Refine
Document Type
Conference Type
- Sonstiges (4)
- Konferenzartikel (3)
Has Fulltext
- no (8)
Is part of the Bibliography
- yes (8)
Keywords
- RoboCup (4)
- Elektromotor (1)
- Humanoider Roboter (1)
- Leichtbau (1)
- Radnabenmotor (1)
- Roboter (1)
- Sensortechniik (1)
- Stadtfahrzeug (1)
Institute
- Fakultät Elektrotechnik und Informationstechnik (E+I) (bis 03/2019) (8) (remove)
Open Access
- Open Access (7)
- Bronze (5)
- Closed Access (1)
Das Ingenieurbüro Evomotiv GmbH und die University of Applied Sciences Offenburg entwickeln seit Ende 2008 ein Antriebskonzept für leichte Stadtfahrzeuge. Ziel des Elektroantriebs ist die Serientauglichkeit der hochintegrierten, getriebelosen und eisenfreien Radnabenmotoren. Das Bundesministerium für Wirtschaft und Technologie (BMWi) unterstützt das Projekt. Das Konzept des Radnabenmotors erhielt 2006 den Bosch—Innovationspreis und gewann 2008 den Shell-Eco-Marathon. Im Jahr 2011 wird Evomotiv mit seinen Partnern erste Prototypen auf der Straße testen.
Autonomous humanoid robots need high torque actuators to be able to walk and run. One problem in this context is the heat generated. In this paper we propose to use water evaporation to improve cooling of the motors. Simulations based on thermodynamic calculations as well as measurements on real actuators show that, under the assumption of the load of a soccer game, cooling can be considerably improved with relatively small amounts of water.
This paper describes the new Sweaty humanoid adult size robot trying to qualify for the RoboCup 2014 adult size humanoid competition. The robot is built from scratch to eventually allow it to run. One characteristic is that to prevent the motors from overheating, water evaporation is used for cooling. The robot is literally sweating which has given it its name. Another characteristic is, that the motors are not directly connected to the frame but by means of beams. This allows a variable transmission ratio depending on the angle.
Autonomous humanoid robots require light weight, high torque and high speed actuators to be able to walk and run. For conventional gears with a fixed gear ratio the product of torque and velocity is constant. On the other hand desired motions require maximum torque and speed. In this paper it is shown that with a variable gear ratio it is possible to vary the relation between torque and velocity. This is achieved by introducing systems of rods and levers to move the joints of our humanoid robot ”Sweaty II”. On the basis of a variable gear ratio low speed and high torque can be achieved for those joint angles, which require this motion mode, whereas high speed and low torque can be realized for those joint angles, where it is favorable for the desired motion.
This paper describes the new Sweaty II humanoid adult size robot trying to qualify for the RoboCup 2016 adult size humanoid competition. Based on experiences during RoboCup 2014, the Sweaty robot has been completely redesigned to a new robot Sweaty II. A major change is the use of linear actuators for the legs. Another characteristic is its indirect actuation by means of rods. This allows a variable transmission ratio depending on the angle of a joint.
The humanoid Sweaty was the finalist in this year’s robocup soccer championship(adult size). For the optimization of the gait and the stability, data concerning forces and torques in the ankle joints would be helpful. In the following paper the development of a six-axis force and torque sensor for the humanoid robot Sweaty is described. Since commercial sensors do not meet the demands for the sensors in Sweatys ankle joints, a new sensor was developed. As a measuring devices we used strain gauges and custom electronics based on an acam PS09. The geometry was analyzed with the FEM program ANSYS to get optimal dimensions for the measuring beams. In addition ANSYS was used to optimize the position for the strain gauges on the beam.
This paper describes the Sweaty II humanoid adult size robot trying to qualify for the RoboCup 2017 adult size humanoid competition. Sweaty came 2nd in RoboCup 2016 adult size league. The paper describes the main characteristics of Sweaty that made this success possible, and improvements that have been made or are planned to be implemented for RoboCup 2017.
This paper describes the Sweaty II humanoid adult size robot trying to qualify for the RoboCup 2018 adult size humanoid competition. Sweaty came 2nd in RoboCup 2017 adult size league. The main characteristics of Sweaty are described in the Team Description Paper 2017. The improvements that have been made or are planned to be implemented for RoboCup 2018 are described in this paper.