Refine
Document Type
- Article (reviewed) (74) (remove)
Has Fulltext
- no (74) (remove)
Is part of the Bibliography
- yes (74)
Keywords
- Johann Sebastian Bach (3)
- Regelungstechnik (3)
- 3D-CAD (2)
- Biomechanik (2)
- Handprothese (2)
- Predictive maintenance (2)
- esophageal catheter (2)
- 3D CAD (1)
- 3D Strukturlichtscanner (1)
- 3D-Visualisierung (1)
Institute
- Fakultät Elektrotechnik, Medizintechnik und Informatik (EMI) (ab 04/2019) (74) (remove)
Open Access
- Closed Access (36)
- Open Access (21)
- Closed (14)
- Bronze (1)
- Diamond (1)
- Gold (1)
- Hybrid (1)
Analysing and predicting the advance rate of a tunnel boring machine (TBM) in hard rock is integral to tunnelling project planning and execution. It has been applied in the industry for several decades with varying success. Most prediction models are based on or designed for large-diameter TBMs, and much research has been conducted on related tunnelling projects. However, only a few models incorporate information from projects with an outer diameter smaller than 5 m and no penetration prediction model for pipe jacking machines exists to date. In contrast to large TBMs, small-diameter TBMs and their projects have been considered little in research. In general, they are characterised by distinctive features, including insufficient geotechnical information, sometimes rather short drive lengths, special machine designs and partially concurring lining methods like pipe jacking and segment lining. A database which covers most of the parameters mentioned above has been compiled to investigate the performance of small-diameter TBMs in hard rock. In order to provide sufficient geological and technical variance, this database contains 37 projects with 70 geotechnically homogeneous areas. Besides the technical parameters, important geotechnical data like lithological information, unconfined compressive strength, tensile strength and point load index is included and evaluated. The analysis shows that segment lining TBMs have considerably higher penetration rates in similar geological and technical settings mostly due to their design parameters. Different methodologies for predicting TBM penetration, including state-of-the-art models from the literature as well as newly derived regression and machine learning models, are discussed and deployed for backward modelling of the projects contained in the database. New ranges of application for small-diameter tunnelling in several industry-standard penetration models are presented, and new approaches for the penetration prediction of pipe jacking machines in hard rock are proposed.
Precisely synchronized communication is a major precondition for many industrial applications. At the same time, hardware cost and power consumption need to be kept as low as possible in the Internet of Things (IoT) paradigm. While many wired solutions on the market achieve these requirements, wireless alternatives are an interesting field for research and development. This article presents a novel IEEE802.11n/ac wireless solution, exhibiting several advantages over state-of-the-art competitors. It is based on a market-available wireless System on a Chip with modified low-level communication firmware combined with a low-cost field-programmable gate array. By achieving submicrosecond synchronization accuracy, our solution outperforms the precision of low-cost products by almost four orders of magnitude. Based on inexpensive hardware, the presented wireless module is up to 20 times cheaper than software-defined-radio solutions with comparable timing accuracy. Moreover, it consumes three to five times less power. To back up our claims, we report data that we collected with a high sampling rate (2000 samples per second) during an extended measurement campaign of more than 120 h, which makes our experimental results far more representative than others reported in the literature. Additional support is provided by the size of the testbed we used during the experiments, composed of a hybrid network with nine nodes divided into two independent wireless segments connected by a wired backbone. In conclusion, we believe that our novel Industrial IoT module architecture will have a significant impact on the future technological development of high-precision time-synchronized communication for the cost-sensitive industrial IoT market.
Am 1. Juli 2022 trafen sich im Rahmen des Abschlusskolloquiums des Projekts ACA-Modes rund 60 Teilnehmende aus Forschung, Lehre und Industrie zu einer internationalen Konferenz an der Hochschule Offenburg. Hier wurden die Projektergebnisse rund um die erfolgreiche Implementierung modellprädiktiver Regelstrategien vorgestellt, aktuelle Fragestellungen diskutiert und Entwicklungspfade hin zu einem netzdienlichen Betrieb von Energieverbundsystemen skizziert.
Physical unclonable functions (PUFs) are increasingly generating attention in the field of hardware-based security for the Internet of Things (IoT). A PUF, as its name implies, is a physical element with a special and unique inherent characteristic and can act as the security anchor for authentication and cryptographic applications. Keeping in mind that the PUF outputs are prone to change in the presence of noise and environmental variations, it is critical to derive reliable keys from the PUF and to use the maximum entropy at the same time. In this work, the PUF output positioning (POP) method is proposed, which is a novel method for grouping the PUF outputs in order to maximize the extracted entropy. To achieve this, an offset data is introduced as helper data, which is used to relax the constraints considered for the grouping of PUF outputs, and deriving more entropy, while reducing the secret key error bits. To implement the method, the key enrollment and key generation algorithms are presented. Based on a theoretical analysis of the achieved entropy, it is proven that POP can maximize the achieved entropy, while respecting the constraints induced to guarantee the reliability of the secret key. Moreover, a detailed security analysis is presented, which shows the resilience of the method against cyber-security attacks. The findings of this work are evaluated by applying the method on a hybrid printed PUF, where it can be practically shown that the proposed method outperforms other existing group-based PUF key generation methods.
Neural networks tend to overfit the training distribution and perform poorly on out-ofdistribution data. A conceptually simple solution lies in adversarial training, which introduces worst-case perturbations into the training data and thus improves model generalization to some extent. However, it is only one ingredient towards generally more robust models and requires knowledge about the potential attacks or inference time data corruptions during model training. This paper focuses on the native robustness of models that can learn robust behavior directly from conventional training data without out-of-distribution examples. To this end, we study the frequencies in learned convolution filters. Clean-trained models often prioritize high-frequency information, whereas adversarial training enforces models to shift the focus to low-frequency details during training. By mimicking this behavior through frequency regularization in learned convolution weights, we achieve improved native robustness to adversarial attacks, common corruptions, and other out-of-distribution tests. Additionally, this method leads to more favorable shifts in decision-making towards low-frequency information, such as shapes, which inherently aligns more closely with human vision.
Unterschiedliche Stimulationszeitpunkte bei bimodaler Versorgung mit Hörgerät und Cochleaimplantat
(2023)
Die bimodale Versorgung von Patienten mit Hörgerät (HG) ipsilateral und Cochleaimplantat (CI) kontralateral bei asymmetrischem Hörverlust ist aufgrund vieler inhärenter Variablen die komplizierteste Versorgungsart im Kontext der Versorgung mit CI. Im vorliegenden Übersichtsartikel werden alle systematischen interauralen Unterschiede zwischen elektrischer und akustischer Stimulation dargestellt, die bei dieser Versorgungsart auftreten können. Darüber hinaus werden Methoden zur Quantifizierung des interauralen Latenzoffsets, also des Zeitunterschieds zwischen der akustischen und elektrischen Stimulation des Hörnervs, mittels Registrierung auditorisch evozierter Potenziale – erzeugt durch akustische bzw. elektrische Stimulation – und Messungen an den Sprachprozessoren und Hörgeräten vorgestellt. Die technische Kompensation des interauralen Latenzoffsets und ihre positive Auswirkung auf die Schalllokalisationsfähigkeit bimodal mit CI und HG versorgter Patienten wird ebenfalls beschrieben. Zuletzt werden neueste Erkenntnisse diskutiert, die Gründe dafür aufzeigen, warum die Kompensation des interauralen Latenzoffsets das Sprachverstehen im Störgeräusch bei bimodal versorgten CI-/HG-Trägern nicht verbessert.
Die Optimierung der Auftragsterminierung und Einsteuerungsreihenfolge hat großen Einfluss auf die Produktivität von Fertigungssystemen. Genetische Algorithmen und Simulation sind verbreitete Werkzeuge zur Optimierung. Dieser Beitrag beschreibt einen neuen Ansatz zur Optimierung durch einen genetischen Algorithmus und der Simulation in dynamischen Modellen. Eine illustrative Fallstudie validiert den Ansatz und zeigt das Potenzial zur ganzheitlichen Verbesserung von Fertigungssystemen auf.
