Refine
Document Type
- Conference Proceeding (6)
- Article (reviewed) (4)
- Part of a Book (1)
Conference Type
- Konferenzartikel (5)
- Konferenz-Abstract (1)
Language
- English (11)
Has Fulltext
- no (11)
Is part of the Bibliography
- yes (11)
Keywords
- Acoustical properties (1)
- Akustische Oberflächenwelle (1)
- Crystal structure (1)
- Epitaxy (1)
- Finite-Elemente-Methode (1)
- Finite-element analysis (1)
- Interdigital transducers (1)
- Rayleigh waves (1)
- SAW-Bauelement (1)
- Signaltechnik (1)
Institute
Open Access
- Closed Access (11) (remove)
Recently a P-matrix and COM formalism was presented, which predicts third order intermodulation (IMD3) and triple beat with good accuracy and needs only a single nonlinearity constant. This formalism describes frequency dependence correctly. In this work the dependence of this nonlinearity constant on metalization ratio is investigated for aluminum metalization on LiTaO 3 (YXl)/42°. By comparison to test devices the nonlinearity constant is shown to be largely independent of metalization ratio. The nonlinear effect, however, strongly depends on metalization ratio, which is well described by the model. The linearity of a duplexer is optimized by reduction of metalization ratio and redesign of Tx branch topology.
The growing complexity in RF front-ends, which support carrier aggregation and a growing number of frequency bands, leads to tightened nonlinearity requirements in all sub-components. The generation of third order intermodulation products (IMD3) are typical problems caused by the non-linearity of SAW devices. In the present work, we investigate temperature compensating (TC) SAW devices on Lithium Niobate-rot128YX. An accurate FEM simulation model [1] is employed, which allows to better understand the origin of nonlinearities in such acoustic devices.
In a recent paper it has been shown that the effective nonlinear constant which is used in a P-Matrix approach to describe third-order intermodulation (IMD3) in surface acoustic wave (SAW) devices can be obtained from finite element (FEM) calculations of a periodic cell using nonlinear tensor data [1]. In this paper we extend this FEM calculation and show that the IMD3 of an infinite periodic array of electrodes on a piezoelectric substrate can be directly simulated in the sagittal plane. This direct approach opens the way for a FEM based simulation of nonlinearities for finite and generalized structures avoiding the simplifications of phenomenological approaches.
Increasing power density causes increased self-generation of harmonics and intermodulation. As this leads to violations of the strict linearity requirements, especially for carrier aggregation (CA), the nonlinearity must be considered in the design process of RF devices. This raises the demand of accurate simulation models. Linear and nonlinear P-Matrix/COM models are used during the design due to their fast simulation times and accurate results. However, the finite element method (FEM) is useful to get a deeper insight in the device's nonlinearities, as the total field distributions can be visualized. The FE method requires complete sets of material tensors, which are unknown for most relevant materials in nonlinear micro-acoustics. In this work, we perform nonlinear FEM simulations, which allow the calculation of nonlinear field distributions of a lithium tantalate based layered SAW system up to third order. We aim at achieving good correspondence to measured data and determine the contributions of each material layer to the nonlinear signals. Therefore, we use approximations circumventing the issue of limited higher order tensor data. Experimental data for the third order nonlinearity is shown to validate the presented approach.
Laser ultrasound was used to determine dispersion curves of surface acoustic waves on a Si (001) surface covered by AlScN films with a scandium content between 0 and 41%. By including off-symmetry directions for wavevectors, all five independent elastic constants of the film were extracted from the measurements. Results for their dependence on the Sc content are presented and compared to corresponding data in the literature, obtained by alternative experimental methods or by ab-initio calculations.
Propagation of acoustic waves is considered in a system consisting of two stiff quarter-spaces connected by a planar soft layer. The two quarter-spaces and the layer form a half-space with a planar surface. In a numerical study, surface waves have been found and analyzed in this system with displacements that are localized not only at the surface, but also in the soft layer. In addition to the semi-analytical finite element method, an alternative approach based on an expansion of the displacement field in a double series of Laguerre functions and Legendre polynomials has been applied.
It is shown that a number of branches of the mode spectrum can be interpreted and remarkably well described by perturbation theory, where the zero-order modes are the wedge waves guided at a rectangular edge of the stiff quarter-spaces or waves guided at the edge of a soft plate with rigid surfaces.
For elastic moduli and densities corresponding to the material combination PMMA–silicone–PMMA, at least one of the branches in the dispersion relation of surface waves trapped in the soft layer exhibits a zero-group velocity point.
Potential applications of these 1D guided surface waves in non-destructive evaluation are discussed.
Partial substitution of Al atoms with Sc in wurtzite AlN crystals increases the piezoelectric constants. This leads to an increased electromechanical coupling, which is required for high bandwidths in piezo-acoustic filters. The crystal bonds in Ah-xScxN (AlScN) are softened as function of Sc atomic percentage x, leading to reduction of phase velocity in the film. Combining high Sc content AlScN films with high velocity substrates favors higher order guided surface acoustic wave (SAW) modes [1]. This study investigates higher order SAW modes in epitaxial AlScN on sapphire (Al2O3). Their dispersion for Pt metallized epitaxial AlScN films on Al2O3was computed for two different propagation directions. Computed phase velocity dispersion branches were experimentally verified by the characterization of fabricated SAW resonators. The results indicated four wave modes for the propagation direction (0°, 0°, 0°), featuring 3D polarized displacement fields. The sensitivity of the wave modes to the elastic constants of AlScN was investigated. It was shown that due to the 3D polarization of the waves, all elastic constants have an influence on the phase velocity and can be measured by suitable weighting functions in material constant extraction procedures.
Among the various types of guided acoustic waves, acoustic wedge waves are non-diffractive and non-dispersive. Both properties make them susceptible to nonlinear effects. Investigations have recently been focused on effects of second-order nonlinearity in connection with anisotropy. The current status of these investigations is reviewed in the context of earlier work on nonlinear properties of two-dimensional guided acoustic waves, in particular surface waves. The role of weak dispersion, leading to solitary waves, is also discussed. For anti-symmetric flexural wedge waves propagating in isotropic media or in anisotropic media with reflection symmetry with respect to the wedge’s mid-plane, an evolution equation is derived that accounts for an effective third-order nonlinearity of acoustic wedge waves. For the kernel functions occurring in the nonlinear terms of this equation, expressions in terms of overlap integrals with Laguerre functions are provided, which allow for their quantitative numerical evaluation. First numerical results for the efficiency of third-harmonic generation of flexural wedge waves are presented.
High-precision signal processing algorithm to evaluate SAW properties as a function of temperature
(2013)
This paper presents a signal processing algorithm which accurately evaluates the SAW properties of a substrate as functions of temperature. The investigated acoustic properties are group velocity, phase velocity, propagation loss, and coupling coefficient. With several measurements carried out at different temperatures, we obtain the temperature dependency of the SAW properties. The analysis algorithm starts by reading the transfer functions of short and long delay lines. The analysis algorithm determines the center frequency of the delay lines and obtains the delay time difference between the short and long delay lines. The extracted parameters are then used to calculate the acoustic properties of the SAW material. To validate the algorithm, its accuracy is studied by determining the error in the calculating delay time difference, center frequency, and group velocity.