Refine
Document Type
- Article (reviewed) (3)
- Doctoral Thesis (1)
Language
- English (4)
Is part of the Bibliography
- yes (4)
Keywords
- Modeling (4) (remove)
Institute
Open Access
- Open Access (3)
- Closed Access (1)
- Diamond (1)
Electrochemical pressure impedance spectroscopy (EPIS) has received the attention of researchers as a method to study mass transport processes in polymer electrolyte mem-brane fuel cells (PEMFC). It is based on analyzing the cell voltage response to a harmonic excitation of the gas phase pressure in the frequency domain. Several experiments with a single-cell fuel cell have shown that the spectra contain information in the frequency range typical for mass transport processes and are sensitive to specific operating condi-tions and structural fuel cell parameters. To further benefit from the observed features, it is essential to identify why they occur, which to date has not yet been accomplished. The aim of the present work, therefore, is to identify causal links between internal processes and the corresponding EPIS features.
To this end, the study follows a model-based approach, which allows the analysis of inter-nal states that are not experimentally accessible. The PEMFC model is a pseudo-2D model, which connects the mass transport along the gas channel with the mass transport through the membrane electrode assembly. A modeling novelty is the consideration of the gas vol-ume inside the humidifier upstream the fuel cell inlet, which proves to be crucial for the reproduction of EPIS. The PEMFC model is parametrized to a 100 cm² single cell of the French project partner, who provided the experimental EPIS results reproduced and in-terpreted in the present study.
The simulated EPIS results show a good agreement with the experiments at current den-sities ≤ 0.4 A cm–2, where they allow a further analysis of the observed features. At the lowest excitation frequency of 1 mHz, the dynamic cell voltage response approaches the static pressure-voltage response. In the simulated frequency range between 1 mHz – 100 Hz, the cell voltage oscillation is found to strongly correlate with the partial pressure oscillation of oxygen, whereas the influence of the water pressure is limited to the low frequency region.
The two prominent EPIS features, namely the strong increase of the cell voltage oscillation and the increase of phase shift with frequency, can be traced back via the oxygen pressure to the oscillation of the inlet flow rate. The phenomenon of the oscillating inlet flow rate is a consequence of the pressure change of the gas phase inside the humidifier and in-creases with frequency. This important finding enables the interpretation of experimen-tally observed EPIS trends for a variation of operational and structural fuel cell parame-ters by tracing them back to the influence of the oscillating inlet flow rate.
The separate simulation of the time-dependent processes of the PEMFC model through model reduction shows their individual influence on EPIS. The sluggish process of the wa-ter uptake by the membrane is visible below 0.1 Hz, while the charge and discharge of the double layer becomes visible above 1 Hz. The gas transport through the gas diffusion layer is only visible above 100 Hz. The simulation of the gas transport through the gas channel
without consideration of the humidifier becomes visible above 1 Hz. With consideration of the humidifier the gas transport through the gas channel is visible throughout the fre-quency range. The strong similarity of the spectra considering the humidifier with the spectra of the full model setup shows the dominant influence of the humidifier on EPIS.
A promising observation is the change in the amplitude relationship between the cell volt-age and the oxygen partial pressure oscillation as a function of the oxygen concentration in the catalyst layer. At a frequency where the influence of oxygen pressure on the cell voltage is dominant, for example at 1 Hz, the amplitude of the cell voltage oscillation could be used to indirectly measure the oxygen concentration in the catalyst layer.
Oxidation of the nickel electrode is a severe aging mechanism of solid oxide fuel cells (SOFC) and solid oxide electrolyzer cells (SOEC). This work presents a modeling study of safe operating conditions with respect to nickel oxide formation. Microkinetic reaction mechanisms for thermochemical and electrochemical nickel oxidation are integrated into a 2D multiphase model of an anode‐supported solid oxide cell. Local oxidation propensity can be separated into four regimes. Simulations show that the thermochemical pathway generally dominates the electrochemical pathway. As a consequence, as long as fuel utilization is low, cell operation considerably below electrochemical oxidation limit of 0.704 V is possible without the risk of reoxidation.
We present an electrochemical model of a lithium iron phosphate/graphite (LFP/C6) cell that includes combined aging mechanisms: (i) Electrochemical formation of the solid electrolyte interphase (SEI) at the anode, leading to loss of lithium inventory, (ii) breaking of the SEI due to volume changes of the graphite particles, causing accelerated SEI growth, and (iii) loss of active material due to of loss percolation of the liquid electrolyte resulting from electrode dry-out. The latter requires the introduction of an activity-saturation relationship. A time-upscaling methodology is developed that allows to simulate large time spans (thousands of operating hours). The combined modeling and simulation framework is able to predict calendaric and cyclic aging up to the end of life of the battery cells. The aging parameters are adjusted to match literature calendaric and cyclic aging experiments, resulting in quantitative agreement of simulated nonlinear capacity loss with experimental data. The model predicts and provides an interpretation for the dependence of capacity loss on temperature, cycling depth, and average SOC. The introduction of a percolation threshold in the activity-saturation relationship allows to capture the strong nonlinearity of aging toward end of life (“sudden death”).
One of the practical bottlenecks associated with commercialization of lithium-air cells is the choice of an appropriate electrolyte that provides the required combination of cell performance, cyclability and safety. With the help of a two-dimensional multiphysics model, we attempt to narrow down the electrolyte choice by providing insights into the effect of the transport properties of electrolyte, electrode saturation (flooded versus gas diffusion), and electrode thickness on a single discharge performance of a lithium-air button cell cathode for five different electrolytes including water, ionic liquid, carbonate, ether, and sulfoxide. The 2D distribution of local current density and concentrations of electrochemically active species (O2 and Li+) in the cathode is also discussed w.r.t electrode saturation. Furthermore, the efficacy of species transport in the cathode is quantified by introducing two parameters, firstly, a transport efficiency that gives local insight into the distribution of mass transfer losses, and secondly, an active electrode volume that gives global insight into the cathode volume utilization at different current densities. A detailed discussion is presented toward understanding the design-induced performance limitations in a Li-air button cell prototype.