Inadequate mechanical compliance of orthopedic implants can result in excessive strain of the bone interface, and ultimately, aseptic loosening. It is hypothesized that a fiber-based biometal with adjustable anisotropic mechanical properties can reduce interface strain, facilitate continuous remodeling, and improve implant survival under complex loads. The biometal is based on strategically layered sintered titanium fibers. Six different topologies are manufactured. Specimens are tested under compression in three orthogonal axes under 3-point bending and torsion until failure. Biocompatibility testing involves murine osteoblasts. Osseointegration is investigated by micro-computed tomography and histomorphometry after implantation in a metaphyseal trepanation model in sheep. The material demonstrates compressive yield strengths of up to 50 MPa and anisotropy correlating closely with fiber layout. Samples with 75% porosity are both stronger and stiffer than those with 85% porosity. The highest bending modulus is found in samples with parallel fiber orientation, while the highest shear modulus is found in cross-ply layouts. Cell metabolism and morphology indicate uncompromised biocompatibility. Implants demonstrate robust circumferential osseointegration in vivo after 8 weeks. The biometal introduced in this study demonstrates anisotropic mechanical properties similar to bone, and excellent osteoconductivity and feasibility as an orthopedic implant material.
Aerosol particles play an important role in the climate system by absorbing and scattering radiation and influencing cloud properties. They are also one of the biggest sources of uncertainty for climate modeling. Many climate models do not include aerosols in sufficient detail due to computational constraints. To represent key processes, aerosol microphysical properties and processes have to be accounted for. This is done in the ECHAM-HAM (European Center for Medium-Range Weather Forecast-Hamburg-Hamburg) global climate aerosol model using the M7 microphysics, but high computational costs make it very expensive to run with finer resolution or for a longer time. We aim to use machine learning to emulate the microphysics model at sufficient accuracy and reduce the computational cost by being fast at inference time. The original M7 model is used to generate data of input–output pairs to train a neural network (NN) on it. We are able to learn the variables’ tendencies achieving an average R² score of 77.1%. We further explore methods to inform and constrain the NN with physical knowledge to reduce mass violation and enforce mass positivity. On a Graphics processing unit (GPU), we achieve a speed-up of up to over 64 times faster when compared to the original model.
Many commonly well-performing convolutional neural network models have shown to be susceptible to input data perturbations, indicating a low model robustness. To reveal model weaknesses, adversarial attacks are specifically optimized to generate small, barely perceivable image perturbations that flip the model prediction. Robustness against attacks can be gained by using adversarial examples during training, which in most cases reduces the measurable model attackability. Unfortunately, this technique can lead to robust overfitting, which results in non-robust models. In this paper, we analyze adversarially trained, robust models in the context of a specific network operation, the downsampling layer, and provide evidence that robust models have learned to downsample more accurately and suffer significantly less from downsampling artifacts, aka. aliasing, than baseline models. In the case of robust overfitting, we observe a strong increase in aliasing and propose a novel early stopping approach based on the measurement of aliasing.
Im Beitrag wird ein zweistufiges Verfahren für den Entwurf eines Störgrößenbeobachters für lineare, zeitinvariante Systeme vorgestellt. Hierbei wird davon ausgegangen, dass die Beobachterrückführung für den Beobachter ohne Störmodell bereits vorliegt. Es wird dargestellt, wie darauf basierend mit einfachen formelmäßigen Zusammenhängen die Rückführkoeffizienten für den Störgrößenbeobachter ermittelt werden können. Die beschriebene Methode erhöht die Übersichtlichkeit hinsichtlich des Einflusses des Störmodells auf die Beobachterrückführkoeffizienten und ist außerdem für Modelle mit geringer Systemordnung rechenzeitsparender.
Bach, Gas, Strom und Wasser
(2022)
Die Corona-Semester erforderten die Übertragung der Brückenkurse Mathematik in ein digitales Lehr-format. Gerade beim Studieneinstieg spielen persönliche Unterstützung und soziale Eingebundenheit für Studierende eine besonders wichtige Rolle. Deshalb lag die besondere Herausforderung bei der Übertragung in ein digitales Format darin, die wegfallenden üblichen Kennenlern- und Kommunika-tionsmöglichkeiten, die sich in Präsenzformaten beispielsweise in den Pausen oder im Gespräch mit den Sitznachbarn ergeben, zu kompensieren. Vorliegender Beitrag stellt vor, inwieweit der Transfer in ein digitales Format gelungen ist. Das digitale Brückenkurskonzept wurde in ein didaktisches Entwurfsmuster übertragen, um durch die strukturierte und nachvollziehbare Darstellung den Transfer und die Vergleichbarkeit der Ergebnisse zu erleichtern.
Memento mori!
(2022)
Das plötzliche Ende des romantischen Komponisten Felix Mendelssohn Bartholdy (1809–1847) gibt uns auch heute noch Rätsel auf. Einiges deutet auf ein rupturiertes zerebrales Aneurysma mit konsekutiver Subarachnoidalblutung hin. Das Quellenmaterial zu den Symptomen seiner Todeskrankheit wird in dieser Arbeit ausführlich vorgestellt und diskutiert. Eine mögliche familiäre Disposition im Sinne eines Ehlers-Danlos-Syndroms Typ IV wird erörtert.
Significant progress in the development and commercialization of electrically conductive adhesives has been made. This makes shingling a very attractive approach for solar cell interconnection. In this study, we investigate the shading tolerance of two types of solar modules based on shingle interconnection: first, the already commercialized string approach, and second, the matrix technology where solar cells are intrinsically interconnected in parallel and in series. An experimentally validated LTspice model predicts major advantages for the power output of the matrix layout under partial shading. Diagonal as well as random shading of a 1.6-m2 solar module is examined. Power gains of up to 73.8 % for diagonal shading and up to 96.5 % for random shading are found for the matrix technology compared to the standard string approach. The key factor is an increased current extraction due to lateral current flows. Especially under minor shading, the matrix technology benefits from an increased fill factor as well. Under diagonal shading, we find the probability of parts of the matrix module being bypassed to be reduced by 40 % in comparison to the string module. In consequence, the overall risk of hotspot occurrence in matrix modules is decreased significantly.
A versatile liquid metal (LM) printing process enabling the fabrication of various fully printed devices such as intra- and interconnect wires, resistors, diodes, transistors, and basic circuit elements such as inverters which are process compatible with other digital printing and thin film structuring methods for integration is presented. For this, a glass capillary-based direct-write method for printing LMs such as eutectic gallium alloys, exploring the potential for fully printed LM-enabled devices is demonstrated. Examples for successful device fabrication include resistors, p–n diodes, and field effect transistors. The device functionality and easiness of one integrated fabrication flow shows that the potential of LM printing is far exceeding the use of interconnecting conventional electronic devices in printed electronics.
Objective: To quantify the effect of inhaled 5% carbon-dioxide/95% oxygen on EEG recordings from patients in non-convulsive status epilepticus (NCSE).
Methods: Five children of mixed aetiology in NCSE were given high flow of inhaled carbogen (5% carbon dioxide/95% oxygen) using a face mask for maximum 120s. EEG was recorded concurrently in all patients. The effects of inhaled carbogen on patient EEG recordings were investigated using band-power, functional connectivity and graph theory measures. Carbogen effect was quantified by measuring effect size (Cohen's d) between "before", "during" and "after" carbogen delivery states.
Results: Carbogen's apparent effect on EEG band-power and network metrics across all patients for "before-during" and "before-after" inhalation comparisons was inconsistent across the five patients.
Conclusion: The changes in different measures suggest a potentially non-homogeneous effect of carbogen on the patients' EEG. Different aetiology and duration of the inhalation may underlie these non-homogeneous effects. Tuning the carbogen parameters (such as ratio between CO2 and O2, duration of inhalation) on a personalised basis may improve seizure suppression in future.
It is important to minimize the unscheduled downtime of machines caused by outages of machine components in highly automated production lines. Considering machine tools such as, grinding machines, the bearing inside of spindles is one of the most critical components. In the last decade, research has increasingly focused on fault detection of bearings. In addition, the rise of machine learning concepts has also intensified interest in this area. However, up to date, there is no single one-fits-all solution for predictive maintenance of bearings. Most research so far has only looked at individual bearing types at a time.
This paper gives an overview of the most important approaches for bearing-fault analysis in grinding machines. There are two main parts of the analysis presented in this paper. The first part presents the classification of bearing faults, which includes the detection of unhealthy conditions, the position of the error (e.g. at the inner or at the outer ring of the bearing) and the severity, which detects the size of the fault. The second part presents the prediction of remaining useful life, which is important for estimating the productive use of a component before a potential failure, optimizing the replacement costs and minimizing downtime.
