Refine
Year of publication
Document Type
- Conference Proceeding (18)
- Part of a Book (12)
- Contribution to a Periodical (8)
- Book (7)
- Article (reviewed) (4)
- Article (unreviewed) (4)
Conference Type
- Konferenzartikel (10)
- Konferenz-Abstract (4)
- Konferenz-Poster (4)
- Sonstiges (2)
Is part of the Bibliography
- yes (53)
Keywords
- Emission (3)
- Hybridantrieb (3)
- Partikel (3)
- Blockheiz-Kraftwerk (2)
- Energiequelle (2)
- Energietechnik (2)
- FFF (2)
- Verbrennungsmotor (2)
- Aerosol (1)
- Arbeitsmaschine (1)
Institute
Open Access
- Closed Access (15)
- Open Access (15)
- Closed (13)
- Bronze (3)
Mit gleichem kommunalem Mehrzweck-Fahrzeug (Abb. 1) wurden mehrere Fahrzyklen mit konventionellem Dieselantrieb und mit parallelem diesel-elektrischem Hybridantrieb simuliert. Aus den Ergebnissen der realen Fahrzyklen mit konventionellem Dieselmotorantrieb ließen sich die Kraftstoffeinsparpotenziale mit dem Hybridmotor und den verschiedenen Maßnahmen wie Start-Stopp, Rekuperation und Boost ermitteln. Selbst bei diesem Kommunalfahrzeug lassen sich Kraftstoffeinsparungen bis über 20 % nachweisen, obwohl die Fahrzyklen für Hybridanwendungen nicht besonders attraktiv sind. Deutlich höhere Potenziale liegen beispielsweise bei Gabelstaplern und Baumaschinen vor.
Specific prototypes of sedimentation field flow fractionation devices (SdFFF) have been developed with relative success for cell sorting. However, no data are available to compare these apparatus with commercial ones. In order to compare with other devices mainly used for non-biological species, biocompatible systems were used for standard particle (latex: 3–10 μm of different size dispersities) separation development. In order to enhance size dependent separations, channels of reduced thickness were used (80 and 100 μm) and channel/carrier-phase equilibration procedures were necessary. For sample injection, the use of inlet tubing linked to the FFF accumulation wall, common for cell sorting, can be extended to latex species when they are eluted in the Steric Hyperlayer elution mode. It avoids any primary relaxation steps (stop flow injection procedure) simplifying series of elution processing. Mixtures composed of four different monodispersed latex beads can be eluted in 6 min with 100 μm channel thickness.
Non-Esterified Plant Oils as Fuel -Engine Characteristics, Emissions and Mutagenic effects of PM-
(2009)
Plant oils may be used as a sustainable, nearly CO2 neutral fuel for diesel engines. This work investigates experimentally the particulate and gaseous emissions of diesel engines fuelled with non-esterified, pure plant oils with the quality standard of DIN V 51605 (Weihen-stephan RK-Qualitätsstandard 05/2000). The data are collected from three engines:
Common rail passenger car engine from OPEL AG
Truck engine from VOLVO
Truck engine from MAN AG
All engines have been correctly adjusted to plant oil operation.
The OPEL and VOLVO engines served for the basic investigations. The emissions of the MAN engine have been used to perform AMES tests to analyze possible health impacts of plant oil operation.
The experimental data show a reduction of particulate matter compared to traditional gasoil which may yield up to 50 % for. The particulate matter shows same primary particle sizes but the agglomerates as collected on TEM grids are different - the plant oil soot particles tend to form larger aggregates [4]. The gaseous emissions of CO and hydrocarbons HC are generally lower compared to the operation with gasoil. However, the NOX emissions are slightly higher. This may be contributed to the measured higher combustion chamber pressures and temperatures when fuelled by plant oils.
Emission samples have been extracted from ESC cycles of 13 step tests to perform the AMES test which give indication on carcinogen substances. The AMES test results gave no indication of mutagenic effects exceeding the detection limits. No significant differences could be found comparing the emissions of plant oil and gasoil operation. Thus, it can be stated that the emission from plant oil operation does not have a health impact different to traditional gas oil. This is in contrast to some other publications — a deeper insight shows that these investigations did not properly modify the engine for plant oils. It is mandatory to make the engine modification to pre-warm the plant oils to approx. 90°C prior to injection. The engine's warm-up phase needs special care to avoid any coking at the injection system and combustion chamber surfaces. The publications where a higher health risk was claimed to be found in the exhaust of plant oil fuels, did not pre-warm the plant oils — cold plant oils have been injected in the combustion chamber instead. This results in incomplete atomization and incomplete combustion with a lot of hazardous emission species (see also [4,11]. Such an operation will damage the engine after relatively short times and is, therefore, not realistic.
The investigated fuels had some influence on the engine characteristics. Higher temperatures and pressures in the cylinder have been detected for some plant oils compared to gasoil. This increase is explained by the higher oxygen content within the plant oils.
The three wavelength extinction method (3-WEM) was applied for the on-line particle analysisof suspensions of monodisperse latex beads and polydisperse metal oxide particles of industrialinterest. Comparative measurements were performed by photon correlation spectroscopy (PCS). Thedata of latex particles obtained by 3-WEM and PCS are in good agreement with the manufacture’svalues. Also, the values of oxide particles measured by means of the two techniques are in reasonableagreement despite of the irregular particle shape.Discrepancies are observed by comparing the oxideparticle size results with those of scanning electron microscopy, which is due to the broad sampledistributions and shape irregularities.
Pflanzenöle können einen gewissen Beitrag für eine erneuerbare, nahezu CO2-neutrale Kraftstoffversorgung leisten. Die nicht-veresterten Pflanzenöle haben im Gegensatz zu veresterten Ölen eine günstige Energie- und CO2-Bilanz. Deshalb werden hier die naturbelassenen, aber raffinierten Pflanzenöle auf ihre Eignung als Kraftstoff in Dieselmotoren und deren Emissionen detailliert untersucht. Versuche wurden mit drei verschiedenen Dieselmotoren durchgeführt.
Auxiliary power units (APUs) are used in mobile applications to supply electrical power in the range of 3 to 10 kW. The state of the art generators are driven by a diesel engine at constant speed. They have a low efficiency (high fuel consumption) as they operate mostly in partial load conditions. A higher efficiency for partial loads is feasible by adjusting the speed of the diesel engine to its optimum efficiency. A frequency converter provides a constant electric frequency at variable speed of the generator. The resulting higher investments for such a variable speed generator (VSG) need a proof of economics, which is demonstrated by this investigation.