Open Access

Wireless sensor networks have found their way into a wide range of applications, among which environmental monitoring systems have attracted increasing interests of researchers. Main challenges for these applications are scalability of the network size and energy efficiency of the spatially distributed nodes. Nodes are mostly battery-powered and spend most of their energy budget on the radio transceiver module. In normal operation modes most energy is spent waiting for incoming frames. A so-called Wake-On-Radio (WOR) technology helps to optimize trade-offs between energy consumption, communication range, complexity of the implementation and response time. We already proposed a new protocol called SmartMAC that makes use of such WOR technology. Furthermore, it gives the possibility to balance the energy consumption between sender and receiver nodes depending on the use case. Based on several calculations and simulations, it was predicted that the SmartMAC protocol was significantly more efficient than other schemes being proposed in recent publications, while preserving a certain backward compatibility with standard IEEE802.15.4 transceivers. To verify this prediction, we implemented the SmartMAC protocol for a given hardware platform. This paper compares the realtime performance of the SmartMAC protocol against simulation results, and proves the measured values are very close to the estimated values. Thus we believe that the proposed MAC algorithms outperforms all other Wake-on-Radio MACs.

Due to its potential in improving the efficiency of energy supply, smart energy metering (SEM) has become an area of interest with the surge in Internet of Things (IoT). SEM entails remote monitoring and control of the sensors and actuators associated with the energy supply system. This provides a flexible platform to conceive and implement new data driven Demand Side Management (DSM) mechanisms. The IoT enablement allows the data to be gathered and analyzed at requisite granularity. In addition to efficient use of energy resources and provisioning of power, developing countries face an additional challenge of temporal mismatch in generation capacity and load factors. This leads to widespread deployment of inefficient and expensive Uninterruptible Power Supply (UPS) solutions for limited power provisioning during resulting blackouts. Our proposed “Soft-UPS” allows dynamic matching of load and generation through a combination of managed curtailment. This eliminates inefficiencies in the energy and power value chain and allows a data-driven approach to solving a widespread problem in developing countries, simultaneously reducing both upfront and running costs of conventional UPS and storage. A scalable and modular platform is proposed and implemented in this paper. The architecture employs “WiMODino” using LoRaWAN with a “Lite Gateway” and SQLite repository for data storage. Role based access to the system through an android application has also been demonstrated for monitoring and control.

It is important to minimize the unscheduled downtime of machines caused by outages of machine components in highly automated production lines. Considering machine tools such as, grinding machines, the bearing inside of spindles is one of the most critical components. In the last decade, research has increasingly focused on fault detection of bearings. In addition, the rise of machine learning concepts has also intensified interest in this area. However, up to date, there is no single one-fits-all solution for predictive maintenance of bearings. Most research so far has only looked at individual bearing types at a time. This paper gives an overview of the most important approaches for bearing-fault analysis in grinding machines. There are two main parts of the analysis presented in this paper. The first part presents the classification of bearing faults, which includes the detection of unhealthy conditions, the position of the error (e.g. at the inner or at the outer ring of the bearing) and the severity, which detects the size of the fault. The second part presents the prediction of remaining useful life, which is important for estimating the productive use of a component before a potential failure, optimizing the replacement costs and minimizing downtime.

This paper makes two contributions to the verification of communication protocols by transition systems. Firstly, the paper presents a modeling of a cyclic communication protocol using a synchronized network of transition systems. This protocol enables seamless cryptographic rekeying embedded into cyclic messages. Secondly, we test the protocol using the model checking verification technique.

It seems to be a widespread impression that the use of strong cryptography inevitably imposes a prohibitive burden on industrial communication systems, at least inasmuch as real-time requirements in cyclic fieldbus communications are concerned. AES-GCM is a leading cryptographic algorithm for authenticated encryption, which protects data against disclosure and manipulations. We study the use of both hardware and software-based implementations of AES-GCM. By simulations as well as measurements on an FPGA-based prototype setup we gain and substantiate an important insight: for devices with a 100 Mbps full-duplex link, a single low-footprint AES-GCM hardware engine can deterministically cope with the worst-case computational load, i.e., even if the device maintains a maximum number of cyclic communication relations with individual cryptographic keys. Our results show that hardware support for AES-GCM in industrial fieldbus components may actually be very lightweight.