In the last decade, deep learning models for condition monitoring of mechanical systems increasingly gained importance. Most of the previous works use data of the same domain (e.g., bearing type) or of a large amount of (labeled) samples. This approach is not valid for many real-world scenarios from industrial use-cases where only a small amount of data, often unlabeled, is available.
In this paper, we propose, evaluate, and compare a novel technique based on an intermediate domain, which creates a new representation of the features in the data and abstracts the defects of rotating elements such as bearings. The results based on an intermediate domain related to characteristic frequencies show an improved accuracy of up to 32 % on small labeled datasets compared to the current state-of-the-art in the time-frequency domain.
Furthermore, a Convolutional Neural Network (CNN) architecture is proposed for transfer learning. We also propose and evaluate a new approach for transfer learning, which we call Layered Maximum Mean Discrepancy (LMMD). This approach is based on the Maximum Mean Discrepancy (MMD) but extends it by considering the special characteristics of the proposed intermediate domain. The presented approach outperforms the traditional combination of Hilbert–Huang Transform (HHT) and S-Transform with MMD on all datasets for unsupervised as well as for semi-supervised learning. In most of our test cases, it also outperforms other state-of-the-art techniques.
This approach is capable of using different types of bearings in the source and target domain under a wide variation of the rotation speed.
Interpreting seismic data requires the characterization of a number of key elements such as the position of faults and main reflections, presence of structural bodies, and clustering of areas exhibiting a similar amplitude versus angle response. Manual interpretation of geophysical data is often a difficult and time-consuming task, complicated by lack of resolution and presence of noise. In recent years, approaches based on convolutional neural networks have shown remarkable results in automating certain interpretative tasks. However, these state-of-the-art systems usually need to be trained in a supervised manner, and they suffer from a generalization problem. Hence, it is highly challenging to train a model that can yield accurate results on new real data obtained with different acquisition, processing, and geology than the data used for training. In this work, we introduce a novel method that combines generative neural networks with a segmentation task in order to decrease the gap between annotated training data and uninterpreted target data. We validate our approach on two applications: the detection of diffraction events and the picking of faults. We show that when transitioning from synthetic training data to real validation data, our workflow yields superior results compared to its counterpart without the generative network.
The increasing use of artificial intelligence (AI) technologies across application domains has prompted our society to pay closer attention to AI’s trustworthiness, fairness, interpretability, and accountability. In order to foster trust in AI, it is important to consider the potential of interactive visualization, and how such visualizations help build trust in AI systems. This manifesto discusses the relevance of interactive visualizations and makes the following four claims: i) trust is not a technical problem, ii) trust is dynamic, iii) visualization cannot address all aspects of trust, and iv) visualization is crucial for human agency in AI.
Die vorliegende Arbeit gibt einen Überblick über das Verhältnis zwischen Nutzen und Einschränkungen eines frühneuzeitlichen Riefelharnisches auf die Biomechanik des Menschen. Zu den zentralen Ergebnissen gehört, dass die Rüstung eine gewisse Einschränkung der Beweglichkeit bringt, jedoch durch verschiedene mechanische Konzepte versucht wurde, diese größtmöglich zu minimieren. Besonders das sogenannte Geschübe stellt hierbei einen Kompromiss zwischen Beweglichkeit und Schutzfunktion dar und findet vor allem im Bereich der Gelenke Anwendung. Steife Strukturen werden an Stellen eingesetzt, die kaum Bewegungsfreiheit fordern. Zu diesen Bereichen gehören beispielsweise der Brustkorb oder obere Teile des Rückens. Der Vorteil der steiferen Teile der Rüstung ist ihre erhöhte Schutzfunktion, die ein geringeres Verletzungsrisiko mit sich bringt.
Fünf Jahre vor seinem Tod, im Jahr 1932, wurde der berühmte französische Komponist Maurice Ravel (1875–1937), der an einer frontotemporalen Demenz (M. Pick) mit primär progressiver Aphasie litt, bei einem Unfall verletzt, als er in einem Pariser Taxi saß. In diesem Fallbericht wird der Unfallmechanismus unter bestimmten Annahmen dargestellt und diskutiert. Ausgehend von diesen Überlegungen ist ein Unfall bei geringer Kollisionsgeschwindigkeit wahrscheinlich. Trotz eines Unfalls mit nur geringer Geschwindigkeit ist nicht von der Hand zu weisen, dass dieser Unfall zumindest zu einer deutlichen Verschlimmerung der Krankheitssymptome geführt haben könnte, da Ravel seit diesem Taxiunfall bis zu seinem Tod keine weiteren Kompositionen mehr vollendet hat.
In dieser Arbeit wird ein historischer Fallbericht des bis heute weit über seine Landesgrenzen bekannten italienischen Kriminalanthropologen Cesare Lombroso (1835–1909) vorgestellt. In diesem Fallbericht wird der berüchtigte und psychisch auffällige Dieb Pietro Bersone mit Hilfe eines sog. Hydrosphygmographen überführt, einem zur damaligen Zeit neuartigen technischen Gerät, das den Puls nicht-invasiv aufzeichnen konnte. Lombroso ist vermutlich einer der ersten, wenn nicht sogar der erste, der durch den Einsatz eines solchen Geräts die Idee zum „Lügendetektor“ vorweggenommen hat. Die vorgestellte Textstelle aus Lombrosos Buch „Neue Fortschritte in den Verbrecherstudien“ ist daher ein besonderes Fundstück auch für die Geschichte der Polygraphie.
Analysis of Miniaturized Printed Flexible RFID/NFC Antennas Using Different Carrier Substrates
(2020)
Antennas for Radio Frequency Identification (RFID) provide benefits for high frequencies (HF) and wireless data transmission via Near Field Communication (NFC) and many other applications. In this case, various requirements for the design of the reader and transmitter antennas must be met in order to achieve a suitable transmission quality. In this work, a miniaturized cost-effective RFID/NFC antenna for a microelectronic measurement system is designed and printed on different flexible carrier substrates using a new and low-cost Direct Ink Writing (DIW) technology. Various practical aspects such as reflection and impedance magnitude as well as the behavior of the printed RFID/NFC antennas are analyzed and compared to an identical copper-based antenna of the same size. The results are presented in this paper. Furthermore, the problems during the printing process itself on the different substrates are evaluated. The effects of the characteristics on the antenna under kink-free bending tests are examined and subsequently long-term measurements are carried out.
Time-Sensitive Networking (TSN) is the most promising time-deterministic wired communication approach for industrial applications. To extend TSN to "IEEE 802.11" wireless networks two challenging problems must be solved: synchronization and scheduling. This paper is focused on the first one. Even though a few solutions already meet the required synchronization accuracies, they are built on expensive hardware that is not suited for mass market products. While next Wi-Fi generation might support the required functionalities, this paper proposes a novel method that makes possible high-precision wireless synchronization using commercial low-cost components. With the proposed solution, a standard deviation of synchronization error of less than 500 ns can be achieved for many use cases and system loads on both CPU and network. This performance is comparable to modern wired real-time field busses, which makes the developed method a significant contribution for the extension of the TSN protocol to the wireless domain.
Diffracted waves carry high‐resolution information that can help interpreting fine structural details at a scale smaller than the seismic wavelength. However, the diffraction energy tends to be weak compared to the reflected energy and is also sensitive to inaccuracies in the migration velocity, making the identification of its signal challenging. In this work, we present an innovative workflow to automatically detect scattering points in the migration dip angle domain using deep learning. By taking advantage of the different kinematic properties of reflected and diffracted waves, we separate the two types of signals by migrating the seismic amplitudes to dip angle gathers using prestack depth imaging in the local angle domain. Convolutional neural networks are a class of deep learning algorithms able to learn to extract spatial information about the data in order to identify its characteristics. They have now become the method of choice to solve supervised pattern recognition problems. In this work, we use wave equation modelling to create a large and diversified dataset of synthetic examples to train a network into identifying the probable position of scattering objects in the subsurface. After giving an intuitive introduction to diffraction imaging and deep learning and discussing some of the pitfalls of the methods, we evaluate the trained network on field data and demonstrate the validity and good generalization performance of our algorithm. We successfully identify with a high‐accuracy and high‐resolution diffraction points, including those which have a low signal to noise and reflection ratio. We also show how our method allows us to quickly scan through high dimensional data consisting of several versions of a dataset migrated with a range of velocities to overcome the strong effect of incorrect migration velocity on the diffraction signal.
