Refine
Document Type
Conference Type
- Konferenzartikel (3)
Is part of the Bibliography
- yes (34) (remove)
Keywords
- 3D printing (3)
- CPC (2)
- Plastizität (2)
- Wärmepumpe (2)
- anterior cruciate ligament (2)
- biomechanics (2)
- change of direction (2)
- cutting (2)
- cyclic loading (2)
- injury prevention (2)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (34) (remove)
Open Access
- Gold (34) (remove)
This paper will introduce the open-source model MyPyPSA-Ger, a myopic optimization model developed to represent the German energy system with a detailed mapping of the electricity sector, on a highly disaggregated level, spatially and temporally, with regional differences and investment limitations. Furthermore, this paper will give new outlooks on the German federal government 2050 emissions goals of the electricity sector to become greenhouse gas neutral by proposing new CO2 allowance strategies. Moreover, the regional differences in Germany will be discussed, their role and impact on the energy transition, and which regions and states will drive the renewable energy utilization forward.
Following a scenario-based analysis, the results point out the major keystones of the energy transition path from 2020 to 2050. Solar, onshore wind, and gas-fired power plants will play a fundamental role in the future electricity systems. Biomass, run of river, and offshore wind technologies will be utilized in the system as base-load generation technologies. Solar and onshore wind will be installed almost everywhere in Germany. However, due to the nature of Germany’s weather and geographical features, the southern and northern regions will play a more important role in the energy transition.
Higher CO2 allowance costs will help achieve the 1.5-degree-target of the electricity system and will allow for a rapid transition. Moreover, the more expensive, and the earlier the CO2 tax is applied to the system, the less it will cost for the energy transition, and the more emissions will be saved throughout the transition period. An earlier phase-out of coal power plants is not necessary with high CO2 taxes, due to the change in power plant’s unit commitment, as they prioritize gas before coal power plants. Having moderate to low CO2 allowance cost or no clear transition policy will be more expensive and the CO2 budget will be exceeded. Nonetheless, even with no policy, renewables still dominate the energy mix of the future.
However, maintaining the maximum historical installation rates of both national and regional levels, with the current emissions reduction strategy, will not be enough to reach the level of climate-neutral electricity system. Therefore, national and regional installation requirements to achieve the federal government emission reduction goals are determined. Energy strategies and decision makers will have to resolve great challenges in order to stay in line with the 1.5-degree-target.
Most recently, the federal government in Germany published new climate goals in order reach climate neutrality by 2045. This paper demonstrates a path to a cost optimal energy supply system for the German power grid until the year 2050. With special regard to regionality, the system is based on yearly myopic optimization with the required energy system transformation measures and the associated system costs. The results point out, that energy storage systems (ESS) are fundamental for renewables integration in order to have a feasible energy transition. Moreover, the investment in storage technologies increased the usage of the solar and wind technologies. Solar energy investments were highly accompanied with the installation of short-term battery storage. Longer-term storage technologies, such as H2, were accompanied with high installations of wind technologies. The results pointed out that hydrogen investments are expected to overrule short-term batteries if their cost continues to decrease sharply. Moreover, with a strong presence of ESS in the energy system, biomass energy is expected to be completely ruled out from the energy mix. With the current emission reduction strategy and without a strong presence of large scale ESS into the system, it is unlikely that the Paris agreement 2° C target by 2050 will be achieved, let alone the 1.5° C.
A novel peptidyl-lys metalloendopeptidase (Tc-LysN) from Tramates coccinea was recombinantly expressed in Komagataella phaffii using the native pro-protein sequence. The peptidase was secreted into the culture broth as zymogen (~38 kDa) and mature enzyme (~19.8 kDa) simultaneously. The mature Tc-LysN was purified to homogeneity with a single step anion-exchange chromatography at pH 7.2. N-terminal sequencing using TMTpro Zero and mass spectrometry of the mature Tc-LysN indicated that the pro-peptide was cleaved between the amino acid positions 184 and 185 at the Kex2 cleavage site present in the native pro-protein sequence. The pH optimum of Tc-LysN was determined to be 5.0 while it maintained ≥60% activity between pH values 4.5—7.5 and ≥30% activity between pH values 8.5—10.0, indicating its broad applicability. The temperature maximum of Tc-LysN was determined to be 60 °C. After 18 h of incubation at 80 °C, Tc-LysN still retained ~20% activity. Organic solvents such as methanol and acetonitrile, at concentrations as high as 40% (v/v), were found to enhance Tc-LysN’s activity up to ~100% and ~50%, respectively. Tc-LysN’s thermostability, ability to withstand up to 8 M urea, tolerance to high concentrations of organic solvents, and an acidic pH optimum make it a viable candidate to be employed in proteomics workflows in which alkaline conditions might pose a challenge. The nano-LC-MS/MS analysis revealed bovine serum albumin (BSA)’s sequence coverage of 84% using Tc-LysN which was comparable to the sequence coverage of 90% by trypsin peptides.
