Refine
Year of publication
Document Type
- Article (reviewed) (25)
- Conference Proceeding (12)
- Article (unreviewed) (3)
- Report (2)
- Part of a Book (1)
Conference Type
- Konferenzartikel (12)
Has Fulltext
- no (43) (remove)
Is part of the Bibliography
- yes (43)
Keywords
- Plastizität (10)
- Ermüdung (9)
- Mikrostruktur (6)
- Stahl (5)
- Eisenguss (4)
- Materialermüdung (4)
- Simulation (4)
- Thermomechanik (4)
- Finite-Elemente-Methode (3)
- Rissausbreitung (3)
Institute
Open Access
- Closed Access (20)
- Closed (9)
- Open Access (9)
- Diamond (1)
Turbocharger housings in internal combustion engines are subjected to severe mechanical and thermal cyclic loads throughout their life-time or during engine testing. The combination of thermal transients and mechanical load cycling results in a complex evolution of damage, leading to thermo-mechanical fatigue (TMF) of the material. For the computational TMF life assessment of high temperature components, the DTMF model can provide reliable TMF life predictions. The model is based on a short fatigue crack growth law and uses local finite-element (FE) results to predict the number of cycles to failure for a technical crack. In engine applications, it is nowadays often acceptable to have short cracks as long as they do not propagate and cause loss of function of the component. Thus, it is necessary to predict not only potential crack locations and the corresponding number of cycles for a technical crack, but also to determine subsequent crack growth or even a possible crack arrest. In this work, a method is proposed that allows the simulation of TMF crack growth in high temperature components using FE simulations and non-linear fracture mechanics (NLFM).
A NLFM based crack growth simulation method is described. This method starts with the FE analysis of a component. In this paper, the method is demonstrated for an automotive turbocharger housing subjected to TMF loading. A transient elastic-viscoplastic FE analysis is used to simulate four heating and cooling cycles of an engine test. The stresses, inelastic strains, and temperature histories from the FEA are then used to perform TMF life predictions using the standard DTMF model. The crack position and the crack plane of critical hotspots are then identified. Simulated cracks are inserted at the hotspots. For the model demonstrated, cracks were inserted at two hotspot locations. The ΔJ integral is computed as a fracture mechanics parameter at each point along the crack-front, and the crack extension of each point is then evaluated, allowing the crack to grow iteratively. The paper concludes with a comparison of the crack growth curves for both hotspots with experimental results.
Cast aluminum cylinder blocks are frequently used in gasoline and diesel internal combustion engines because of their light-weight advantage. However, the disadvantage of aluminum alloys is their relatively low strength and fatigue resistance which make aluminum blocks prone to fatigue cracking. Engine blocks must withstand a combination of low-cycle fatigue (LCF) thermal loads and high-cycle fatigue (HCF) combustion and dynamic loads. Reliable computational methods are needed that allow for accurate fatigue assessment of cylinder blocks under this combined loading. In several publications, the mechanism-based thermomechanical fatigue (TMF) damage model DTMF describing the growth of short fatigue cracks has been extended to include the effect of both LCF thermal loads and superimposed HCF loadings. This approach is applied to the finite life fatigue assessment of an aluminum cylinder block. The required material properties related to LCF are determined from uniaxial LCF tests. The additional material properties required for the assessment of superimposed HCF are obtained from the literature for similar materials. The predictions of the model agree well with engine dyno test results. Finally, some improvements to the current process are discussed.
In this paper, the J-integral is derived for temperature-dependent elastic–plastic materials described by incremental plasticity. It is implemented using the equivalent domain integral method for assessment of three-dimensional cracks based on results of finite-element calculations. The J-integral considers contributions from inhomogeneous temperature fields and temperature-dependent elastic and plastic material properties as well as from gradients in the plastic strains and the hardening variables. Different energy densities are considered, the Helmholtz free energy and the stress-working density, providing a physical meaning of the J-integral as a fracture criteria for crack growth. Results obtained for a plate with two different crack configurations each loaded by a cool-down thermal shock show domain-independence of the incremental J-integral for different energy densities even for high temperature gradients and significant temperature-dependence of the yield stress and the hardening exponent in the presence of large scale yielding. Hence, the derived J-integral is an appropriate parameter for the assessment of cracks in thermomechanically loaded components.