Extracting horizon surfaces from key reflections in a seismic image is an important step of the interpretation process. Interpreting a reflection surface in a geologically complex area is a difficult and time-consuming task, and it requires an understanding of the 3D subsurface geometry. Common methods to help automate the process are based on tracking waveforms in a local window around manual picks. Those approaches often fail when the wavelet character lacks lateral continuity or when reflections are truncated by faults. We have formulated horizon picking as a multiclass segmentation problem and solved it by supervised training of a 3D convolutional neural network. We design an efficient architecture to analyze the data over multiple scales while keeping memory and computational needs to a practical level. To allow for uncertainties in the exact location of the reflections, we use a probabilistic formulation to express the horizons position. By using a masked loss function, we give interpreters flexibility when picking the training data. Our method allows experts to interactively improve the results of the picking by fine training the network in the more complex areas. We also determine how our algorithm can be used to extend horizons to the prestack domain by following reflections across offsets planes, even in the presence of residual moveout. We validate our approach on two field data sets and show that it yields accurate results on nontrivial reflectivity while being trained from a workable amount of manually picked data. Initial training of the network takes approximately 1 h, and the fine training and prediction on a large seismic volume take a minute at most.
Printed electronics (PE) enables disruptive applications in wearables, smart sensors, and healthcare since it provides mechanical flexibility, low cost, and on-demand fabrication. The progress in PE raises trust issues in the supply chain and vulnerability to reverse engineering (RE) attacks. Recently, RE attacks on PE circuits have been successfully performed, pointing out the need for countermeasures against RE, such as camouflaging. In this article, we propose a printed camouflaged logic cell that can be inserted into PE circuits to thwart RE. The proposed cell is based on three components achieved by changing the fabrication process that exploits the additive manufacturing feature of PE. These components are optically look-alike, while their electrical behaviors are different, functioning as a transistor, short, and open. The properties of the proposed cell and standard PE cells are compared in terms of voltage swing, delay, power consumption, and area. Moreover, the proposed camouflaged cell is fabricated and characterized to prove its functionality. Furthermore, numerous camouflaged components are fabricated, and their (in)distinguishability is assessed to validate their optical similarities based on the recent RE attacks on PE. The results show that the proposed cell is a promising candidate to be utilized in camouflaging PE circuits with negligible overhead.
Printed electronics (PE) is a fast-growing field with promising applications in wearables, smart sensors, and smart cards, since it provides mechanical flexibility, and low-cost, on-demand, and customizable fabrication. To secure the operation of these applications, true random number generators (TRNGs) are required to generate unpredictable bits for cryptographic functions and padding. However, since the additive fabrication process of the PE circuits results in high intrinsic variations due to the random dispersion of the printed inks on the substrate, constructing a printed TRNG is challenging. In this article, we exploit the additive customizable fabrication feature of inkjet printing to design a TRNG based on electrolyte-gated field-effect transistors (EGFETs). We also propose a printed resistor tuning flow for the TRNG circuit to mitigate the overall process variation of the TRNG so that the generated bits are mostly based on the random noise in the circuit, providing a true random behavior. The simulation results show that the overall process variation of the TRNGs is mitigated by 110 times, and the generated bitstream of the tuned TRNGs passes the National Institute of Standards and Technology - Statistical Test Suite. For the proof of concept, the proposed TRNG circuit was fabricated and tuned. The characterization results of the tuned TRNGs prove that the TRNGs generate random bitstreams at the supply voltage of down to 0.5 V. Hence, the proposed TRNG design is suitable to secure low-power applications in this domain.
Printed Electronics technology is a key-enabler for smart sensors, soft robotics, and wearables. The inkjet printed electrolyte-gated field effect transistor (EGFET) technology is a promising candidate for such applications due to its low-power operation, high field-effect mobility, and on-demand fabrication. Unlike conventional silicon-based technologies, inkjet printed electronics technology is an additive manufacturing process where multiple layers are printed on top of each other to realize functional devices such as transistors and their interconnections. Due to the additive manufacturing process, the technology has limited routing layers. For routing of complex circuits, insulating crossovers are printed at the intersection of routing paths to isolate them. The crossover can alter the electrical properties of a circuit based on specific location on a routing path. In this work, we propose a crossover-aware placement and routing (COPnR) methodology for inkjet-printed circuits by integrating the crossover constraints in our design framework. Our proposed placement methodology is based on a state-of-the-art evolutionary algorithm while the routing optimization is done using a genetic algorithm. The proposed methodology is compared with the industrial standard placement and routing (PnR) tools. On average, the proposed methodology has 38% fewer crossovers and 94% fewer failing paths compared to the industrial PnR tools applied to printed circuit designs.
Advances in printed electronics (PE) enables new applications, particularly in ultra-low-cost domains. However, achieving high-throughput printing processes and manufacturing yield is one of the major challenges in the large-scale integration of PE technology. In this article, we present a programmable printed circuit based on an efficient printed lookup table (pLUT) to address these challenges by combining the advantages of the high-throughput advanced printing and maskless point-of-use final configuration printing. We propose a novel pLUT design which is more efficient in PE realization compared to existing LUT designs. The proposed pLUT design is simulated, fabricated, and programmed as different logic functions with inkjet printed conductive ink to prove that it can realize digital circuit functionality with the use of programmability features. The measurements show that the fabricated LUT design is operable at 1 V.
High-performance Ag–Se-based n-type printed thermoelectric (TE) materials suitable for room-temperature applications have been developed through a new and facile synthesis approach. A high magnitude of the Seebeck coefficient up to 220 μV K–1 and a TE power factor larger than 500 μW m–1 K–2 for an n-type printed film are achieved. A high figure-of-merit ZT ∼0.6 for a printed material has been found in the film with a low in-plane thermal conductivity κF of ∼0.30 W m–1 K–1. Using this material for n-type legs, a flexible folded TE generator (flexTEG) of 13 thermocouples has been fabricated. The open-circuit voltage of the flexTEG for temperature differences of ΔT = 30 and 110 K is found to be 71.1 and 181.4 mV, respectively. Consequently, very high maximum output power densities pmax of 6.6 and 321 μW cm–2 are estimated for the temperature difference of ΔT = 30 K and ΔT = 110 K, respectively. The flexTEG has been demonstrated by wearing it on the lower wrist, which resulted in an output voltage of ∼72.2 mV for ΔT ≈ 30 K. Our results pave the way for widespread use in wearable devices.
Morphological transition of a rod-shaped phase into a string of spherical particles is commonly observed in the microstructures of alloys during solidification (Ratke and Mueller, 2006). This transition phenomenon can be explained by the classic Plateau-Rayleigh theory which was derived for fluid jets based on the surface area minimization principle. The quintessential work of Plateau-Rayleigh considers tiny perturbations (amplitude much less than the radius) to the continuous phase and for large amplitude perturbations, the breakup condition for the rod-shaped phase is still a knotty issue. Here, we present a concise thermodynamic model based on the surface area minimization principle as well as a non-linear stability analysis to generalize Plateau-Rayleigh’s criterion for finite amplitude perturbations. Our results demonstrate a breakup transition from a continuous phase via dispersed particles towards a uniform-radius cylinder, which has not been found previously, but is observed in our phase-field simulations. This new observation is attributed to a geometric constraint, which was overlooked in former studies. We anticipate that our results can provide further insights on microstructures with spherical particles and cylinder-shaped phases.
A Hybrid Optoelectronic Sensor Platform with an Integrated Solution‐Processed Organic Photodiode
(2021)
Hybrid systems, unifying printed electronics with silicon‐based technology, can be seen as a driving force for future sensor development. Especially interesting are sensing elements based on printed devices in combination with silicon‐based high‐performance electronics for data acquisition and communication. In this work, a hybrid system integrating a solution‐processed organic photodiode in a silicon‐based system environment, which enables flexible device measurement and application‐driven development, is presented. For performance evaluation of the integrated organic photodiode, the measurements are compared to a silicon‐based counterpart. Therefore, the steady state response of the hybrid system is presented. Promising application scenarios are described, where a solution‐processed organic photodiode is fully integrated in a silicon system.