Das Monitoring von Industrieanlagen stellt in der Wirtschaft sicher, dass hoch-automatisierte Prozesse reibungslos ablaufen können. Meistens steht hier das Monitoring der Anlagen selbst im Mittelpunkt, die Kommunikationsleitungen für den Datenaustausch auf Ethernet-Basis (z.B. Profinet) sind gegenwärtig noch nicht Teil einer kontinuierlichen Überwachung. Zwar werden auch hier die physischen Verbindungen überprüft, jedoch geschieht häufig dies nur zum Zeitpunkt der Inbetriebnahme, wenn die Anlage noch nicht in das Gesamtsystem integriert ist oder während eines Wartungszyklus, wenn die Maschine für die Dauer der Wartung aus dem Betriebsablauf genommen wird. Dies führt dazu, dass insbesondere heute, wo vor allem Ethernet zunehmend als Basis für die industrielle Kommunikation herangezogen wird, Maschinenausfälle aufgrund fehlender Kabelüberwachung immer wahrscheinlicher werden. Um dem entgegenwirken zu können, wurde im Projekt Ko2SiBus ein neues Messverfahren konzipiert, implementiert und validiert, das kostengünstig in neue oder bestehende Systeme integriert werden kann. Um die Tauglichkeit zu zeigen, wurden die Projektergebnisse in Prototypen und Demonstratoren implementiert, die sowohl als Stand-Alone aber auch als Integrationslösungen dienen können.

The Internet of Things (IoT) is expanding to a wide range of fields such as home automation, agriculture, environmental monitoring, industrial applications, and many more. Securing tens of billions of interconnected devices in the near future will be one of the biggest challenges. IoT devices are often constrained in terms of computational performance, area, and power, which demand lightweight security solutions. In this context, hardware-intrinsic security, particularly physically unclonable functions (PUFs), can provide lightweight identification and authentication for such devices. In this paper, random capacitor variations in a switched capacitor PUF circuit are used as a source of entropy to generate unique security keys. Furthermore, a mathematical model based on the ordinary least square method is developed to describe the relationship between random variations in capacitors and the resulting output voltages. The model is used to filter out systematic variations in circuit components to improve the quality of the extracted secrets.

The authors claim that location information of stationary ICT components can never be unclassified. They describe how swarm-mapping crowd sourcing is used by Apple and Google to worldwide harvest geo-location information on wireless access points and mobile telecommunication systems' base stations to build up gigantic databases with very exclusive access rights. After having highlighted the known technical facts, in the speculative part of this article, the authors argue how this may impact cyber deterrence strategies of states and alliances understanding the cyberspace as another domain of geostrategic relevance. The states and alliances spectrum of activities due to the potential existence of such databases may range from geopolitical negotiations by institutions understanding international affairs as their core business, mitigation approaches at a technical level, over means of cyber deterrence-by-retaliation.

Covert- and side-channels as well as techniques to establish them in cloud computing are in focus of research for quite some time. However, not many concrete mitigation methods have been developed and even less have been adapted and concretely implemented by cloud providers. Thus, we recently conceptually proposed C 3 -Sched a CPU scheduling based approach to mitigate L2 cache covert-channels. Instead of flushing the cache on every context switch, we schedule trusted virtual machines to create noise which prevents potential covert-channels. Additionally, our approach aims on preserving performance by utilizing existing instead of artificial workload while reducing covert-channel related cache flushes to cases where not enough noise has been achieved. In this work we evaluate cache covert-channel mitigation and performance impact of our integration of C 3 -Sched in the XEN credit scheduler. Moreover, we compare it to naive solutions and more competitive approaches.

The authentication method of electronic devices, based on individual forms of correlograms of their internal electric noises, is well-known. Specific physical differences in the components – for example, caused by variations in production quality – cause specific electrical signals, i.e. electric noise, in the electronic device. It is possible to obtain this information and to identify the specific differences of the individual devices using an embedded analog-to-digital converter (ADC). These investigations confirm the possibility to identify and authenticate electronic devices using bit templates, calculated from the sequence of values of the normalized autocorrelation function of noise. Experiments have been performed using personal computers. The probability of correct identification and authentication increases with increasing noise recording duration. As a result of these experiments, an accuracy of 98.1% was achieved for a 1 second-long registration of EM for a set of investigated computers.