Für langfaserverstärkte Thermoplaste (LFT) wird ein repräsentatives Volumenelement (RVE) für FEM-Simulationen generiert. Dies geschieht unter Berücksichtigung von mikrostrukturellen Kenngrößen wie Faserorientierungsverteilung, -volumengehalt und -längenverteilung, die für einen charakteristischen Werkstoffzustand experimentell ermittelt wurden. Mittels Mikrostruktursimulationen wird das Kriechverhalten von LFT untersucht. Das viskoelastische Verhalten der Matrix wird experimentell an Substanzproben aus Polypropylen ermittelt und in die RVE-Simulationen mit einem modifizierten Burgers-Modell implementiert. Schließlich werden die Rechnungen mit verschiedenen, fiktiven sowie experimentell ermittelten Faserlängenverteilungen mit Kriechversuchen am LFT verglichen. Es zeigt sich eine starke Abhängigkeit des Kriechverhaltens von der Faserlänge und eine hohe Prognosegüte der Simulationen, die die experimentell ermittelte Längenverteilung berücksichtigen.
Hot forging dies are subjected to high cyclic thermo-mechanical loads. In critical areas, the occurring stresses can exceed the material’s yield limit. Additionally, loading at high temperatures leads to thermal softening of the used martensitic materials. These effects can result in an early crack initiation and unexpected failure of the dies, usually described as thermo-mechanical fatigue (TMF). In previous works, a temperature-dependent cyclic plasticity model for the martensitic hot forging tool steel 1.2367 (X38CrMoV5-3) was developed and implemented in the finite element (FE)-software Abaqus. However, in the forging industry, application-specific software is usually used to ensure cost-efficient numerical process design. Therefore, a new implementation for the FE-software Simufact Forming 16.0 is presented in this work. The results are compared and validated with the original implementation by means of a numerical compression test and a cyclic simulation is calculated with Simufact Forming.
Significant improvements in module performance are possible via implementation of multi-wire electrodes. This is economically sound as long as the mechanical yield of the production is maintained. While flat ribbons have a relatively large contact area to exert forces onto the solar cell, wires with round cross section reduce this contact area considerably – in theory to an infinitively thin line. Therefore, the local stresses induced by the electrodes might increase to a point that mechanical production yields suffer unacceptably.
In this paper, we assess this issue by an analytical mechanical model as well as experiments with an encapsulant-free N.I.C.E. test setup. From these, we can derive estimations for the relationship between lay-up accuracy and expected breakage losses. This paves the way for cost-optimized choices of handling equipment in industrial N.I.C.E.-wire production lines.
In this work, time-independent and time-dependent plasticity models are presented that are well suited for the calculation of stresses and strains with the finite-element method to assess the low-cycle and thermomechanical fatigue life of engineering components. The focus are plasticity models that are available in finite-element programs nowadays as standard material models and describe isotropic and kinematic hardening, strain-rate dependency as well as static recovery of hardening. For the presented models, aspects relevant for the application of the models are addressed as the determination of the material properties and the numerical implementation. Nevertheless, the plasticity models are also embedded in the thermodynamic framework used for the derivation of thermodynamically consistent plasticity models. Only uniaxial formulations are used to achieve a good readability and preventing the use of tensors.
In this paper, the influence of the material hardening behavior on plasticity-induced fatigue crack closure is investigated for strain-controlled loading and fully plastic, large-scale yielding conditions by means of the finite element method. The strain amplitude and the strain ratio are varied for given Ramberg–Osgood material properties representing materials with different hardening behavior. The results show a pronounced influence of the hardening behavior on crack closure, while no significant effect is found from the considered strain amplitude and strain ratio. The effect of the hardening behavior on the crack opening stress cannot be described by existing crack opening stress equations.