Amorphous In-Ga-Zn-O (IGZO) is a high-mobility semiconductor employed in modern thin-film transistors for displays and it is considered as a promising material for Schottky diode-based rectifiers. Properties of the electronic components based on IGZO strongly depend on the manufacturing parameters such as the oxygen partial pressure during IGZO sputtering and post-deposition thermal annealing. In this study, we investigate the combined effect of sputtering conditions of amorphous IGZO (In:Ga:Zn=1:1:1) and post-deposition thermal annealing on the properties of vertical thin-film Pt-IGZO-Cu Schottky diodes, and evaluated the applicability of the fabricated Schottky diodes for low-frequency half-wave rectifier circuits. The change of the oxygen content in the gas mixture from 1.64% to 6.25%, and post-deposition annealing is shown to increase the current rectification ratio from 10 5 to 10 7 at ±1 V, Schottky barrier height from 0.64 eV to 0.75 eV, and the ideality factor from 1.11 to 1.39. Half-wave rectifier circuits based on the fabricated Schottky diodes were simulated using parameters extracted from measured current-voltage and capacitance-voltage characteristics. The half-wave rectifier circuits were realized at 100 kHz and 300 kHz on as-fabricated Schottky diodes with active area of 200 μm × 200 μm, which is relevant for the near-field communication (125 kHz - 134 kHz), and provided the output voltage amplitude of 0.87 V for 2 V supply voltage. The simulation results matched with the measurement data, verifying the model accuracy for circuit level simulation.
Electrolyte-gated thin-film transistors (EGTs) with indium oxide channel, and expected lifetime of three months, enable low-voltage operation (~1 V) in the field of printed electronics (PEs). The channel width of our printed EGTs is varied between 200 and 1000 μm, whereas a channel length between 10 and 100 μm is used. Due to the lack of uniform performance p-type metal oxide semiconductors, n-type EGTs and passive elements are used to design circuits. For logic gates, transistor-resistor logic has been employed so far, but depletion and enhancement-mode EGTs in a transistor-transistor logic boost the circuit performance in terms of delay and signal swing. In this article, the threshold voltage of the EGT, which determines the operation mode, is tuned through sizing of the EGTs channel geometry. The feasibility of both transistor operation modes is demonstrated for logic gates and ring oscillators. An inverter operating at a supply voltage of 1 V shows a maximum gain of 9.6 and a propagation delay time of 0.7 ms, which represents an improvement of ~ 2x for the gain and oscillation frequency, in comparison with the resistor-transistor logic design. Moreover, the power consumption is reduced by 6x.
Fully Printed Inverters using Metal‐Oxide Semiconductor and Graphene Passives on Flexible Substrates
(2020)
Printed and flexible metal‐oxide transistor technology has recently demonstrated great promise due to its high performance and robust mechanical stability. Herein, fully printed inverter structures using electrolyte‐gated oxide transistors on a flexible polyimide (PI) substrate are discussed in detail. Conductive graphene ink is printed as the passive structures and interconnects. The additive printed transistors on PI substrates show an on/off ratio of 106 and show mobilities similar to the state‐of‐the‐art printed transistors on rigid substrates. Printed meander structures of graphene are used as pull‐up resistances in a transistor–resistor logic to create fully printed inverters. The printed and flexible inverters show a signal gain of 3.5 and a propagation delay of 30 ms. These printed inverters are able to withstand a tensile strain of 1.5% following more than 200 cycles of mechanical bending. The stability of the electrical direct current (DC) properties has been observed over a period of 5 weeks. These oxide transistor‐based fully printed inverters are relevant for digital printing methods which could be implemented into roll‐to‐roll processes.
In this report, we have studied field-effect transistors (FETs) using low-density alumina for electrolytic gating. Device layers have been prepared starting from the structured ITO glasses by printing the In 2 O 3 channels, low-temperature atomic layer deposition (ALD) of alumina (Al 2 O 3 ), and printing graphene top gates. The transistor performance could be deliberately changed by alternating the ambient humidity; furthermore, ID,ON/ID,OFF-ratios of up to seven orders of magnitude and threshold voltages between 0.66 and 0.43 V, decreasing with an increasing relative humidity between 40% and 90%, could be achieved. In contrast to the common usage of Al 2 O 3 as the dielectric in the FETs, our devices show electrolyte-typegating behavior. This is a result from the formation of protons on the Al 2 O 3 surfaces at higher humidities. Due to the very high local capacitances of the Helmholtz double layers at the channel surfaces, the operation voltage can be as low as 1 V. At low humidities (≤30%), the solid electrolyte dries out and the performance breaks down; however, it can fully reversibly be regained upon a humidity increase. Using ALD-derived alumina as solid electrolyte gating material, thus, allows low-voltage operation and provides a chemically stable gating material while maintaining low process temperatures. However, it has proven to be highly humidity-dependent in its performance.
In this study, a facile method to fabricate a cohesive ion‐gel based gate insulator for electrolyte‐gated transistors is introduced. The adhesive and flexible ion‐gel can be laminated easily on the semiconducting channel and electrode manually by hand. The ion‐gel is synthesized by a straightforward technique without complex procedures and shows a remarkable ionic conductivity of 4.8 mS cm−1 at room temperature. When used as a gate insulator in electrolyte‐gated transistors (EGTs), an on/off current ratio of 2.24×104 and a subthreshold swing of 117 mV dec−1 can be achieved. This performance is roughly equivalent to that of ink drop‐casted ion‐gels in electrolyte‐gated transistors, indicating that the film‐attachment method might represent a valuable alternative to ink drop‐casting for the fabrication of gate insulators.
Rectifiersare vital electronic circuits for signal and power conversion in various smart sensor applications. The ability to process low input voltage levels, for example, from vibrational energy harvesters is a major challenge with existing passive rectifiers in printed electronics, stemming mainly from the built-in potential of the diode's p-njunction. To address this problem, in this work, we design, fabricate, and characterize an inkjet-printed full-wave rectifier using diode-connected electrolyte-gated thin-film transistors (EGTs). Using both experimental and simulation approaches, we investigate how the rectifier can benefit from the near-zero threshold voltage of transistors, which can be enabled by proper channel geometry setting in EGT technology. The presented circuit can be operated at 1-V input voltage, featuring a remarkably small voltage loss of 140 mV and a cutoff frequency of ~300 Hz. Below the cutoff frequency, more than 2.6-μW dc power is obtained over the load resistances ranging from 5 to 20 kQ. Furthermore, experiments show that the circuit can work with an input amplitude down to 500 mV. This feature makes the presented design highly suitable for a variety of energy-harvesting applications.
Diese Arbeit beschäftigt sich mit der Biomechanik der Halswirbelsäule (HWS) beim Umgang mit dem Smartphone. Die Kräfte, die auf Wirbelkörper, Wirbelgelenke, Bandscheiben, Muskeln und Bänder wirken, werden mit steigendem Flexionswinkel der HWS größer. Die Beschwerden hingegen, welche der Smartphone-Nacken hervorruft, sind meist akut und mit regelmäßiger Bewegung und der Stärkung der Nackenmuskulatur gut zu behandeln. Eine Therapie ist somit auch zur Vorbeugung geeignet. Doch die Langzeitauswirkungen sind nicht außer Acht zu lassen, denn durch die steigenden Nutzungsmöglichkeiten der Smartphones steigt auch der durchschnittliche tägliche Gebrauch stärker an. So wird vor allem die tägliche Bildschirmzeit bei Jugendlichen immer länger. Das aktuell noch akute Krankheitsbild des Smartphone-Nackens, das nur selten einen chronischen Verlauf nimmt und Langzeitschäden verursacht, könnte sich durch fehlende oder zu späte Maßnahmen zu einem größeren chronischen Krankheitsbild entwickeln.
A disturbed synchronization of the ventricular contraction can cause a highly developed systolic heart failure in affected patients with reduction of the left ventricular ejection fraction, which can often be explained by a diseased left bundle branch block (LBBB). If medication remains unresponsive, the concerned patients will be treated with a cardiac resynchronization therapy (CRT) system. The aim of this study was to integrate His-bundle pacing into the Offenburg heart rhythm model in order to visualize the electrical pacing field generated by His-Bundle-Pacing. Modelling and electrical field simulation activities were performed with the software CST (Computer Simulation Technology) from Dessault Systèms. CRT with biventricular pacing is to be achieved by an apical right ventricular electrode and an additional left ventricular electrode, which is floated into the coronary vein sinus. The non-responder rate of the CRT therapy is about one third of the CRT patients. His- Bundle-Pacing represents a physiological alternative to conventional cardiac pacing and cardiac resynchronization. An electrode implanted in the His-bundle emits a stronger electrical pacing field than the electrical pacing field of conventional cardiac pacemakers. The pacing of the Hisbundle was performed by the Medtronic Select Secure 3830 electrode with pacing voltage amplitudes of 3 V, 2 V and 1,5 V in combination with a pacing pulse duration of 1 ms. Compared to conventional pacemaker pacing, His-bundle pacing is capable of bridging LBBB conduction disorders in the left ventricle. The His-bundle pacing electrical field is able to spread via the physiological pathway in the right and left ventricles for CRT with a narrow QRS-complex in the surface ECG.