Photovoltaic-heat pump (PV-HP) combinations with battery and energy management systems are becoming increasingly popular due to their ability to increase the autarchy and utilization of self-generated PV electricity. This trend is driven by the ongoing electrification of the heating sector and the growing disparity between growing electricity costs and reducing feed-in tariffs in Germany. Smart control strategies can be employed to control and optimize the heat pump operation to achieve higher self-consumption of PV electricity. This work presents the evaluation results of a smart-grid ready controlled PV-HP-battery system in a single-family household in Germany, using 1-minute-high-resolution field measurement data. Within 12 months evaluation period, a self-consumption of 43% was determined. The solar fraction of the HP amounts to 36%, enabled also due to higher set temperatures for space heating and domestic hot water production. Accordingly, the SPF decreases by 4.0% the space heating and by 5.7% in the domestic hot water mode. The combined seasonal performance factor for the heat pump system increases from 4.2 to 6.7, when only considering the electricity taken from the grid and disregarding the locally generated electricity supplied from photovoltaic and battery units.
For the treatment of bone defects, biodegradable, compressive biomaterials are needed as replacements that degrade as the bone regenerates. The problem with existing materials has either been their insufficient mechanical strength or the excessive differences in their elastic modulus, leading to stress shielding and eventual failure. In this study, the compressive strength of CPC ceramics (with a layer thickness of more than 12 layers) was compared with sintered β-TCP ceramics. It was assumed that as the number of layers increased, the mechanical strength of 3D-printed scaffolds would increase toward the value of sintered ceramics. In addition, the influence of the needle inner diameter on the mechanical strength was investigated. Circular scaffolds with 20, 25, 30, and 45 layers were 3D printed using a 3D bioplotter, solidified in a water-saturated atmosphere for 3 days, and then tested for compressive strength together with a β-TCP sintered ceramic using a Zwick universal testing machine. The 3D-printed scaffolds had a compressive strength of 41.56 ± 7.12 MPa, which was significantly higher than that of the sintered ceramic (24.16 ± 4.44 MPa). The 3D-printed scaffolds with round geometry reached or exceeded the upper limit of the compressive strength of cancellous bone toward substantia compacta. In addition, CPC scaffolds exhibited more bone-like compressibility than the comparable β-TCP sintered ceramic, demonstrating that the mechanical properties of CPC scaffolds are more similar to bone than sintered β-TCP ceramics.
Young female handball players represent a high-risk population for anterior cruciate ligament (ACL) injuries. While the external knee abduction moment (KAM) is known to be a risk factor, it is unclear how cutting technique affects KAMs in sport-specific cutting maneuvers. Further, the effect of added game specificity (e.g., catching a ball or faking defenders) on KAMs and cutting technique remains unknown. Therefore, this study aimed: (i) to test if athletes grouped into different clusters of peak KAMs produced during three sport-specific fake-and-cut tasks of different complexities differ in cutting technique, and (ii) to test whether technique variables change with task complexity. Fifty-one female handball players (67.0 ± 7.7 kg, 1.70 ± 0.06 m, 19.2 ± 3.4 years) were recruited. Athletes performed at least five successful handball-specific sidestep cuts of three different complexities ranging from simple pre-planned fake-and-cut maneuvers to catching a ball and performing an unanticipated fake-and-cut maneuver with dynamic defenders. A k-means cluster algorithm with squared Euclidean distance metric was applied to the KAMs of all three tasks. The optimal cluster number of koptimal = 2 was calculated using the average silhouette width. Statistical differences in technique variables between the two clusters and the tasks were analyzed using repeated-measures ANOVAs (task complexity) with nested groupings (clusters). KAMs differed by 64.5%, on average, between clusters. When pooling all tasks, athletes with high KAMs showed 3.4° more knee valgus, 16.9% higher downward and 8.4% higher resultant velocity at initial ground contact, and 20.5% higher vertical ground reaction forces at peak KAM. Unlike most other variables, knee valgus angle was not affected by task complexity, likely due to it being part of inherent movement strategies and partly determined by anatomy. Since the high KAM cluster showed higher vertical center of mass excursions and knee valgus angles in all tasks, it is likely that this is part of an automated motor program developed over the players' careers. Based on these results, reducing knee valgus and downward velocity bears the potential to mitigate knee joint loading and therefore ACL injury risk.
