Refine
Document Type
- Conference Proceeding (54)
- Article (reviewed) (20)
- Part of a Book (5)
- Patent (3)
- Report (2)
- Article (unreviewed) (1)
Conference Type
- Konferenzartikel (54)
Is part of the Bibliography
- yes (85)
Keywords
- Blockchain (6)
- blockchain (4)
- IIoT (3)
- Internet of Things (3)
- IoT security (3)
- Security (3)
- cryptography (3)
- Bearings (2)
- Blockchains (2)
- NB-IoT (2)
Institute
- Fakultät Elektrotechnik, Medizintechnik und Informatik (EMI) (ab 04/2019) (85) (remove)
Open Access
- Closed Access (37)
- Open Access (24)
- Closed (22)
- Gold (8)
- Diamond (4)
- Bronze (2)
Time-Sensitive Networking (TSN) is the most promising time-deterministic wired communication approach for industrial applications. To extend TSN to "IEEE 802.11" wireless networks two challenging problems must be solved: synchronization and scheduling. This paper is focused on the first one. Even though a few solutions already meet the required synchronization accuracies, they are built on expensive hardware that is not suited for mass market products. While next Wi-Fi generation might support the required functionalities, this paper proposes a novel method that makes possible high-precision wireless synchronization using commercial low-cost components. With the proposed solution, a standard deviation of synchronization error of less than 500 ns can be achieved for many use cases and system loads on both CPU and network. This performance is comparable to modern wired real-time field busses, which makes the developed method a significant contribution for the extension of the TSN protocol to the wireless domain.
This paper presents a novel low-jitter interface between a low-cost integrated IEEE802.11 chip and a FPGA. It is designed to be part of system hardware for ultra-precise synchronization between wireless stations. On physical level, it uses Wi-Fi chip coexistence signal lines and UART frame encoding. On its basis, we propose an efficient communication protocol providing precise timestamping of incoming frames and internal diagnostic mechanisms for detecting communication faults. Meanwhile it is simple enough to be implemented both in low-cost FPGA and commodity IEEE802.11 chip firmware. The results of computer simulation shows that developed FPGA implementation of the proposed protocol can precisely timestamp incoming frames as well as detect most of communication errors even in conditions of high interference. The probability of undetected errors was investigated. The results of this analysis are significant for the development of novel wireless synchronization hardware.
Hybrid low-voltage physical unclonable function based on inkjet-printed metal-oxide transistors
(2020)
Modern society is striving for digital connectivity that demands information security. As an emerging technology, printed electronics is a key enabler for novel device types with free form factors, customizability, and the potential for large-area fabrication while being seamlessly integrated into our everyday environment. At present, information security is mainly based on software algorithms that use pseudo random numbers. In this regard, hardware-intrinsic security primitives, such as physical unclonable functions, are very promising to provide inherent security features comparable to biometrical data. Device-specific, random intrinsic variations are exploited to generate unique secure identifiers. Here, we introduce a hybrid physical unclonable function, combining silicon and printed electronics technologies, based on metal oxide thin film devices. Our system exploits the inherent randomness of printed materials due to surface roughness, film morphology and the resulting electrical characteristics. The security primitive provides high intrinsic variation, is non-volatile, scalable and exhibits nearly ideal uniqueness.
The development of Internet of Things (IoT) embedded devices is proliferating, especially in the smart home automation system. However, the devices unfortunately are imposing overhead on the IoT network. Thus, the Internet Engineering Task Force (IETF) have introduced the IPv6 Low-Power Wireless Personal Area Network (6LoWPAN) to provide a solution to this constraint. 6LoWPAN is an Internet Protocol (IP) based communication where it allows each device to connect to the Internet directly. As a result, the power consumption is reduced. However, the limitation of data transmission frame size of the IPv6 Routing Protocol for Low-power and Lossy Network’s (RPL’s) had made it to be the running overhead, and thus consequently degrades the performance of the network in terms of Quality of Service (QoS), especially in a large network. Therefore, HRPL was developed to enhance the RPL protocol to minimize redundant retransmission that causes the routing overhead. We introduced the T-Cut Off Delay to set the limit of the delay and the H field to respond to actions taken within the T-Cut Off Delay. Thus, this paper presents the comparison performance assessment of HRPL between simulation and real-world scenarios (6LoWPAN Smart Home System (6LoSH) testbed) in validating the HRPL functionalities. Our results show that HRPL had successfully reduced the routing overhead when implemented in 6LoSH. The observed Control Traffic Overhead (CTO) packet difference between each experiment is 7.1%, and the convergence time is 9.3%. Further research is recommended to be conducted for these metrics: latency, Packet Delivery Ratio (PDR), and throughput.