Bei bimodaler Cochlea-Implantat-/Hörgerät-Versorgung kann es aufgrund seitenverschiedener Signalverarbeitung zu einer zeitlich versetzten Stimulation der beiden Modalitäten kommen. Jüngste Studien haben gezeigt, dass durch zeitlichen Abgleich der Modalitäten die Schalllokalisation bei bimodaler Versorgung verbessert werden kann. Um solch einen Abgleich vornehmen zu können, ist die messtechnische Bestimmung der Durchlaufzeit von Hörgeräten erforderlich. Kommerziell verfügbare Hörgerätemessboxen können diese Werte häufig liefern. Die dazu verwendete Signalverarbeitung wird dabei aber oft nicht vollständig offengelegt. In dieser Arbeit wird ein alternativer und nachvollziehbarer Ansatz zum Design eines simplen Messaufbaus basierend auf einem Arduino DUE Mikrocontroller-Board vorgestellt. Hierzu wurde ein Messtisch im 3D-Druck gefertigt, auf welchem Hörgeräte über einen 2-ccm-Kuppler an ein Messmikrofon angeschlossen werden können. Über einen Latenzvergleich mit dem simultan erfassten Signal eines Referenzmikrofons kann die Durchlaufzeit von Hörgeräten bestimmt werden. Frequenzspezifische Durchlaufzeiten werden mittels einer Kreuzkorrelation zwischen Ziel- und Referenzsignal errechnet. Aufnahme, Ausgabe und Speicherung der Signale erfolgt über einen ATMEL SAM3X8E Mikrocontroller, welcher auf dem Arduino DUE-Board verbaut ist. Über eigens entworfene elektronische Schaltungen werden die Mikrofone und der verwendete Lautsprecher angesteuert. Nach Abschluss einer Messung (Messdauer ca. 5 s) werden die Messdaten seriell an einen PC übertragen, auf dem die Datenauswertung mittels MATLAB erfolgt. Erste Validierungen zeigten eine hohe Stabilität der Messergebnisse mit sehr geringen Standardabweichungen im Bereich weniger Mikrosekunden für Pegel zwischen 50 und 75 dB (A). Der Messaufbau wird in laufenden Studien zur Quantifizierung der Durchlaufzeit von Hörgeräten verwendet.
Im Beitrag wird gezeigt, wie sich die Ackermann’sche Formel zur Polvorgabe bei zeitkontinuierlichen
Ein- und Mehrgrößenzustandsregelungen in einfacher
Weise auf nicht vollständig steuerbare Regelstrecken
erweitern lässt. Das vorgestellte Verfahren basiert
auf einer teilsystemorientierten Zustandstransformation
in Verbindung mit der Einführung zusätzlicher fiktiver Stellgrößen, über die nichtsteuerbare Streckeneigenwerte
formal beeinflusst werden könnten, aber durch Nullsetzen
dieser Stellgrößen nicht beeinflusst werden. Dem
Reglerentwurf vorausgehende Maßnahmen zur Elimination
von nicht steuerbaren Anteilen aus dem Streckenmodell
sind daher nicht erforderlich. Im Vergleich zum Fall
einer vollständig steuerbaren Regelstrecke erfordert die
Anwendung des vorgestellten Verfahrens kaum Mehraufwand,
was am Beispiel eines Eingrößen- und eines Mehrgrößensystems
illustriert wird.
In der vorliegenden Arbeit werden fotografische Aufnahmen zweier verschiedener Abgüsse von Paganinis rechter Hand vorgestellt und näher beschrieben. Es handelt sich um einen mutmaßlich originalen Bronzeabguss, der vermutlich kurz nach Paganinis Tod auf dessen Totenbett abgenommen wurde, und eine in heutiger Zeit angefertigte Kopie aus Fiberplastik mit goldfarbenem Anstrich. Die Hand ist im proximalen Handgelenk stark abgewinkelt, was dafür spricht, dass die Hand des Toten auf einem Kissen gelegen haben könnte, um den Abguss vorzunehmen. Überdies zeigt sich eine verkrampfte Stellung der Finger und Hand, am ehesten infolge Totenstarre. Man findet zudem arthrotische Veränderungen sowie hervortretende Sehnen und atrophierte Muskulatur. Beim Bronzeabguss sind die beschriebenen Auffälligkeiten deutlicher zu erkennen. Ein 3D-Scan des Bronzeabgusses der rechten Hand Paganinis mit einem Strukturlichtscanner würde die Möglichkeit eröffnen, Messdaten der Hand zu erhalten.
In der vorliegenden Arbeit wurde die von Wilhelm His Sr. angefertigte und im Jahr 1895 publizierte Fotografie des mutmaßlichen Skeletts von Johann Sebastian Bach auf ihre Abbildungsqualität untersucht. Dies erfolgte durch direkte Messungen an einem digitalen Scan der Fotografie. Dabei wurde der von His der Fotografie beigelegte Lineal-Maßstab in mehrere 10-cm-Stücke unterteilt und die Länge dieser Abschnitte im Digitalisat mit dem Messinstrument von Adobe Acrobat ausgemessen. Darüber hinaus wurden die Längen der Femora ermittelt und mit den Maßen verglichen, die 1895 an den tatsächlichen (realen) Knochen ermittelt wurden. In dem Digitalisat entsprachen 190 cm im Lineal 244,48 mm. Der Mittelwert der 19 bestimmten 10-cm-Abschnitte betrug 100,49 mm (Median 100,49 mm, Standardabweichung 0,49 mm). Die historische Femurlänge links betrug 443,5 mm, rechts 451,0 mm. Die im Digitalisat ermittelte Femurlänge betrug links 443,8 mm, rechts 451,1 mm. Zusätzlich wurden die projizierten Centrum-Collum-Diaphysen-Winkel bestimmt. Die Daten lassen den Schluss zu, dass die Oben/unten-Verzerrung sowie die Rechts/links-Verzerrung nicht nennenswert sind und das von His angefertigte Foto mit einer hohen Genauigkeit der Abbildungsqualität und des Linsenapparats der Kamera angefertigt wurde, die es ermöglicht, bestimmte Skelettanteile aussagekräftig zu beurteilen und auszumessen.
Neurostimulation durch Musik
(2020)
Was ist die Musik und wie wirkt sie sich auf den menschlichen Körper aus? Historisch betrachtet wird die Musik als etwas Göttliches aufgefasst, da sie eine äußerst große Wirkung auf die Emotionen des Menschen besitzt. Dieser Effekt wirkt sich auch psychosomatisch aus und kann das Denken und Handeln des Zuhörers beeinflussen und steuern. So lässt sich beispielsweise das Kaufverhalten allein durch die musikalische Begleitung deutlich manipulieren. Selbst die Motivation lässt sich mit passender Vertonung entweder steigern oder reduzieren. In der heutigen Zivilisation begleitet die Musik den Menschen alltäglich und wird zu vielen verschiedenen Zwecken verwendet. Somit ist die musikalische Stimulation als eine Art Psychotherapie zu werten, die häufig gezielt angewendet wird, aber im Beeinflussten unterbewusst stattfindet. Da natürlich immer noch offene Fragen bezüglich der genauen Wirkung von Musik auf das Gehirn bestehen, werden derzeit im Bereich der Neurowissenschaften viele Studien durchgeführt, um dieses Phänomen nachvollziehen zu können.