In the literature, many studies have described the 3D printing of ceramic-based scaffolds (e.g., printing with calcium phosphate cement) in the form of linear structures with layer rotations of 90°, although no right angles can be found in the human body. Therefore, this work focuses on the adaptation of biological shapes, including a layer rotation of only 1°. Sample shapes were printed with calcium phosphate cement using a 3D Bioplotter from EnvisionTec. Both straight and wavy spokes were printed in a round structure with 12 layers. Depending on the strand diameter (200 and 250 µm needle inner diameter) and strand arrangement, maximum failure loads of 444.86 ± 169.39 N for samples without subsequent setting in PBS up to 1280.88 ± 538.66 N after setting in PBS could be achieved.
Batteries typically consist of multiple individual cells connected in series. Here we demonstrate single-cell state of charge (SOC) and state of health (SOH) diagnosis in a 24 V class lithium-ion battery. To this goal, we introduce and apply a novel, highly efficient algorithm based on a voltage-controlled model (VCM). The battery, consisting of eight single cells, is cycled over a duration of five months under a simple cycling protocol between 20 % and 100 % SOC. The cell-to-cell standard deviations obtained with the novel algorithm were 1.25 SOC-% and 1.07 SOH-% at beginning of cycling. A cell-averaged capacity loss of 9.9 % after five months cycling was observed. While the accuracy of single-cell SOC estimation was limited (probably owed to the flat voltage characteristics of the lithium iron phosphate, LFP, chemistry investigated here), single-cell SOH estimation showed a high accuracy (2.09 SOH-% mean absolute error compared to laboratory reference tests). Because the algorithm does not require observers, filters, or neural networks, it is computationally very efficient (three seconds analysis time for the complete data set consisting of eight cells with approx. 780.000 measurement points per cell).
Objective: This paper deals with the design and the optimization of mechatronic devices.
Introduction: Comparing with existing works, the design approach presented in this paper aims to integrate optimization in the design phase of complex mechatronic systems in order to increase the efficiency of this method.
Methods: To solve this problem, a novel mechatronic system design approach has been developed in order to take the multidisciplinary aspect and to consider optimization as a tool that can be used within the embodiment design process to build mechatronic solutions from a set of solution concepts designed with innovative or routine design methods.
Conclusions: This approach has then been applied to the design and optimization of a wind turbine system that can be implemented to autonomously supply a mountain cottage.
Die multimedialen Informationsdienste im Internet werden immer umfangreicher und umfassender, wobei auch die nur in gedruckter Form vorliegenden Dokumente von den Bibliotheken digitalisiert und ins Netz gestellt werden. Über Online-Dokumentenverwaltungen oder Suchmaschinen können diese Dokumente gefunden und dann in gängigen Formaten wie z.B. PDF bereitgestellt werden.
Dieser Artikel beleuchtet die Funktionsweise der Humboldt Digital Library, die seit mehr als zehn Jahren Dokumente von Alexander von Humboldt in englischer Übersetzung im Web als HDL (Humboldt Digital Library) kostenfrei zur Verfügung stellt. Anders als eine digitale Bibliothek werden dabei allerdings nicht nur digitalisierte Dokumente als Scan oder PDF bereitgestellt, sondern der Text als solcher und in vernetzter Form verfügbar gemacht.
Das System gleicht damit eher einem Informationssystem als einer digitalen Bibliothek, was sich auch in den verfügbaren Funktionen zur Auffindung von Texten in unterschiedlichen Versionen und Übersetzungen, Vergleichen von Absätzen verschiedener Dokumente oder der Darstellung von Bilden in ihrem Kontext widerspiegelt.
Die Entwicklung von dynamischen Hyperlinks auf der Basis der einzelnen Textabsätze der Humboldt‘schen Werke in Form von Media Assets ermöglicht eine Nutzung der Programmierschnittstelle von Google Maps zur geographischen wie auch textinhaltlichen Navigation.
Über den Service einer digitalen Bibliothek hinausgehend, bietet die HDL den Prototypen eines mehrdimensionalen Informationssystems, das mit dynamischen Strukturen arbeitet und umfangreiche thematische Auswertungen und Vergleiche ermöglicht.