Refine
Document Type
- Article (reviewed) (24) (remove)
Language
- English (24)
Has Fulltext
- no (24) (remove)
Is part of the Bibliography
- yes (24)
Keywords
- copper oxide (1)
- diode modeling (1)
- indium oxide (1)
- nickel oxide (1)
- oxide electronics (1)
- pn-diode (1)
- printed electronics (1)
Institute
- Fakultät Elektrotechnik, Medizintechnik und Informatik (EMI) (ab 04/2019) (24) (remove)
Open Access
- Closed Access (16)
- Open Access (6)
Electrolyte-gated thin-film transistors (EGTs) with indium oxide channel, and expected lifetime of three months, enable low-voltage operation (~1 V) in the field of printed electronics (PEs). The channel width of our printed EGTs is varied between 200 and 1000 μm, whereas a channel length between 10 and 100 μm is used. Due to the lack of uniform performance p-type metal oxide semiconductors, n-type EGTs and passive elements are used to design circuits. For logic gates, transistor-resistor logic has been employed so far, but depletion and enhancement-mode EGTs in a transistor-transistor logic boost the circuit performance in terms of delay and signal swing. In this article, the threshold voltage of the EGT, which determines the operation mode, is tuned through sizing of the EGTs channel geometry. The feasibility of both transistor operation modes is demonstrated for logic gates and ring oscillators. An inverter operating at a supply voltage of 1 V shows a maximum gain of 9.6 and a propagation delay time of 0.7 ms, which represents an improvement of ~ 2x for the gain and oscillation frequency, in comparison with the resistor-transistor logic design. Moreover, the power consumption is reduced by 6x.
Oxide semiconductors have the potential to increase the performance of inkjet printed microelectronic devices such as field-effect transistors (FETs), due to their high electron mobilities. Typical metal oxides are n-type semiconductors, while p-type oxides, although realizable, exhibit lower carriermobilities. Therefore, the circuit design based on oxide semiconductors is mostly in n-type logic only. Here we present an inkjet printed pn-diode based on p- and n-type oxide semiconductors.Copper oxide or nickel oxide is used as p-typesemiconductor whereas n-typesemiconductor is realized with indium oxide. Themeasurements show that the pn-diodes operate in the voltage window typical for printed electronics and the emission coefficient is 1.505 and 2.199 for the copper oxide based and nickel oxidebased pn-diode, respectively.Furthermore, a pn-diode model is developed and integrable into a circuit simulator.
In the domain of printed electronics (PE), field-effect transistors (FETs) with an oxide semiconductor channel are very promising. In particular, the use of high gate-capacitance of the composite solid polymer electrolytes (CSPEs) as a gate-insulator ensures extremely low voltage requirements. Besides high gate capacitance, such CSPEs are proven to be easily printable, stable in air over wide temperature ranges, and possess high ion conductivity. These CSPEs can be sensitive to moisture, especially for high surface-to-volume ratio printed thin films. In this paper, we provide a comprehensive experimental study on the effect of humidity on CSPE-gated single transistors. At the circuit level, the performance of ring oscillators (ROs) has been compared for various humidity conditions. The experimental results of the electrolyte-gated FETs (EGFETs) demonstrate rather comparable currents between 30%-90% humidity levels. However, the shifted transistor parameters lead to a significant performance change of the RO frequency behavior. The study in this paper shows the need of an impermeable encapsulation for the CSPE-gated FETs to ensure identical performance at all humidity conditions.
Printed electrolyte-gated oxide electronics is an emerging electronic technology in the low voltage regime (≤1 V). Whereas in the past mainly dielectrics have been used for gating the transistors, many recent approaches employ the advantages of solution processable, solid polymer electrolytes, or ion gels that provide high gate capacitances produced by a Helmholtz double layer, allowing for low-voltage operation. Herein, with special focus on work performed at KIT recent advances in building electronic circuits based on indium oxide, n-type electrolyte-gated field-effect transistors (EGFETs) are reviewed. When integrated into ring oscillator circuits a digital performance ranging from 250 Hz at 1 V up to 1 kHz is achieved. Sequential circuits such as memory cells are also demonstrated. More complex circuits are feasible but remain challenging also because of the high variability of the printed devices. However, the device inherent variability can be even exploited in security circuits such as physically unclonable functions (PUFs), which output a reliable and unique, device specific, digital response signal. As an overall advantage of the technology all the presented circuits can operate at very low supply voltages (0.6 V), which is crucial for low-power printed electronics applications.
Printed electronics (PE) circuits have several advantages over silicon counterparts for the applications where mechanical flexibility, extremely low-cost, large area, and custom fabrication are required. The custom (personalized) fabrication is a key feature of this technology, enabling customization per application, even in small quantities due to low-cost printing compared with lithography. However, the personalized and on-demand fabrication, the non-standard circuit design, and the limited number of printing layers with larger geometries compared with traditional silicon chip manufacturing open doors for new and unique reverse engineering (RE) schemes for this technology. In this paper, we present a robust RE methodology based on supervised machine learning, starting from image acquisition all the way to netlist extraction. The results show that the proposed RE methodology can reverse engineer the PE circuits with very limited manual effort and is robust against non-standard circuit design, customized layouts, and high variations resulting from the inherent properties of PE manufacturing processes.
