Refine
Document Type
Conference Type
- Konferenzartikel (1)
Language
- English (4)
Has Fulltext
- no (4)
Is part of the Bibliography
- yes (4) (remove)
Open Access
- Closed Access (2)
- Closed (1)
- Open Access (1)
Many different methods, such as screen printing, gravure, flexography, inkjet etc., have been employed to print electronic devices. Depending on the type and performance of the devices, processing is done at low or high temperature using precursor- or particle-based inks. As a result of the processing details, devices can be fabricated on flexible or non-flexible substrates, depending on their temperature stability. Furthermore, in order to reduce the operating voltage, printed devices rely on high-capacitance electrolytes rather than on dielectrics. The printing resolution and speed are two of the major challenging parameters for printed electronics. High-resolution printing produces small-size printed devices and high-integration densities with minimum materials consumption. However, most printing methods have resolutions between 20 and 50 μm. Printing resolutions close to 1 μm have also been achieved with optimized process conditions and better printing technology.
The final physical dimensions of the devices pose severe limitations on their performance. For example, the channel lengths being of this dimension affect the operating frequency of the thin-film transistors (TFTs), which is inversely proportional to the square of channel length. Consequently, short channels are favorable not only for high-frequency applications but also for high-density integration. The need to reduce this dimension to substantially smaller sizes than those possible with today’s printers can be fulfilled either by developing alternative printing or stamping techniques, or alternative transistor geometries. The development of a polymer pen lithography technique allows scaling up parallel printing of a large number of devices in one step, including the successive printing of different materials. The introduction of an alternative transistor geometry, namely the vertical Field Effect Transistor (vFET), is based on the idea to use the film thickness as the channel length, instead of the lateral dimensions of the printed structure, thus reducing the channel length by orders of magnitude. The improvements in printing technologies and the possibilities offered by nanotechnological approaches can result in unprecedented opportunities for the Internet of Things (IoT) and many other applications. The vision of printing functional materials, and not only colors as in conventional paper printing, is attractive to many researchers and industries because of the added opportunities when using flexible substrates such as polymers and textiles. Additionally, the reduction of costs opens new markets. The range of processing techniques covers laterally-structured and large-area printing technologies, thermal, laser and UV-annealing, as well as bonding techniques, etc. Materials, such as conducting, semiconducting, dielectric and sensing materials, rigid and flexible substrates, protective coating, organic, inorganic and polymeric substances, energy conversion and energy storage materials constitute an enormous challenge in their integration into complex devices.
Fully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates
(2020)
Printed and flexible metal‐oxide transistor technology has recently demonstrated great promise due to its high performance and robust mechanical stability. Herein, fully printed inverter structures using electrolyte‐gated oxide transistors on a flexible polyimide (PI) substrate are discussed in detail. Conductive graphene ink is printed as the passive structures and interconnects. The additive printed transistors on PI substrates show an on/off ratio of 106 and show mobilities similar to the state‐of‐the‐art printed transistors on rigid substrates. Printed meander structures of graphene are used as pull‐up resistances in a transistor–resistor logic to create fully printed inverters. The printed and flexible inverters show a signal gain of 3.5 and a propagation delay of 30 ms. These printed inverters are able to withstand a tensile strain of 1.5% following more than 200 cycles of mechanical bending. The stability of the electrical direct current (DC) properties has been observed over a period of 5 weeks. These oxide transistor‐based fully printed inverters are relevant for digital printing methods which could be implemented into roll‐to‐roll processes.
In this report, we have studied field-effect transistors (FETs) using low-density alumina for electrolytic gating. Device layers have been prepared starting from the structured ITO glasses by printing the In 2 O 3 channels, low-temperature atomic layer deposition (ALD) of alumina (Al 2 O 3 ), and printing graphene top gates. The transistor performance could be deliberately changed by alternating the ambient humidity; furthermore, ID,ON/ID,OFF-ratios of up to seven orders of magnitude and threshold voltages between 0.66 and 0.43 V, decreasing with an increasing relative humidity between 40% and 90%, could be achieved. In contrast to the common usage of Al 2 O 3 as the dielectric in the FETs, our devices show electrolyte-typegating behavior. This is a result from the formation of protons on the Al 2 O 3 surfaces at higher humidities. Due to the very high local capacitances of the Helmholtz double layers at the channel surfaces, the operation voltage can be as low as 1 V. At low humidities (≤30%), the solid electrolyte dries out and the performance breaks down; however, it can fully reversibly be regained upon a humidity increase. Using ALD-derived alumina as solid electrolyte gating material, thus, allows low-voltage operation and provides a chemically stable gating material while maintaining low process temperatures. However, it has proven to be highly humidity-dependent in its performance.
Development of Fully Printed Oxide Field-Effect Transistors using Graphene Passive Structures
(2019)
During the past decade to the present time, the topic of printed electronics has gained a lot of attention for their potential use in a number of practical applications, including biosensors, photovoltaic devices, RFIDs, flexible displays, large-area circuits, and so on. To fully realize printed electronic components and devices, effective techniques for the printing of passive structures and electrically and chemically compatible materials in the printed devices need to be developed first. The opportunity of using electrically conducting graphene inks will enable the integration of passive structures into active devices, as for example, printed electrolyte-gated transistors (EGTs). Accordingly, in this study, we present the parametric results obtained on fully printed electrolyte-gated transistors having graphene as the passive electrodes, an inorganic oxide semiconductor as the active channel, and a composite solid polymer electrolyte (CSPE) as the gate insulating material. This configuration offers high chemical and electrical stability while at the same time allowing EGT operation at low potentials, implying the distinct advantage of operation at low input voltages. The printed in-plane EGTs we developed exhibit excellent performance with device mobility up to 16 cm2 V–1 s–1, an ION/IOFF ratio of 105, and a subthreshold slope of 120 mV dec–1.