Finding clusters in high dimensional data is a challenging research problem. Subspace clustering algorithms aim to find clusters in all possible subspaces of the dataset, where a subspace is a subset of dimensions of the data. But the exponential increase in the number of subspaces with the dimensionality of data renders most of the algorithms inefficient as well as ineffective. Moreover, these algorithms have ingrained data dependency in the clustering process, which means that parallelization becomes difficult and inefficient. SUBSCALE is a recent subspace clustering algorithm which is scalable with the dimensions and contains independent processing steps which can be exploited through parallelism. In this paper, we aim to leverage the computational power of widely available multi-core processors to improve the runtime performance of the SUBSCALE algorithm. The experimental evaluation shows linear speedup. Moreover, we develop an approach using graphics processing units (GPUs) for fine-grained data parallelism to accelerate the computation further. First tests of the GPU implementation show very promising results.
In many application domains, in particular automotives, guaranteeing a very low failure rate is crucial to meet functional and safety standards. Especially, reliable operation of memory components such as SRAM cells is of essential importance. Due to aggressive technology downscaling, process and runtime variations significantly impact manufacturing yield as well as functionality. For this reason, a thorough memory failure rate assessment is imperative for correct circuit operation and yield improvement. In this regard, Monte Carlo simulations have been used as the conventional method to estimate the variability induced failure rate of memory components. However, Monte Carlo methods become infeasible when estimating rare events such as high-sigma failure rates. To this end, Importance Sampling methods have been proposed which reduce the number of required simulations substantially. However, existing methods still suffer from inaccuracies and high computational efforts, in particular for high-sigma problems. In this paper, we fill this gap by presenting an efficient mixture Importance Sampling approach based on Bayesian optimization, which deploys a surface model of the objective function to find the most probable failure points. Its advantages include constant complexity independent of the dimensions of design space, the potential to find the global extrema, and higher trustworthiness of the estimated failure rate by accurately exploring the design space. The approach is evaluated on a 6T-SRAM cell as well as a master-slave latch based on a 28nm FDSOI process. The results show an improvement in accuracy, resulting in up to 63× better accuracy in estimating failure rates compared to the best state-of-the-art solutions on a 28nm technology node.
Oxide semiconductors have the potential to increase the performance of inkjet printed microelectronic devices such as field-effect transistors (FETs), due to their high electron mobilities. Typical metal oxides are n-type semiconductors, while p-type oxides, although realizable, exhibit lower carriermobilities. Therefore, the circuit design based on oxide semiconductors is mostly in n-type logic only. Here we present an inkjet printed pn-diode based on p- and n-type oxide semiconductors.Copper oxide or nickel oxide is used as p-typesemiconductor whereas n-typesemiconductor is realized with indium oxide. Themeasurements show that the pn-diodes operate in the voltage window typical for printed electronics and the emission coefficient is 1.505 and 2.199 for the copper oxide based and nickel oxidebased pn-diode, respectively.Furthermore, a pn-diode model is developed and integrable into a circuit simulator.
Printed systems spark immense interest in industry, and for several parts such as solar cells or radio frequency identification antennas, printed products are already available on the market. This has led to intense research; however, printed field-effect transistors (FETs) and logics derived thereof still have not been sufficiently developed to be adapted by industry. Among others, one of the reasons for this is the lack of control of the threshold voltage during production. In this work, we show an approach to adjust the threshold voltage (Vth) in printed electrolyte-gated FETs (EGFETs) with high accuracy by doping indium-oxide semiconducting channels with chromium. Despite high doping concentrations achieved by a wet chemical process during precursor ink preparation, good on/off-ratios of more than five orders of magnitude could be demonstrated. The synthesis process is simple, inexpensive, and easily scalable and leads to depletion-mode EGFETs, which are fully functional at operation potentials below 2 V and allows us to increase Vth by approximately 0.5 V.
Development of Fully Printed Oxide Field-Effect Transistors using Graphene Passive Structures
(2019)
During the past decade to the present time, the topic of printed electronics has gained a lot of attention for their potential use in a number of practical applications, including biosensors, photovoltaic devices, RFIDs, flexible displays, large-area circuits, and so on. To fully realize printed electronic components and devices, effective techniques for the printing of passive structures and electrically and chemically compatible materials in the printed devices need to be developed first. The opportunity of using electrically conducting graphene inks will enable the integration of passive structures into active devices, as for example, printed electrolyte-gated transistors (EGTs). Accordingly, in this study, we present the parametric results obtained on fully printed electrolyte-gated transistors having graphene as the passive electrodes, an inorganic oxide semiconductor as the active channel, and a composite solid polymer electrolyte (CSPE) as the gate insulating material. This configuration offers high chemical and electrical stability while at the same time allowing EGT operation at low potentials, implying the distinct advantage of operation at low input voltages. The printed in-plane EGTs we developed exhibit excellent performance with device mobility up to 16 cm2 V–1 s–1, an ION/IOFF ratio of 105, and a subthreshold slope of 120 mV dec–1.
Printed electronics (PE) circuits have several advantages over silicon counterparts for the applications where mechanical flexibility, extremely low-cost, large area, and custom fabrication are required. The custom (personalized) fabrication is a key feature of this technology, enabling customization per application, even in small quantities due to low-cost printing compared with lithography. However, the personalized and on-demand fabrication, the non-standard circuit design, and the limited number of printing layers with larger geometries compared with traditional silicon chip manufacturing open doors for new and unique reverse engineering (RE) schemes for this technology. In this paper, we present a robust RE methodology based on supervised machine learning, starting from image acquisition all the way to netlist extraction. The results show that the proposed RE methodology can reverse engineer the PE circuits with very limited manual effort and is robust against non-standard circuit design, customized layouts, and high variations resulting from the inherent properties of PE manufacturing processes.
Printed electrolyte-gated oxide electronics is an emerging electronic technology in the low voltage regime (≤1 V). Whereas in the past mainly dielectrics have been used for gating the transistors, many recent approaches employ the advantages of solution processable, solid polymer electrolytes, or ion gels that provide high gate capacitances produced by a Helmholtz double layer, allowing for low-voltage operation. Herein, with special focus on work performed at KIT recent advances in building electronic circuits based on indium oxide, n-type electrolyte-gated field-effect transistors (EGFETs) are reviewed. When integrated into ring oscillator circuits a digital performance ranging from 250 Hz at 1 V up to 1 kHz is achieved. Sequential circuits such as memory cells are also demonstrated. More complex circuits are feasible but remain challenging also because of the high variability of the printed devices. However, the device inherent variability can be even exploited in security circuits such as physically unclonable functions (PUFs), which output a reliable and unique, device specific, digital response signal. As an overall advantage of the technology all the presented circuits can operate at very low supply voltages (0.6 V), which is crucial for low-power printed electronics applications.
Electrolyte-gated, printed field-effect transistors exhibit high charge carrier densities in the channel and thus high on-currents at low operating voltages, allowing for the low-power operation of such devices. This behavior is due to the high area-specific capacitance of the device, in which the electrolyte takes the role of the dielectric layer of classical architectures. In this paper, we investigate intrinsic double-layer capacitances of ink-jet printed electrolyte-gated inorganic field-effect transistors in both in-plane and top-gate architectures by means of voltage-dependent impedance spectroscopy. By comparison with deembedding structures, we separate the intrinsic properties of the double-layer capacitance at the transistor channel from parasitic effects and deduce accurate estimates for the double-layer capacitance based on an equivalent circuit fitting. Based on these results, we have performed simulations of the electrolyte cutoff frequency as a function of electrolyte and gate resistances, showing that the top-gate architecture has the potential to reach the kilohertz regime with proper optimization of materials and printing process. Our findings additionally enable accurate modeling of the frequency-dependent capacitance of electrolyte/ion gel-gated devices as required in the small-signal analysis in the circuit simulation.
In the domain of printed electronics (PE), field-effect transistors (FETs) with an oxide semiconductor channel are very promising. In particular, the use of high gate-capacitance of the composite solid polymer electrolytes (CSPEs) as a gate-insulator ensures extremely low voltage requirements. Besides high gate capacitance, such CSPEs are proven to be easily printable, stable in air over wide temperature ranges, and possess high ion conductivity. These CSPEs can be sensitive to moisture, especially for high surface-to-volume ratio printed thin films. In this paper, we provide a comprehensive experimental study on the effect of humidity on CSPE-gated single transistors. At the circuit level, the performance of ring oscillators (ROs) has been compared for various humidity conditions. The experimental results of the electrolyte-gated FETs (EGFETs) demonstrate rather comparable currents between 30%-90% humidity levels. However, the shifted transistor parameters lead to a significant performance change of the RO frequency behavior. The study in this paper shows the need of an impermeable encapsulation for the CSPE-gated FETs to ensure identical performance at all humidity conditions.