During the day-to-day exploitation of localization systems in mines, the technical staff tends to incorrectly rearrange radio equipment: positions of devices may not be accurately marked on a map or their positions may not correspond to the truth. This situation may lead to positioning inaccuracies and errors in the operation of the localization system.This paper presents two Bayesian algorithms for the automatic corrections of positions of the equipment on the map using trajectories restored by the inertial measurement units mounted to mobile objects, like pedestrians and vehicles. As a basis, a predefined map of the mine represented as undirected weighted graph was used as input. The algorithms were implemented using the Simultaneous Localization and Mapping (SLAM) approach.The results prove that both methods are capable to detect misplacement of access points and to provide corresponding corrections. The discrete Bayesian filter outperforms the unscented Kalman filter, which, however, requires more computational power.

The number of use cases for autonomous vehicles is increasing day by day especially in commercial applications. One important application of autonomous vehicles can be found within the parcel delivery section. Here, autonomous cars can massively help to reduce delivery efforts and time by supporting the courier actively. One important component of course is the autonomous vehicle itself. Nevertheless, beside the autonomous vehicle, a flexible and secure communication architecture also is a crucial key component impacting the overall performance of such system since it is required to allow continuous interactions between the vehicle and the other components of the system. The communication system must provide a reliable and secure architecture that is still flexible enough to remain practical and to address several use cases. In this paper, a robust communication architecture for such autonomous fleet-based systems is proposed. The architecture provides a reliable communication between different system entities while keeping those communications secure. The architecture uses different technologies such as Bluetooth Low Energy (BLE), cellular networks and Low Power Wide Area Network (LPWAN) to achieve its goals.

Time-Sensitive Networking (TSN) is the most promising time-deterministic wired communication approach for industrial applications. To extend TSN to "IEEE 802.11" wireless networks two challenging problems must be solved: synchronization and scheduling. This paper is focused on the first one. Even though a few solutions already meet the required synchronization accuracies, they are built on expensive hardware that is not suited for mass market products. While next Wi-Fi generation might support the required functionalities, this paper proposes a novel method that makes possible high-precision wireless synchronization using commercial low-cost components. With the proposed solution, a standard deviation of synchronization error of less than 500 ns can be achieved for many use cases and system loads on both CPU and network. This performance is comparable to modern wired real-time field busses, which makes the developed method a significant contribution for the extension of the TSN protocol to the wireless domain.

The evolution of cellular networks from its first generation (1G) to its fourth generation (4G) was driven by the demand of user-centric downlink capacity also technically called Mobile Broad-Band (MBB). With its fifth generation (5G), Machine Type Communication (MTC) has been added into the target use cases and the upcoming generation of cellular networks is expected to support them. However, such support requires improvements in the existing technologies in terms of latency, reliability, energy efficiency, data rate, scalability, and capacity. Originally, MTC was designed for low-bandwidth high-latency applications such as, environmental sensing, smart dustbin, etc. Nowadays there is an additional demand around applications with low-latency requirements. Among other well-known challenges for recent cellular networks such as data rate energy efficiency, reliability etc., latency is also not suitable for mission-critical applications such as real-time control of machines, autonomous driving, tactile Internet etc. Therefore, in the currently deployed cellular networks, there is a necessity to reduce the latency and increase the reliability offered by the networks to support use cases such as, cooperative autonomous driving or factory automation, that are grouped under the denomination Ultra-Reliable Low-Latency Communication (URLLC). This thesis is primarily concerned with the latency into the Universal Terrestrial Radio Access Network (UTRAN) of cellular networks. The overall work is divided into five parts. The first part presents the state of the art for cellular networks. The second part contains a detailed overview of URLLC use cases and the requirements that must be fulfilled by the cellular networks to support them. The work in this thesis is done as part of a collaboration project between IRIMAS lab in Université de Haute-Alsace, France and Institute for Reliable Embedded Systems and Communication Electronics (ivESK) in Offenburg University of Applied Sciences, Germany. The selected use cases of URLLC are part of the research interests of both partner institutes. The third part presents a detailed study and evaluation of user- and control-plane latency mechanisms in current generation of cellular networks. The evaluation and analysis of these latencies, performed with the open-source ns-3 simulator, were conducted by exploring a broad range of parameters that include among others, traffic models, channel access parameters, realistic propagation models, and a broad set of cellular network protocol stack parameters. These simulations were performed with low-power, low-cost, and wide-range devices, commonly called IoT devices, and standardized for cellular networks. These devices use either LTE-M or Narrowband-IoT (NB-IoT) technologies that are designed for connected things. They differ mainly by the provided bandwidth and other additional characteristics such as coding scheme, device complexity, and so on. The fourth part of this thesis shows a study, an implementation, and an evaluation of latency reduction techniques that target the different layers of the currently used Long Term Evolution (LTE) network protocol stack. These techniques based on Transmission Time Interval (TTI) reduction and Semi-Persistent Scheduling (SPS) methods are implemented into the ns-3 simulator and are evaluated through realistic simulations performed for a variety of low-latency use cases focused on industry automation and vehicular networking. For testing the proposed latency reduction techniques in cellular networks, since ns-3 does not support NB-IoT in its current release, an NB-IoT extension for LTE module was developed. This makes it possible to explore deployment limitations and issues. In the last part of this thesis, a flexible deployment framework called Hybrid Scheduling and Flexible TTI for the proposed latency reduction techniques is presented, implemented and evaluated through realistic simulations. With help of the simulation evaluation, it is shown that the improved LTE network proposed and implemented in the simulator can support low-latency applications with low cost, higher range, and narrow bandwidth devices. The work in this thesis points out the potential improvement techniques, their deployment issues and paves the way towards the support for URLLC applications with upcoming cellular networks.

