Open Access

With the surge in global data consumption with proliferation of Internet of Things (IoT), remote monitoring and control is increasingly becoming popular with a wide range of applications from emergency response in remote regions to monitoring of environmental parameters. Mesh networks are being employed to alleviate a number of issues associated with single-hop communication such as low area coverage, reliability, range and high energy consumption. Low-power Wireless Personal Area Networks (LoWPANs) are being used to help realize and permeate the applicability of IoT. In this paper, we present the design and test of IEEE 802.15.4-compliant smart IoT nodes with multi-hop routing. We first discuss the features of the software stack and design choices in hardware that resulted in high RF output power and then present field test results of different baseline network topologies in both rural and urban settings to demonstrate the deployability and scalability of our solution.

The monitoring of industrial environments ensures that highly automated processes run without interruption. However, even if the industrial machines themselves are monitored, the communication lines are currently not continuously monitored in todays installations. They are checked usually only during maintenance intervals or in case of error. In addition, the cables or connected machines usually have to be removed from the system for the duration of the test. To overcome these drawbacks, we have developed and implemented a cost-efficient and continuous signal monitoring of Ethernet-based industrial bus systems. Several methods have been developed to assess the quality of the cable. These methods can be classified to either passive or active. Active methods are not suitable if interruption of the communication is undesired. Passive methods, on the other hand, require oversampling, which calls for expensive hardware. In this paper, a novel passive method combined with undersampling targeting cost-efficient hardware is proposed.

This article deals with the problem of wireless synchronization between onboard computing devices of small-sized unmanned aerial vehicles (SUAV) equipped with integrated wireless chips (IWC). Accurate synchronization between several devices requires the precise timestamping of batches transmitting and receiving on each of them. The best precision is demonstrated by those solutions where timestamping is performed on the PHY level, right after modulation/demodulation of the batch. Nowadays, most of the currently produced IWC are Systems-on-a-Chip (SoC) that include both PHY and MAC, implemented with one or several processor cores application. SoC allows create more cost and energy efficient wireless devices. At the same time, it limits the developers direct access to the internal signals and significantly complicates precise timestamping for sent and received batches, required for mutual synchronization of industrial devices. Some modern IEEE 802.11 IWCs have inbuilt functions that use internal chip clock to register timestamps. However, high jitter of the interfaces between the external device and IWC degrades the comparison of the timestamps from the internal clock to those registered by external devices. To solve this problem, the article proposes a novel approach to the synchronization, based on the analysis of IWC receiver input potential. The benefit of this approach is that there is no need to demodulate and decode the received batches, thus allowing it implementation with low-cost IWCs. In this araticle, Cypress CYW43438 was taken as an example for designing hardware and software solutions for synchronization between two SUAV onboard computing devices, equipped with IWC. The results of the performed experimental studies reveal that mutual synchronization error of the proposed method does not exceed 10 μs.

Time-Sensitive Networking (TSN) is the most promising time-deterministic wired communication approach for industrial applications. To extend TSN to "IEEE 802.11" wireless networks two challenging problems must be solved: synchronization and scheduling. This paper is focused on the first one. Even though a few solutions already meet the required synchronization accuracies, they are built on expensive hardware that is not suited for mass market products. While next Wi-Fi generation might support the required functionalities, this paper proposes a novel method that makes possible high-precision wireless synchronization using commercial low-cost components. With the proposed solution, a standard deviation of synchronization error of less than 500 ns can be achieved for many use cases and system loads on both CPU and network. This performance is comparable to modern wired real-time field busses, which makes the developed method a significant contribution for the extension of the TSN protocol to the wireless domain.

Modern society is striving for digital connectivity that demands information security. As an emerging technology, printed electronics is a key enabler for novel device types with free form factors, customizability, and the potential for large-area fabrication while being seamlessly integrated into our everyday environment. At present, information security is mainly based on software algorithms that use pseudo random numbers. In this regard, hardware-intrinsic security primitives, such as physical unclonable functions, are very promising to provide inherent security features comparable to biometrical data. Device-specific, random intrinsic variations are exploited to generate unique secure identifiers. Here, we introduce a hybrid physical unclonable function, combining silicon and printed electronics technologies, based on metal oxide thin film devices. Our system exploits the inherent randomness of printed materials due to surface roughness, film morphology and the resulting electrical characteristics. The security primitive provides high intrinsic variation, is non-volatile, scalable and exhibits nearly ideal uniqueness.

