Refine
Document Type
- Conference Proceeding (9)
- Article (unreviewed) (1)
- Report (1)
Conference Type
- Konferenzartikel (9)
Is part of the Bibliography
- yes (11)
Keywords
- Eingebettetes System (1)
- Fahrzeug (1)
- Fernüberwachung (1)
- Netzwerk (1)
- Niedrige Energie (1)
- Paketlogistik (1)
- Sensortechnik (1)
- Sicherheitstechnik (1)
- Simulation (1)
- TTCN3 (1)
Institute
Open Access
- Open Access (11) (remove)
The Metering Bus, also known as M-Bus, is a European standard EN13757-3 for reading out metering devices, like electricity, water, gas, or heat meters. Although real-life M-Bus networks can reach a significant size and complexity, only very simple protocol analyzers are available to observe and maintain such networks. In order to provide developers and installers with the ability to analyze the real bus signals easily, a web-based monitoring tool for the M-Bus has been designed and implemented. Combined with a physical bus interface it allows for measuring and recording the bus signals. For this at first a circuit has been developed, which transforms the voltage and current-modulated M-Bus signals to a voltage signal that can be read by a standard ADC and processed by an MCU. The bus signals and packets are displayed using a web server, which analyzes and classifies the frame fragments. As an additional feature an oscilloscope functionality is included in order to visualize the physical signal on the bus. This paper describes the development of the read-out circuit for the Wired M-Bus and the data recovery.
Eine kontinuierliche Überwachung von Ethernet-Leitungne beugt Maschinenausfällen in der Industrie vor. Aktuell fehlen jedoch geiegnete Methoden, um diese Überwachung flächendeckend durchzuführen. Im Projekt Ko²SiBus wurde deshalb ein kostengünstiges Verfahren zur kontinuierlichen Überwachung von Ethernet-Leitungen entwickelt.
The research project Ko-TAG [2], as part of the research initiative Ko-FAS [1], funded by the German Ministry of Economics and Technologies (BMWi), deals with the development of a wireless cooperative sensor system that shall pro-vide a benefit to current driver assistance systems (DAS) and traffic safety applications (TSA). The system’s primary function is the localization of vulnerable road users (VRU) e.g. pedestrians and powered two-wheelers, using communication signals, but can also serve as pre-crash (surround) safety system among vehicles. The main difference of this project, compared to previous ones that dealt with this topic, e.g. the AMULETT project, is an underlying FPGA based Hardware-Software co-design. The platform drives a real-time capable communication protocol that enables highly scalable network topologies fulfilling the hard real-time requirements of the single localization processes. Additionally it allows the exchange of further data (e.g. sensor data) to support the accident pre-diction process and the channel arbitration, and thus supports true cooperative sensing. This paper gives an overview of the project’s current system design as well as of the implementations of the key HDL entities supporting the software parts of the communication protocol. Furthermore, an approach for the dynamic reconfiguration of the devices is described, which provides several topology setups using a single PCB design.
Environmental Monitoring is an attractive application field for Wireless Sensor Network (WSN). Water Level Monitoring helps to increase the efficiency of water distribution and management. In Pakistan, the world’s largest irrigation system covers 90.000 km of channels which needs to be monitored and managed on different levels. Especially the sensor systems for the small distribution channels need to be low energy and low cost. The distribution presents a technical solution for a communication system which is developed in a research project being co-funded by German Academic Exchange Service (DAAD). The communication module is based on IEEE-802.15.4 transceivers which are enhanced through Wake-On-Radio (WOR) to combine low-energy and real-time behavior. On higher layers, IPv6 (6LoWPAN) and corresponding routing protocols like Routing Protocol for Low power and Lossy Networks (RPL) can extend range of the network. The data are stored in a database and can be viewed online via a web interface. Of course, also automatic data analysis can be performed.