In this paper, the effect of the polycrystalline microstructure on crack-tip opening displacement and crack closure is investigated for microstructural short plane strain fatigue cracks using the finite-element method. To this end, cracks are introduced in synthetically generated microstructures and the grain properties are described using a single crystal plasticity model with kinematic hardening. Additionally, finite-element calculations without resolved microstructure and von Mises plasticity with kinematic hardening are performed. Fully-reversed strain-controlled cyclic loadings are considered under large-scale yielding conditions as typical for low-cycle fatigue problems. The crack opening stress and the cyclic crack-tip opening displacement are significantly influenced by the local grain structure. While the stabilized crack opening stresses obtained with the microstructure-based finite-element model are in good accordance with the von Mises plasticity results, the differences in the cyclic crack opening displacement are addressed to the asymmetric plastic strain fields in the plastic wake behind the crack-tip of the microstructure-based model. The asymmetric plastic strain fields result in discontinuous and premature contact of the crack flanks.
The work focuses on predictive capabilities of fundamental cyclic plasticity and fatigue life models, which can be calibrated using limited amount of experiments as specific ones needed for more advanced models are often absent. The analyses are conducted for the synthetic case of exhaust manifold made from cast iron. The thermal boundary conditions from the forced convection were obtained from the computational fluid dynamics considered as a conjugate heat transfer problem. Two rate-independent and temperature-dependent material models were calibrated for structural analyses. Both were validated with experiments on isothermal and anisothermal levels. Sequential thermal–mechanical finite element simulations were performed. Two fatigue life models were employed. The first was a temperature-dependent strain-based fatigue life criterion calibrated from uniaxial data. The second was a temperature-independent energy-based fatigue life criterion resulting in twice lower life than the strain-based criterion, while none of the plasticity models made a significant difference in that prediction.
Due to higher combustion chamber temperatures and pressures in efficient combustion engines, both the high-cycle and thermomechanical fatigue loads on service life-critical components, such as the cylinder head, are increasing. Material comparisons and analysis of damage behavior are very expensive and time-consuming using component tests. This study therefore develops a test method for cylinder head materials that takes into account the combined loading conditions from the above-mentioned loads and allows realistic temperature transients and gradients on near-component samples. The near-component cylinder head sample represents the failure-critical exhaust valve crosspiece and is tested in a test rig specially designed with the aid of conjugate heat transfer simulations. In the test rig, the sample is subjected to thermal stress by a hot gas burner and to mechanical stress by a high-frequency pulsator. Optical crack detection allows permanent observation of fatigue crack growth and crack closure during the test. Fractographic and metallo-graphic examinations of the fracture areas as well as analyses of the damage patterns show that loads close to engine operation can be set in this way and their influences on the damage can be monitored.
In order to make material design processes more efficient in the future, the underlying multidimensional process parameter spaces must be systematically explored using digitalisation techniques such as machine learning (ML) and digital simulation. In this paper we shortly review essential concepts for the digitalisation of electrodeposition processes with a special focus on chromium plating from trivalent electrolytes.
In this paper, the Bauschinger effect and latent hardening of single crystals are assessed in finite element calculations using a single crystal plasticity model with kinematic hardening. To this end, results of cyclic micro-bending experiments on single crystal Alloy 718 in different crystal orientations (single slip and multi slip) with respect to the loading direction are used to determine the slip system related material properties of the single crystal plasticity model. Two kinematic hardening laws are considered: a kinematic hardening law describing latent hardening and a kinematic hardening law without latent hardening. For the determination of material properties for both hardening laws, a gradient-based optimization method is used. The results show that the different strength levels observed for micro-bending tests on different crystal orientations can only be described with latent kinematic hardening well, whereas the pronounced Bauschinger effect is described well by both kinematic hardening laws. It is concluded that cyclic micro-bending experiments on single crystals using different crystal orientations give an appropriate data base for the determination of the slip system related material properties of the single crystal plasticity model with latent kinematic hardening.