Printed electronics can benefit from the deployment of electrolytesas gate insulators,which enables a high gate capacitance per unit area (1–10 μFcm−2) due to the formation of electrical double layers (EDLs). Consequently, electrolyte-gated field-effect transistors (EGFETs) attain high-charge carrier densities already in the subvoltage regime, allowing for low-voltage operation of circuits and systems. This article presents a systematic study of lumped terminal capacitances of printed electrolyte-gated transistors under various dc bias conditions. We perform voltage-dependent impedancemeasurements and separate extrinsic components from the lumped terminal capacitance.
The proposed Meyer-like capacitance model, which also accounts for the nonquasi-static (NQS) effect, agrees well with experimental data. Finally, to verify the model, we implement it in Verilog-A and simulate the transient response of an inverter and a ring oscillator circuit. Simulation results are in good agreement with the measurement data of fabricated devices.
A physical unclonable function (PUF) is a hardware circuit that produces a random sequence based on its manufacturing-induced intrinsic characteristics. In the past decade, silicon-based PUFs have been extensively studied as a security primitive for identification and authentication. The emerging field of printed electronics (PE) enables novel application fields in the scope of the Internet of Things (IoT) and smart sensors. In this paper, we design and evaluate a printed differential circuit PUF (DiffC-PUF). The simulation data are verified by Monte Carlo analysis. Our design is highly scalable while consisting of a low number of printed transistors. Furthermore, we investigate the best operating point by varying the PUF challenge configuration and analyzing the PUF security metrics in order to achieve high robustness. At the best operating point, the results show areliability of 98.37% and a uniqueness of 50.02%, respectively. This analysis also provides useful and comprehensive insights into the design of hybrid or fully printed PUF circuits. In addition, the proposed printed DiffC-PUF core has been fabricated with electrolyte-gated field-effect transistor technology to verify our design in hardware.
Im Beitrag wird für lineare, zeitinvariante, zeitdiskrete und stabile Regelstrecken beschrieben, wie zwei bekannte Zustandsraumverfahren zur Windup-Vermeidung so miteinander kombiniert werden können, dass dadurch für sämtliche PI-Zustandsregler Strecken- und Regler-Windup verhindert wird, sofern diese Regler im unbegrenzten Fall stabil sind. Zurückgegriffen wird hierbei auf das „Additional Dynamic Element“ (ADE) von Hippe zur Vermeidung von Strecken-Windup [Hippe, P.: Windup in control – Its effects and their prevention, 2006; at – Automatisierungstechnik, 2007], dessen Übertragung auf zeitdiskrete Systeme im Beitrag kurz skizziert wird, sowie auf das Verfahren der Führungsgrößenkorrektur [Nuß, U.: at – Automatisierungstechnik, 2017] zur Vermeidung von Regler-Windup. Das vorgestellte Kombinationsverfahren setzt für die jeweilige Regelstrecke lediglich die Einbeziehung eines bereits existierenden P-Zustandsreglers voraus, der Strecken-Windup vermeidet. Die Bereitstellung eines möglichst einfachen und dennoch nicht allzu einschränkenden Kriteriums zur Überprüfung, ob ein P-Zustandsregler diese Eigenschaft besitzt, ist ebenfalls ein Anliegen des Beitrags. Diesbezüglich wird auf der Basis einer geeigneten Ljapunow-Funktion ein hinreichendes Kriterium angegeben, das umfassender ist als das in [Nuß, U.: at – Automatisierungstechnik, 2017] verwendete. Ein Beispiel aus der elektrischen Antriebstechnik demonstriert die Leistungsfähigkeit der vorgestellten Methode.
In users of a cochlear implant (CI) together with a contralateral hearing aid (HA), so-called bimodal listeners, differences in processing latencies between digital HA and CI up to 9 ms constantly superimpose interaural time differences. In the present study, the effect of this device delay mismatch on sound localization accuracy was investigated. For this purpose, localization accuracy in the frontal horizontal plane was measured with the original and minimized device delay mismatch. The reduction was achieved by delaying the CI stimulation according to the delay of the individually worn HA. For this, a portable, programmable, battery-powered delay line based on a ring buffer running on a microcontroller was designed and assembled. After an acclimatization period to the delayed CI stimulation of 1 hr, the nine bimodal study participants showed a highly significant improvement in localization accuracy of 11.6% compared with the everyday situation without the delay line (p < .01). Concluding, delaying CI stimulation to minimize the device delay mismatch seems to be a promising method to increase sound localization accuracy in bimodal listeners.
The visualization of heart rhythm disturbance and atrial fibrillation therapy allows the optimization of new cardiac catheter ablations. With the simulation software CST (Computer Simulation Technology, Darmstadt) electromagnetic and thermal simulations can be carried out to analyze and optimize different heart rhythm disturbance and cardiac catheters for pulmonary vein isolation. Another form of visualization is provided by haptic, three-dimensional print models. These models can be produced using an additive manufacturing method, such as a 3d printer. The aim of the study was to produce a 3d print of the Offenburg heart rhythm model with a representation of an atrial fibrillation ablation procedure to improve the visualization of simulation of cardiac catheter ablation. The basis of 3d printing was the Offenburg heart rhythm model and the associated simulation of cryoablation of the pulmonary vein. The thermal simulation shows the pulmonary vein isolation of the left inferior pulmonary vein with the cryoballoon catheter Arctic Front Advance™ from Medtronic. After running through the simulation, the thermal propagation during the procedure was shown in the form of different colors. The three-dimensional print models were constructed on the base of the described simulation in a CAD program. Four different 3d printers are available for this purpose in a rapid prototyping laboratory at the University of Applied Science Offenburg. Two different printing processes were used and a final print model with additional representation of the esophagus and internal esophagus catheter was also prepared for printing. With the help of the thermal simulation results and the subsequent evaluation, it was possible to draw a conclusion about the propagation of the cold emanating from the catheter in the myocardium and the surrounding tissue. It was measured that just 3 mm from the balloon surface into the myocardium the temperature dropped to 25 °C. The simulation model was printed using two 3d printing methods. Both methods, as well as the different printing materials offer different advantages and disadvantages. All relevant parts, especially the balloon catheter and the conduction, are realistically represented. Only the thermal propagation in the form of different colors is not shown on this model. Three-dimensional heart rhythm models as well as virtual simulations allow very clear visualization of complex cardiac rhythm therapy and atrial fibrillation treatment methods. The printed models can be used for optimization and demonstration of cryoballoon catheter ablation in patients with atrial fibrillation.
Spinal cord stimulation (SCS) is the most commonly used technique of neurostimulation. It involves the stimulation of the spinal cord and is therefore used to treat chronic pain. The existing esophageal catheters are used for temperature monitoring during an electrophysiology study with ablation and transesophageal echocardiography. The aim of the study was to model the spine and new esophageal electrodes for the transesophageal electrical pacing of the spinal cord, and to integrate them in the Offenburg heart rhythm model for the static and dynamic simulation of transesophageal neurostimulation. The modeling and simulation were both performed with the electromagnetic and thermal simulation software CST (Computer Simulation Technology, Darmstadt). Two new esophageal catheters were modelled as well as a thoracic spine based on the dimensions of a human skeleton. The simulation of directed transesophageal neurostimulation is performed using the esophageal balloon catheter with an electric pacing potential of 5 V and a trapezoidal signal. A potential of 4.33 V can be measured directly at the electrode, 3.71 V in the myocardium at a depth of 2 mm, 2.68 V in the thoracic vertebra at a depth of 10 mm, 2.1 V in the thoracic vertebra at a depth of 50 mm and 2.09 V in the spinal cord at a depth of 70 mm. The relation between the voltage delivered to the electrodes and the voltage applied to the spinal cord is linear. Virtual heart rhythm and catheter models as well as the simulation of electrical pacing fields and electrical sensing fields allow the static and dynamic simulation of directed transesophageal electrical pacing of the spinal cord. The 3D simulation of the electrical sensing and pacing fields may be used to optimize transesophageal neurostimulation.
In this paper pathophysiological interrelated deactivation/activation phenomena are set out in the example of whiplash injury. These phenomena could have been underestimated in previous positron emission tomography studies as their focus was on hypoperfusion rather than hyperperfusion. In addition, statistical parametric mapping analysis of cerebral studies is normally not fine-tuned to special interesting areas rather than to obvious clusters of difference.