Refine
Year of publication
- 2013 (20) (remove)
Document Type
- Conference Proceeding (13)
- Article (unreviewed) (5)
- Article (reviewed) (1)
- Part of a Book (1)
Conference Type
- Konferenzartikel (13)
Is part of the Bibliography
- yes (20)
Keywords
- Kommunikation (5)
- Sicherheit (3)
- Drahtloses lokales Netz (2)
- Energieversorgung (2)
- Messung (2)
- Sicherheitstechnik (2)
- Android (1)
- Automation (1)
- Automatisierungssystem (1)
- Bussystem (1)
Open Access
- Closed Access (11)
- Open Access (5)
- Bronze (1)
A highly scalable IEEE802.11p communication and localization subsystem for autonomous urban driving
(2013)
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed for the support of highly autonomous driving. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. Thus it is mainly targeted for the support of traffic safety applications in intra-urban scenarios. This contribution describes the Ko-TAG part of the overall initiative, which develops a subsystem to improve the real-time characteristics of IEEE802.11p needed for precise time of flight real-time localization. In doing this, it still fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. Test results are shown in the last part of the paper.
A Localization System Using Inertial Measurement Units from Wireless Commercial Handheld Devices
(2013)
This paper describes a newly developed technology for the calculation of trajectories of mobile objects, which is based on commercially available sensors being integrated into modern mobile phones and other gadgets. First, a step counting technique was implemented. Second, a novel step length estimator is proposed. These two algorithms utilize the data from accelerometer sensor only. Third, the heading information was obtained using a gyroscope with complementary filter in quaternion form. The combined algorithm was implemented on a low-power ARM processor to provide the trajectory points relative to an initial point. The proposed technique was tested by 10 subjects, in different shoes with different paces. The dependence of the performance of the technology on the attaching point of the mobile device is weak. The proposed algorithms have better balance and estimation accuracy and depend in less degree on the variety in physical parameters of people in comparison with the existing techniques. In experiments inertial measurement units were mounted in different places, i.e. in the hand, in trousers or in T-shirt pockets. The return position error did not exceed 5% of the total travelled distance for all performed tests.
The communication technologies for automatic meter reading (smart metering) and for energy production and distribution networks (smart grid) have the potential to be one of the first really highly scaled machine-to-machine-M2M-applications. During the last years, two very promising developments around the wireless part of the smart grid communication were initialized, which possibly could have an impact on the network architectures and the markets far beyond Germany and far beyond energy automation. Besides the specification of the OMS Group of a security extension to the Wireless M-Bus protocol (EN13757-4), the German Federal Office for Information Security (Bundesamt für Sicherheit in der Informationstechnik, BSI) has designed a Protection Profile (PP) and a Technical Directive (TR) for the communication unit of an intelligent measurement system (Smart Meter Gateway), which were released in March 2013. This design uses state of the art technologies and prescribes their implementation in real-life systems. At first, the proposed paper will present the most important characteristics of this architecture. It will then give an insight into the implementation of the OMS security protocols, which imply the usage of a mutually authenticated SSL protocol also in the Local Metrological Network. This is achieved with the help of an additional Authentication and Fragmentation Layer (AFL). This secure communication will be terminated in a BSI conformant secure smart meter gateway, which is developed in a different project and described in the second step. Finally, the contribution will discuss the integration of such a metering network into an overall telecommunication network and PKI infrastructure.
Efficient, low-cost, secure and reliable communication solutions are a major stepping stone for smart metering and smart grid applications. This especially holds true for the so called primary communication or local metrological network (LMN) between a local meter or actuator and a data collector or gateway, where the highest requirements with regard to cost, bandwidth, and energy efficiency have to be taken into consideration. Multiple developments and field tests are going on in this field, however, energy autarkic devices are hardly found, yet. This contribution describes the development of an automatic water meter reading (AWMR) technology based on Wireless M-Bus to provide water utility companies with an automatic remote water meter reading solution. It addresses the special needs of home utilities by providing a remote metering solution independent from the electricity infrastructure, both in terms of data communication and in terms of power supply. For this project, a cost efficient integrated energy harvesting system powered by the available water flow was developed, to enable operation independently of the mains grid, and eliminate the need for battery replacement for near-zero maintenance costs.
The communication technologies for automatic me-ter reading (smart metering) and for energy production and distribution networks (smart grid) have the potential to be one of the first really highly scaled machine-to-machine-(M2M)-applications. During the last years two very promising devel-opments around the wireless part of smart grid communication were initialized, which possibly have an impact on the markets far beyond Europe and far beyond energy automation. Besides the specifications of the Open Metering System (OMS) Group, the German Federal Office for Information Security (Bundesamt für Sicherheit in der Informationstechnik, BSI) has designed a protection profile (PP) and a technical directive (TR) for the communication unit of an intelligent measurement sys-tem (smart meter gateway), which were released in March 2013. This design uses state-of-the-art technologies and prescribes their implementation in real-life systems. At first sight the expenditures for the prescribed solutions seem to be significant. But in the long run, this path is inevitable and comes with strategic advantages.
Efficient, low-cost, secure and reliable communication solutions are a major stepping stone for smart metering and smart grid applications. This especially holds true for the so called primary communication or local metrological network (LMN) between a local meter or actuator and a data collector or gateway, where the highest requirements with regard to cost, bandwidth, and energy efficiency have to be taken into consideration. Multiple developments and field tests are going on in this field, however, energy autarkic devices are hardly found, yet.