Cyclic micro-bending tests on fcc single crystal Ni-base Alloy 718 cantilevers with different crystal orientations were performed to analyze the influence of activated slip systems on dislocation plasticity, latent hardening and the Bauschinger effect. The investigations indicate that plasticity in single crystal micro-cantilevers is significantly influenced by two phenomena - dislocation interaction and dislocation pile-up at the neutral plane. Both phenomena occur at the same time. Their ratio seems to be determined by the activated slip systems. Slip trace analysis indicates that the activation of only one slip system leads to a strong localization of plasticity to a limited number of parallel slip bands. This results in low dislocation interaction and consequently pronounced pile-ups at the neutral plane. In multi slip orientation, the second slip system leads to activation of significantly more dislocation sources, causing a much earlier and more homogeneous elastic-plastic transition zone. In stress-strain hysteresis loops during bending, pronounced dislocation interaction in multi slip orientation leads to a more pronounced latent hardening. The results suggest that on a microstructural length scale, plasticity behavior is strongly affected by activated slip systems, which determine local dislocation phenomena. Based on the results presented in this paper, a finite element analysis of latent hardening and the Bauschinger effect using a single crystal plasticity model with latent kinematic hardening is presented in Part II.
Ein tiefgreifendes Verständnis des zyklischen Plastizitätsverhaltens metallischer Werkstoffe ist sowohl für die Optimierung der Materialeigenschaften als auch für die industrielle Auslegung und Fertigung von Bauteilen von hoher Relevanz. Insbesondere moderne Legierungen wie Duplex-Stähle zeigen unter Lastumkehr aufgrund des komplexen mehrphasigen Gefüges sowie der Neigung zu verschiedenen Ausscheidungsreaktionen einen ausgeprägten Bauschinger-Effekt, welcher bei technischen Umformvorgängen berücksichtigt werden muss. Der Bauschinger-Effekt begründet sich maßgeblich in der Entstehung von Rückspannungen, welche aus dem unterschiedlichen Plastizitätsverhalten der austenitischen und ferritischen Phase resultieren. Instrumentierte Mikroindenter-Versuche in ausgewählten Ferrit- und Austenitkörnern haben gezeigt, dass austenitische Gefügebestandteile durch einen deutlich früheren Fließbeginn sowie eine stärkere Rückplastifizierung während der Entlastung charakterisiert sind. Zudem wurde nachgewiesen, dass Ausscheidungen im Rahmen einer 475°C-Versprödung diesen Phasenunterschied verstärken und somit in einem höheren Bauschinger-Effekt resultieren.
A new yield function for lamellar gray cast iron materials is proposed. The new model is able to describe the results of recently performed microstructure-based finite-element computations that resolve the three dimensional yield surface of three different gray cast irons. The yield function requires only the yield stress in tension and compression of the respective material as model parameters. Furthermore, the algorithmic formulation of the new model is assessed for numerical robustness and efficiency.
Cast aluminum alloys are frequently used as materials for cylinder head applications in internal combustion gasoline engines. These components must withstand severe cyclic mechanical and thermal loads throughout their lifetime. Reliable computational methods allow for accurate estimation of stresses, strains, and temperature fields and lead to more realistic Thermomechanical Fatigue (TMF) lifetime predictions. With accurate numerical methods, the components could be optimized via computer simulations and the number of required bench tests could be reduced significantly. These types of alloys are normally optimized for peak hardness from a quenched state that maximizes the strength of the material. However due to high temperature exposure, in service or under test conditions, the material would experience an over-ageing effect that leads to a significant reduction in the strength of the material. To numerically account for ageing effects, the Shercliff & Ashby ageing model is combined with a Chaboche-type viscoplasticity model available in the finite-element program ABAQUS by defining field variables. The constitutive model with ageing effects is correlated with uniaxial cyclic isothermal tests in the T6 state, the overaged state, as well as thermomechanical tests. On the other hand, the mechanism-based TMF damage model (DTMF) is calibrated for both T6 and over-aged state. Both the constitutive and the damage model are applied to a cylinder head component simulating several cycles on an engine dynamometer test. The effects of including ageing for both models are shown.