The status quo of PROFINET, a commonly used industrial Ethernet standard, provides no inherent security in its communication protocols. In this thesis an approach for protecting real-time PROFINET RTC messages against spoofing, tampering and optionally information disclosure is specified and implemented into a real-world prototype setup. Therefor authenticated encryption is used, which relies on symmetric cipher schemes. In addition a procedure to update the used symmetric encryption key in a bumpless manner, e.g. without interrupting the real-time communication, is introduced and realized. The concept for protecting the PROFINET RTC messages was developed in collaboration with a task group within the security working group of PROFINET International. The author of this thesis has also been part of that task group. This thesis contributes by proofing the practicability of the concept in a real-world prototype setup, which consists of three FPGA-based development boards that communicate with each other to showcase bumpless key updates. To enable a bumpless key update without disturbing the deterministic real-time traffic by dedicated messages, the key update annunciation and status is embedded into the header. By provisioning two key slots, of which only one is in used, while the other is being prepared, a well-synchronized coordinated switch between the receiver and the sender performs the key update. The developed prototype setup allows to test the concept and builds the foundation for further research and implementation activities, e.g. the impact of cryptographic operations onto the processing time.

This work discusses several use cases of post-mortem mobile device tracking in which privacy is required e.g. due to client-confidentiality agreements and sensibility of data from government agencies as well as mobile telecommunication providers. We argue that our proposed Bloomfilter based privacy approach is a valuable technical building block for the arising General Data Protection Regulation (GDPR) requirements in this area. In short, we apply a solution based on the Bloom filters data structure that allows a 3rd party to performsome privacy saving setrelations on a mobiletelco’s access logfile or other mobile access logfile from harvesting parties without revealing any other mobile users in the proximity of a mobile base station but still allowing to track perpetrators.

The monitoring of industrial environments ensures that highly automated processes run without interruption. However, even if the industrial machines themselves are monitored, the communication lines are currently not continuously monitored in todays installations. They are checked usually only during maintenance intervals or in case of error. In addition, the cables or connected machines usually have to be removed from the system for the duration of the test. To overcome these drawbacks, we have developed and implemented a cost-efficient and continuous signal monitoring of Ethernet-based industrial bus systems. Several methods have been developed to assess the quality of the cable. These methods can be classified to either passive or active. Active methods are not suitable if interruption of the communication is undesired. Passive methods, on the other hand, require oversampling, which calls for expensive hardware. In this paper, a novel passive method combined with undersampling targeting cost-efficient hardware is proposed.

When designing and installing Indoor Positioning Systems, several interrelated tasks have to be solved to find an optimum placement of the Access Points. For this purpose, a mathematical model for a predefined number of access points indoors is presented. Two iterative algorithms for the minimization of localization error of a mobile object are described. Both algorithms use local search technique and signal level probabilities. Previously registered signal strengths maps were used in computer simulation.