The authentication method of electronic devices, based on individual forms of correlograms of their internal electric noises, is well-known. Specific physical differences in the components – for example, caused by variations in production quality – cause specific electrical signals, i.e. electric noise, in the electronic device. It is possible to obtain this information and to identify the specific differences of the individual devices using an embedded analog-to-digital converter (ADC). These investigations confirm the possibility to identify and authenticate electronic devices using bit templates, calculated from the sequence of values of the normalized autocorrelation function of noise. Experiments have been performed using personal computers. The probability of correct identification and authentication increases with increasing noise recording duration. As a result of these experiments, an accuracy of 98.1% was achieved for a 1 second-long registration of EM for a set of investigated computers.

Maintenance processes in Industry 4.0 applications try to achieve a high degree of quality to reduce the downtime of machinery. The monitoring of executed maintenance activities is challenging as in complex production setups, multiple stakeholders are involved. So, full transparency of the different activities and of the state of the machine can only be supported, if these stakeholders trust each other. Therefore, distributed ledger technologies, like Blockchain, can be promising candidates for supporting such applications. The goal of this paper is a formal description of business and technical interactions between non-trustful stakeholders in the context of Industry 4.0 maintenance processes using distributed ledger technologies. It also covers the integration of smart contracts for automated triggering of activities.

The Internet of Things (IoT) application has becoming progressively in-demand, most notably for the embedded devices (ED). However, each device has its own difference in computational capabilities, memory usage, and energy resources in connecting to the Internet by using Wireless Sensor Networks (WSNs). In order for this to be achievable, the WSNs that form the bulk of the IoT implementation requires a new set of technologies and protocol that would have a defined area, in which it addresses. Thus, IPv6 Low Power Area Network (6LoWPAN) was designed by the Internet Engineering Task Force (IETF) as a standard network for ED. Nevertheless, the communication between ED and 6LoWPAN requires appropriate routing protocols for it to achieve the efficient Quality of Service (QoS). Among the protocols of 6LoWPAN network, RPL is considered to be the best protocol, however its Energy Consumption (EC) and Routing Overhead (RO) is considerably high when it is implemented in a large network. Therefore, this paper would propose the HRPL to enchance the RPL protocol in reducing the EC and RO. In this study, the researchers would present the performance of RPL and HRPL in terms of EC, Control traffic Overhead (CTO) and latency based on the simulation of the 6LoWPAN network in fixed environment using COOJA simulator. The results show HRPL protocol achieves better performance in all the tested topology in terms of EC and CTO. However, the latency of HRPL only improves in chain topology compared with RPL. We found that further research is required to study the relationship between the latency and the load of packet transmission in order to optimize the EC usage.

A physical unclonable function (PUF) is a hardware circuit that produces a random sequence based on its manufacturing-induced intrinsic characteristics. In the past decade, silicon-based PUFs have been extensively studied as a security primitive for identification and authentication. The emerging field of printed electronics (PE) enables novel application fields in the scope of the Internet of Things (IoT) and smart sensors. In this paper, we design and evaluate a printed differential circuit PUF (DiffC-PUF). The simulation data are verified by Monte Carlo analysis. Our design is highly scalable while consisting of a low number of printed transistors. Furthermore, we investigate the best operating point by varying the PUF challenge configuration and analyzing the PUF security metrics in order to achieve high robustness. At the best operating point, the results show areliability of 98.37% and a uniqueness of 50.02%, respectively. This analysis also provides useful and comprehensive insights into the design of hybrid or fully printed PUF circuits. In addition, the proposed printed DiffC-PUF core has been fabricated with electrolyte-gated field-effect transistor technology to verify our design in hardware.

Ultra-Reliable Low Latency Communications (URLLC) has been always a vital component of many industrial applications. The paper proposes a new wireless URLLC solution called RETIS, which is suitable for factory automation and fast process control applications, where low latency, low jitter, and high data exchange rates are mandatory. In the paper, we describe the communication protocol as well as the hardware structure of the network nodes for implementing the required functionality. Many techniques enabling fast, reliable wireless transmissions are used – short Transmission Time Interval (TTI), Time-Division Multiple Access (TDMA), MIMO, optional duplicated data transfer, Forward Error Correction (FEC), ACK mechanism. Preliminary tests show that reliable end-to-end latency down to 350 μs and packet exchange rate up to 4 kHz can be reached (using quadruple MIMO and standard IEEE 802.15.4 PHY at 250 kbit/s).