The IEEE802.11p standard describes a protocol for car-to-X and mainly for car-to-car-communication. It has found its place in hardware and firmware implementations and is currently tested in various field tests. In the research project Ko-TAG, which is part of the research initiative Ko-FAS, cooperative sensor technology is developed and its benefit for traffic safety applications is evaluated. A secondary radar principle based on communication signals enables localization of objects with simultaneous data transmission. It mainly concentrates on the detection of pedestrians and other vulnerable road users (VRU), but also supports pre crash safety applications. The Ko-TAG proposal enriches the current IEEE802.11p real-time characteristics needed for precise time-of-flight real-time localization. This contribution describes the development of a subsystem, which extends the functionality of IEEE802.11p and fits into the regulatory schemes. It discusses the approach for definition and verification of the protocol design, while maintaining the close coexistence with existing IEEE802.11p subsystems. System simulations were performed and hardware was implemented. The next step will be field measurements to verify the simulation results.
Institute of Reliable Embedded Systems and Communication Electronics, Offenburg University of Applied Sciences, Germany has developed an automated testing environment, Automated Physical TestBeds (APTB), for analyzing the performance of wireless systems and its supporting protocols. Wireless physical networking nodes can connect to this APTB and the antenna output of this attaches with the RF waveguides. To model the RF environment this RF waveguides then establish wired connection among RF elements like splitters, attenuators and switches. In such kind of set up it’s well possible to vary the path characteristics by altering the attenuators and switches. The major advantage of using APTB is the possibility of isolated, well controlled, repeatable test environment in various conditions to run statistical analysis and even to execute regression tests. This paper provides an overview of the design and implementation of APTB, demonstrates its ability to automate test cases, and its efficiency.
Wireless communication systems more and more become part of our daily live. Especially with the Internet of Things (IoT) the overall connectivity increases rapidly since everyday objects become part of the global network. For this purpose several new wireless protocols have arisen, whereas 6LoWPAN (IPv6 over Low power Wireless Personal Area Networks) can be seen as one of the most important protocols within this sector. Originally designed on top of the IEEE802.15.4 standard it is a subject to various adaptions that will allow to use 6LoWPAN over different technologies; e.g. DECT Ultra Low Energy (ULE). Although this high connectivity offers a lot of new possibilities, there are several requirements and pitfalls coming along with such new systems. With an increasing number of connected devices the interoperability between different providers is one of the biggest challenges, which makes it necessary to verify the functionality and stability of the devices and the network. Therefore testing becomes one of the key components that decides on success or failure of such a system. Although there are several protocol implementations commonly available; e.g., for IoT based systems, there is still a lack of according tools and environments as well as for functional and conformance testing. This article describes the architecture and functioning of the proposed test framework based on Testing and Test Control Notation Version 3 (TTCN-3) for 6LoWPAN over ULE networks.
Schlussbericht VanAssist
(2021)
Die neueste Generation von programmierbaren Logikbausteinen verfügt neben den konfigurierbaren Logikzellen über einen oder mehrere leistungsfähige Mikroprozessoren. In dieser Arbeit wird gezeigt, wie ein bestehendes Zwei-Chip-System auf einen Xilinx Zynq 7000 mit zwei ARM A9-Cores migriert wird. Bei dem System handelt es sich um das „GPS-gestützte Kreisel-system ADMA“ des Unternehmens GeneSys. Die neue Lösung verbessert den Datenaustausch zwischen dem ersten Mikroprozessor zur digitalen Signalverarbeitung und dem zweiten Prozessor zur Ablaufsteuerung durch ein Shared Memory. Für die schnelle und echtzeitfähige Datenübertragung werden zahlreiche hochbitratige Schnittstellengenutzt.
OPC UA (Open Platform Communications Unified Architecture) is already a well-known concept used widely in the automation industry. In the area of factory automation, OPC UA models the underlying field devices such as sensors and actuators in an OPC UA server to allow connecting OPC UA clients to access device-specific information via a standardized information model. One of the requirements of the OPC UA server to represent field device data using its information model is to have advanced knowledge about the properties of the field devices in the form of device descriptions. The international standard IEC 61804 specifies EDDL (Electronic Device Description Language) as a generic language for describing the properties of field devices. In this paper, the authors describe a possibility to dynamically map and integrate field device descriptions based on EDDL into OPCUA.