles Laboratorium (2)
- Wärmeübertragung (2)
- digital twin (2)
- virtual lab (2)
- Abwärmenutzung (1)
- Boiler (1)
Institute
Open Access
- Open Access (11)
- Closed Access (6)
- Diamond (2)
Im Fahrzeug stehen große Wärmeströme zur Verfügung, die nicht genutzt werden. Die Energie des Abgases weist gegenüber der des Motor/Kühlsystems eine wesentlich höhere Arbeitsfähigkeit auf. Untersuchungen zielen dahin, diese thermische Energie zum Beispiel mithilfe eines thermoelektrischen Generators wieder in das System einzukoppeln und als Energiequelle für Verbraucher zu nutzen.
Zum ersten Mal gibt es mit dem kooperativen Promotionskolleg über „Kleinskalige erneuerbare Energiesysteme – KleE“ für hochqualifizierte Absolventen der Hochschule Offenburg die Möglichkeit zur Promotion innerhalb des engen wissenschaftlichen Austauschs eines Doktorandenkollegs. Betreut werden sie gemeinsam von je einem Universitätsprofessor und einem Hochschulprofessor. In Zusammenarbeit mit der Albert-Ludwigs-Universität Freiburg, dem Zentrum für Erneuerbare Energien (ZEE), und den Fraunhofer-Instituten für Solare Energiesysteme (ISE) sowie für Physikalische Messtechnik (IPM) forschen 15 Doktorandinnen und Doktoranden im Promotionskolleg KleE an interdisziplinären Forschungsthemen.
Innovative combined heat, cold and power (Trigeneration) at Offenburg University of Applied Sciences
(2013)
The aim of the paper was to investigate the energy saved in the shift from separate generation of thermal and electrical energy to trigeneration at the energy facility in Offenburg University of Applied Sciences (HS OG). The energy facility at HS OG used a traditional heating system and electricity from grid until 2007 afterwhich they installed a trigeneration system to meet its continuously changing dynamic thermal and electrical demands. This paper highlights the methodology that had been derived to analyze and study the effect of this shift based on the energy consumption data available from 2004 to 2011, which were scarce due to the limited monitoring. From the energy analysis, we concluded that 8 % primary energy was saved in this shift at the energy facility of HS OG. And from economical perspective 5 % useful thermal energy and 39 % useful electrical energy was saved in this shift at the energy facility of HS OG. Nevertheless, the term energy saving, in general, is very relative and complex to define in such a changeover.
The energy supply of Offenburg University of Applied Sciences (HS OG) was changed from separate generation to trigeneration in 2007/2008. Trigeneration was installed for supplying heat, cooling and electrical power at HS OG. In this paper, trigeneration process and its modes of operation along with the layout of the energy facility at HS OG were described. Special emphasis was given to the operation schemes and control strategies of the operation modes: winter mode, transition mode and summer mode. The components used in the energy facility were also outlined. Monitoring and data analysis of the energy system was carried out after the commissioning of trigeneration in the period from 2008 to 2011. Thus, valuable performance data was obtained.
Packed beds serve as thermal energy storages (TES) and heat exchangers (HEX) in different technological applications. In this paper, a general heterogeneous model of heat transfer in packed beds is developed. It is implemented by lumped element formulation in object-oriented modeling language Modelica and is successful validated with data sets taken from two different experiments reported in literature.
The main advantages of the introduced model are the general, theory-based approach and the lumped element formulation in Modelica. The first point mentioned above should allow to simulate a packed bed TES/HEX without the necessity applying measured data for model calibration or to apply specific heat transfer correlations with restricted application. The second point establishes the possibility to integrate the TES/HEX model within plant models of larger scale without increasing the simulation time drastically.
The aim of this research work was to develop a boiler model with few parameters required for energy planning. The showcase considered for this work was the boiler system of the energy center at Offenburg University of Applied Sciences. A grey box model of the boiler was developed systematically starting from model abstraction, simplification, model break-down and to the use of empirical correlations wherever necessary to describe the intermediate effects along with the use of information from manufacturer’s specification in order to reduce parameters. This strategy had resulted in a boiler model with only 6 parameters, namely, nominal burner capacity, water gallery capacity, air ratio, heat capacity of wall, thermal conductance on flue gas and hot water side. Most of these parameters can be obtained through the information available in the spec sheets and thus an energy planner will be able to parameterize the model with low effort. The model was validated with the monitored data of the showcase. It was tested for the start-up, shut-down behavior and the effect of storage.
Electric arc furnaces (EAF) are complex industrial plants whose actual behavior depends upon numerous factors. Due to its energy intensive operation, the EAF process has always been subject to optimization efforts. For these reasons, several models have been proposed in literature to analyze and predict different modes of operation. Most of these models focused on the processes inside the vessel itself. The present paper introduces a dynamic, physics-based model of a complete EAF plant which consists of the four subsystems vessel, electric system, electrode regulation, and off-gas system. Furthermore the solid phase is not treated to be homogenous but a simple spatial discretization is employed. Hence it is possible to simulate the energy input by electric arcs and fossil fuel burners depending on the state of the melting progress. The model is implemented in object-oriented, equation-based language Modelica. The simulation results are compared to literature data.
Physics-based Modeling of the Electric Arc furnace Process using Object-Oriented Language Modelica
(2016)
Electric arc furnaces (EAF) are complex industrial plants whose actual behavior depends upon numerous factors. Due to its energy intensive operation, the EAF process has always been subject to optimization efforts. For these reasons, several models have been proposed in literature to analyze and predict different modes of operation. Most of these models focused on the processes inside the vessel itself. The present paper introduces a dynamic, physics-based model of a complete EAF plant which consists of the four subsystems vessel, electric system, electrode regulation, and off-gas system. Furthermore the solid phase is not treated to be homogenous but a simple spatial discretization is employed. Hence it is possible to simulate the energy input by electric arcs and fossil fuel burners depending on the state of the melting progress. The model is implemented in object-oriented, equation-based language Modelica. The simulation results are compared to literature data.