The authentication method of electronic devices, based on individual forms of correlograms of their internal electric noises, is well-known. Specific physical differences in the components – for example, caused by variations in production quality – cause specific electrical signals, i.e. electric noise, in the electronic device. It is possible to obtain this information and to identify the specific differences of the individual devices using an embedded analog-to-digital converter (ADC). These investigations confirm the possibility to identify and authenticate electronic devices using bit templates, calculated from the sequence of values of the normalized autocorrelation function of noise. Experiments have been performed using personal computers. The probability of correct identification and authentication increases with increasing noise recording duration. As a result of these experiments, an accuracy of 98.1% was achieved for a 1 second-long registration of EM for a set of investigated computers.
Time Sensitive Networking (TSN) provides mechanisms to enable deterministic and real-time networking in industrial networks. Configuration of these mechanisms is key to fully deploy and integrate TSN in the networks. The IEEE 802.1 Qcc standard has proposed different configuration models to implement a TSN configuration. Up until now, TSN and its configuration have been explored mostly for Ethernet-based industrial networks. However, they are still considered “work-in-progress” for wireless networks. This work focuses on the fully centralized model and describes a generic concept to enable the configuration of TSN mechanisms in wireless industrial networks. To this end, a configuration entity is implemented to conFigure the wireless end stations to satisfy their requirements. The proposed solution is then validated with the Digital Enhanced Cordless Telecommunication ultra-low energy (DECT ULE) wireless communication protocol.
With the increasing degree of interconnectivity in industrial factories, security becomes more and more the most important stepping-stone towards wide adoption of the Industrial Internet of Things (IIoT). This paper summarizes the most important aspects of one keynote of DESSERT2020 conference. It highlights the ongoing and open research activities on the different levels, from novel cryptographic algorithms over security protocol integration and testing to security architectures for the full lifetime of devices and systems. It includes an overview of the research activities at the authors' institute.
RETIS – Real-Time Sensitive Wireless Communication Solution for Industrial Control Applications
(2020)
Ultra-Reliable Low Latency Communications (URLLC) has been always a vital component of many industrial applications. The paper proposes a new wireless URLLC solution called RETIS, which is suitable for factory automation and fast process control applications, where low latency, low jitter, and high data exchange rates are mandatory. In the paper, we describe the communication protocol as well as the hardware structure of the network nodes for implementing the required functionality. Many techniques enabling fast, reliable wireless transmissions are used – short Transmission Time Interval (TTI), Time-Division Multiple Access (TDMA), MIMO, optional duplicated data transfer, Forward Error Correction (FEC), ACK mechanism. Preliminary tests show that reliable end-to-end latency down to 350 μs and packet exchange rate up to 4 kHz can be reached (using quadruple MIMO and standard IEEE 802.15.4 PHY at 250 kbit/s).
In recent years, predictive maintenance tasks, especially for bearings, have become increasingly important. Solutions for these use cases concentrate on the classification of faults and the estimation of the Remaining Useful Life (RUL). As of today, these solutions suffer from a lack of training samples. In addition, these solutions often require high-frequency accelerometers, incurring significant costs. To overcome these challenges, this research proposes a combined classification and RUL estimation solution based on a Convolutional Neural Network (CNN) and a Long Short-Term Memory (LSTM) network. This solution relies on a hybrid feature extraction approach, making it especially appropriate for low-cost accelerometers with low sampling frequencies. In addition, it uses transfer learning to be suitable for applications with only a few training samples.
TSN, or Time Sensitive Networking, is becoming an essential technology for integrated networks, enabling deterministic and best effort traffic to coexist on the same infrastructure. In order to properly configure, run and secure such TSN, monitoring functionality is a must. The TSN standard already has some preparations to provide such functionality and there are different methods to choose from. We implemented different methods to measure the time synchronisation accuracy between devices as a C library and compared the measurement results. Furthermore, the library has been integrated into the ControlTSN engineering framework.