Ranging errors are inevitable in all local positioning systems, including those based on Time-of-Flight (ToF) technique. Results of experiments show that the major cause for these errors is a signal degradation from multipath propagation. This effect is especially critical in case of Non-Light-of-Sight (NLOS) conditions. This paper describes causes that affects ranging errors for nanoLOC™-TOF-technology and presents estimations for the probability density functions of such errors under different NLOS conditions. The provided estimations allow the improvement of the accuracy of the localization through the subsequent mitigation of the ranging errors from the measurements. Additionally, it is proposed to increase the number of cases of NLOS-conditions for the improvement of the accuracy.
Automatic Meter Reading (AMR) is a major enabler for the upcoming smart grid. Potentially, it will be one of the first really large-scale M2M-communication solutions for sensor applications.
To date, the definition of the standardized communication stacks for Local Metrological Network (LMN) in AMR is still ongoing. This holds true both for ZigBee Smart Energy Profile and for Wireless M-Bus according to EN 13757. During this process, there is the necessity for flexible, albeit optimized solutions, which support the different existing and upcoming versions of the communication protocols. In the case of Wireless M-Bus, the major contender for European and possibly Asian installations, this is valid not only for the different operation modes (C-, N-, P-, Q-, R-, S-, and T-modes), which work in different frequencies (i.e. 868 MHz, 433 MHz, and 169 MHz) but also for the application layer, where additional bodies, like EN137575, Open Metering System (OMS) Group, or national bodies follow their approaches.
This contribution describes requirements, design techniques and experiences from the development of highly efficient Wireless M-Bus protocol stacks with support of good flexibility and portability between microcontroller platforms and RF-transceivers. The presented approach is not limited to the use of modern software engineering design processes, as such, but also includes essential additional features like testing or simulation, as well as tools for commissioning and monitoring.
Die Energiewende ist ein elementares Thema, für Deutschland wie auch für viele andere Regionen weltweit. Bei der Bereitstellung effizienter und stabiler Verteilnetze stellen Kommunikationslösungen einen zentralen Baustein dar, um auf der Grundlage eines zeitnahen Monitorings koordinierte Regelalgorithmen zu realisieren. Dies gilt für alle Ebenen der Versorgung, wobei aus Sicht der Kommunikationstechnik die unterste Ebene der Verteilnetze am interessantesten ist: Hier sind die anspruchsvollsten Anforderungen im Hinblick auf die Kosten- und die Energieoptimierung der Kommunikationsknoten sowie die Administrierbarkeit, die Stabilität und die Skalierbarkeit der Gesamtlösung zu berücksichtigen. Das Steinbeis-Transferzentrum Embedded Design und Networking an der Hochschule Offenburg unter der Leitung von Prof. Dr.-Ing. Axel Sikora hat in verschiedenen Projekten mit renommierten Partnern umfangreiche Lösungen für diese sogenannte Primärkommunikation entwickelt.
Android is an operating system which was developed for use in smart mobile phones and is the current leader in this market. A lot of efforts are being spent to make Android available to the embedded world, as well. Many embedded systems do not have a local GUI and are therefore called headless devices. This paper presents the results of an analysis of the general suitability of Anroid in headless embedded systems and ponders the advantages and disadvantages. It focuses on the hardware related issues, i.e. to what extent Android supports hardware peripherals normally used in embedded systems.
The communication between objects, i.e. between cars (car-2-car, C2C), between cars and infrastructure (car-2-infrastructure, C2I) and between cars and vulnerable road users (car-2-VRU, C2VRU) is a major stepping stone towards traffic applications to enable efficient and safe traffic flow. However, these applications pose very high requirements to the communication protocols, which go beyond the capabilities of an available standardized solution.
This contribution shows how iterative design processes can help to fulfill these requirements, while re-using a maximum of elements from one level to the next and thus avoiding unrealistic overhead. In especially, the added value of simulation and emulation in this iterative process is elaborated.
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed and its benefit for traffic safety applications is evaluated. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. The Ko-TAG proposal enriches the current IEEE802.11p real-time characteristics needed for precise time-of-flight real-time localization. This contribution describes the development of a subsystem, which extends the functionality of IEEE802.11p and fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. The next step will be field measurements to verify the simulation results.
Die Kommunikationstechnik für die Zählerfernauslesung (Smart Metering) und für die Energieerzeugungs- und -verteilnetze (Smart Grid) hat das Potenzial, zu einer der ersten hoch skalierten M2M-Anwendungen zu werden. In den vergangenen Jahren konnten zwei vielversprechende Entwicklungen im Umfeld der drahtlosen Kommunikation für die Smart-Grid-Kommunikation vorbereitet werden, die das Marktgeschehen über Deutschland und über die Versorgungstechnik hinaus beeinflussen könnten. Neben der Spezifikation der OMS-Gruppe ist die Erarbeitung eines Schutzprofils (Protection Profile, PP) sowie einer Technischen Richtlinie (TR) für die Kommunikationseinheit eines intelligenten Messsystems (Smart Meter Gateway) durch das Bundesamt für Sicherheit in der Informationstechnik (BSI) zu nennen. Diese greifen, wie der Beitrag beschreibt, den Stand der Technik auf und geben praxisorientierte Umsetzungen vor.