Printed electronics (PE) is a fast-growing field with promising applications in wearables, smart sensors, and smart cards, since it provides mechanical flexibility, and low-cost, on-demand, and customizable fabrication. To secure the operation of these applications, true random number generators (TRNGs) are required to generate unpredictable bits for cryptographic functions and padding. However, since the additive fabrication process of the PE circuits results in high intrinsic variations due to the random dispersion of the printed inks on the substrate, constructing a printed TRNG is challenging. In this article, we exploit the additive customizable fabrication feature of inkjet printing to design a TRNG based on electrolyte-gated field-effect transistors (EGFETs). We also propose a printed resistor tuning flow for the TRNG circuit to mitigate the overall process variation of the TRNG so that the generated bits are mostly based on the random noise in the circuit, providing a true random behavior. The simulation results show that the overall process variation of the TRNGs is mitigated by 110 times, and the generated bitstream of the tuned TRNGs passes the National Institute of Standards and Technology - Statistical Test Suite. For the proof of concept, the proposed TRNG circuit was fabricated and tuned. The characterization results of the tuned TRNGs prove that the TRNGs generate random bitstreams at the supply voltage of down to 0.5 V. Hence, the proposed TRNG design is suitable to secure low-power applications in this domain.
Printed electronics (PE) enables disruptive applications in wearables, smart sensors, and healthcare since it provides mechanical flexibility, low cost, and on-demand fabrication. The progress in PE raises trust issues in the supply chain and vulnerability to reverse engineering (RE) attacks. Recently, RE attacks on PE circuits have been successfully performed, pointing out the need for countermeasures against RE, such as camouflaging. In this article, we propose a printed camouflaged logic cell that can be inserted into PE circuits to thwart RE. The proposed cell is based on three components achieved by changing the fabrication process that exploits the additive manufacturing feature of PE. These components are optically look-alike, while their electrical behaviors are different, functioning as a transistor, short, and open. The properties of the proposed cell and standard PE cells are compared in terms of voltage swing, delay, power consumption, and area. Moreover, the proposed camouflaged cell is fabricated and characterized to prove its functionality. Furthermore, numerous camouflaged components are fabricated, and their (in)distinguishability is assessed to validate their optical similarities based on the recent RE attacks on PE. The results show that the proposed cell is a promising candidate to be utilized in camouflaging PE circuits with negligible overhead.
Advances in printed electronics (PE) enables new applications, particularly in ultra-low-cost domains. However, achieving high-throughput printing processes and manufacturing yield is one of the major challenges in the large-scale integration of PE technology. In this article, we present a programmable printed circuit based on an efficient printed lookup table (pLUT) to address these challenges by combining the advantages of the high-throughput advanced printing and maskless point-of-use final configuration printing. We propose a novel pLUT design which is more efficient in PE realization compared to existing LUT designs. The proposed pLUT design is simulated, fabricated, and programmed as different logic functions with inkjet printed conductive ink to prove that it can realize digital circuit functionality with the use of programmability features. The measurements show that the fabricated LUT design is operable at 1 V.
Printed electronics can benefit from the deployment of electrolytesas gate insulators,which enables a high gate capacitance per unit area (1–10 μFcm−2) due to the formation of electrical double layers (EDLs). Consequently, electrolyte-gated field-effect transistors (EGFETs) attain high-charge carrier densities already in the subvoltage regime, allowing for low-voltage operation of circuits and systems. This article presents a systematic study of lumped terminal capacitances of printed electrolyte-gated transistors under various dc bias conditions. We perform voltage-dependent impedancemeasurements and separate extrinsic components from the lumped terminal capacitance.
The proposed Meyer-like capacitance model, which also accounts for the nonquasi-static (NQS) effect, agrees well with experimental data. Finally, to verify the model, we implement it in Verilog-A and simulate the transient response of an inverter and a ring oscillator circuit. Simulation results are in good agreement with the measurement data of fabricated devices.
Electrolyte-gated, printed field-effect transistors exhibit high charge carrier densities in the channel and thus high on-currents at low operating voltages, allowing for the low-power operation of such devices. This behavior is due to the high area-specific capacitance of the device, in which the electrolyte takes the role of the dielectric layer of classical architectures. In this paper, we investigate intrinsic double-layer capacitances of ink-jet printed electrolyte-gated inorganic field-effect transistors in both in-plane and top-gate architectures by means of voltage-dependent impedance spectroscopy. By comparison with deembedding structures, we separate the intrinsic properties of the double-layer capacitance at the transistor channel from parasitic effects and deduce accurate estimates for the double-layer capacitance based on an equivalent circuit fitting. Based on these results, we have performed simulations of the electrolyte cutoff frequency as a function of electrolyte and gate resistances, showing that the top-gate architecture has the potential to reach the kilohertz regime with proper optimization of materials and printing process. Our findings additionally enable accurate modeling of the frequency-dependent capacitance of electrolyte/ion gel-gated devices as required in the small-signal analysis in the circuit simulation.