The Internet of Things (IoT) application has becoming progressively in-demand, most notably for the embedded devices (ED). However, each device has its own difference in computational capabilities, memory usage, and energy resources in connecting to the Internet by using Wireless Sensor Networks (WSNs). In order for this to be achievable, the WSNs that form the bulk of the IoT implementation requires a new set of technologies and protocol that would have a defined area, in which it addresses. Thus, IPv6 Low Power Area Network (6LoWPAN) was designed by the Internet Engineering Task Force (IETF) as a standard network for ED. Nevertheless, the communication between ED and 6LoWPAN requires appropriate routing protocols for it to achieve the efficient Quality of Service (QoS). Among the protocols of 6LoWPAN network, RPL is considered to be the best protocol, however its Energy Consumption (EC) and Routing Overhead (RO) is considerably high when it is implemented in a large network. Therefore, this paper would propose the HRPL to enchance the RPL protocol in reducing the EC and RO. In this study, the researchers would present the performance of RPL and HRPL in terms of EC, Control traffic Overhead (CTO) and latency based on the simulation of the 6LoWPAN network in fixed environment using COOJA simulator. The results show HRPL protocol achieves better performance in all the tested topology in terms of EC and CTO. However, the latency of HRPL only improves in chain topology compared with RPL. We found that further research is required to study the relationship between the latency and the load of packet transmission in order to optimize the EC usage.

Uncontrollable manufacturing variations in electrical hardware circuits can be exploited as Physical Unclonable Functions (PUFs). Herein, we present a Printed Electronics (PE)-based PUF system architecture. Our proposed Differential Circuit PUF (DiffC-PUF) is a hybrid system, combining silicon-based and PE-based electronic circuits. The novel approach of the DiffC-PUF architecture is to provide a specially designed real hardware system architecture, that enables the automatic readout of interchangeable printed DiffC-PUF core circuits. The silicon-based addressing and evaluation circuit supplies and controls the printed PUF core and ensures seamless integration into silicon-based smart systems. Major objectives of our work are interconnected applications for the Internet of Things (IoT).

The next generation cellular networks are expected to improve reliability, energy efficiency, data rate, capacity and latency. Originally, Machine Type Communication (MTC) was designed for low-bandwidth high-latency applications such as, environmental sensing, smart dustbin, etc., but there is additional demand around applications with low latency requirements, like industrial automation, driver-less cars, and so on. Improvements are required in 4G Long Term Evolution (LTE) networks towards the development of next generation cellular networks for providing very low latency and high reliability. To this end, we present an in-depth analysis of parameters that contribute to the latency in 4G networks along with a description of latency reduction techniques. We implement and validate these latency reduction techniques in the open-source network simulator (NS3) for narrowband user equipment category Cat-Ml (LTE-M) to analyze the improvements. The results presented are a step towards enabling narrowband Ultra Reliable Low Latency Communication (URLLC) networks.

The Datagram Transport Layer Security (DTLS) protocol has been designed to provide end-to-end security over unreliable communication links. Where its connection establishment is concerned, DTLS copes with potential loss of protocol messages by implementing its own loss detection and retransmission scheme. However, the default scheme turns out to be suboptimal for links with high transmission error rates and low data rates, such as wireless links in electromagnetically harsh industrial environments. Therefore, in this paper, as a first step we provide an analysis of the standard DTLS handshake's performance under such adverse transmission conditions. Our studies are based on simulations that model message loss as the result of bit transmission errors. We consider several handshake variants, including endpoint authentication via pre-shared keys or certificates. As a second step, we propose and evaluate modifications to the way message loss is dealt with during the handshake, making DTLS deployable in situations which are prohibitive for default DTLS.

Recently, the demand for scalable, efficient and accurate Indoor Positioning Systems (IPS) has seen a rising trend due to their utility in providing Location Based Services (LBS). Visible Light Communication (VLC) based IPS designs, VLC-IPS, leverage Light Emitting Diodes (LEDs) in indoor environments for localization. Among VLC-based designs, Time Difference of Arrival (TDOA) based techniques are shown to provide very low errors in the relative position of receivers. Our considered system consists of five LEDs that act as transmitters and a single receiver (photodiode or image sensor in smart phone) whose position coordinates in an indoor environment are to be determined. As a performance criterion, Cramer Rao Lower Bound (CRLB) is derived for range estimations and the impact of various factors, such as, LED transmission frequency, position of reference LED light, and the number of LED lights, on localization accuracy has been studied. Simulation results show that depending on the optimal values of these factors, location estimation on the order of few centimeters can be realistically achieved.