Refine
Document Type
Conference Type
- Konferenzartikel (6)
- Konferenz-Abstract (1)
Has Fulltext
- no (12)
Is part of the Bibliography
- yes (12)
Keywords
- Emission (2)
- Partikel (2)
- Verbrennungsmotor (2)
- FFF (1)
- Korrelation (1)
- Materialermüdung (1)
- Messung (1)
- Ruß (1)
- Sensortechnik (1)
- Wellenlänge (1)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (12) (remove)
Open Access
- Closed Access (12) (remove)
Soot particles emitted from a light duty (LD) Volkswagen diesel engine running at different operating points (speed and torque levels) are analyzed for mean size determination using a laser‐based three Wavelength Extinction Method (3‐WEM). For this reason, collected soot samples are suspended using an appropriate sample preparation technique with optimized conditions of sonication as it revealed its effect on the soot mean particle size measured by 3‐WEM.
An online Scanning Mobility Particle Analyzer (SMPS) is also used to measure soot emission at identical engine operating points. Size values obtained from SMPS are lower than those of suspended soot samples obtained from 3‐WEM. The size discrepancies are mainly related to the required sample preparation procedure employed for 3‐WEM measurements. The engine operating points affect, differently, the size measurements obtained from SMPS and 3‐WEM.
Sedimentation Field‐Flow Fractionation (SdFFF) is used for density determination of soot samples based on size measurements of fractions collected at peak maxima of fractograms using the off‐line hyphenation with 3‐WEM. It is assumed that a size dependent separation of soot particles occurred with a uniform particle density over the whole size distribution. An average density value is used for the conversion of soot fractograms to size distributions. Discrepancies are also found with size distribution profiles obtained from SMPS for the same engine operating points, due to the sample preparation procedure employed for SdFFF measurements.
A prototype multiwavelength sensor able to characterise soot emissions in Diesel exhaust in terms of size and concentration has been tested against other methods for diesel particle measurements like electrical mobility sizing (SMPS) and raw exhaust gravimetric sampling (RES). Measurements carried out with the prototype sensor were correlated with the SMPS by assuming spherical and/or fractal aggregate morphology of the particles. Correlation of RES gravimetric data against the sensor and the SMPS led to the calculation of the solid density for soot particles to be 2.3 gr/cm3.
Specific prototypes of sedimentation field flow fractionation devices (SdFFF) have been developed with relative success for cell sorting. However, no data are available to compare these apparatus with commercial ones. In order to compare with other devices mainly used for non-biological species, biocompatible systems were used for standard particle (latex: 3–10 μm of different size dispersities) separation development. In order to enhance size dependent separations, channels of reduced thickness were used (80 and 100 μm) and channel/carrier-phase equilibration procedures were necessary. For sample injection, the use of inlet tubing linked to the FFF accumulation wall, common for cell sorting, can be extended to latex species when they are eluted in the Steric Hyperlayer elution mode. It avoids any primary relaxation steps (stop flow injection procedure) simplifying series of elution processing. Mixtures composed of four different monodispersed latex beads can be eluted in 6 min with 100 μm channel thickness.
The three wavelength extinction method (3-WEM) was applied for the on-line particle analysisof suspensions of monodisperse latex beads and polydisperse metal oxide particles of industrialinterest. Comparative measurements were performed by photon correlation spectroscopy (PCS). Thedata of latex particles obtained by 3-WEM and PCS are in good agreement with the manufacture’svalues. Also, the values of oxide particles measured by means of the two techniques are in reasonableagreement despite of the irregular particle shape.Discrepancies are observed by comparing the oxideparticle size results with those of scanning electron microscopy, which is due to the broad sampledistributions and shape irregularities.
Non-Esterified Plant Oils as Fuel -Engine Characteristics, Emissions and Mutagenic effects of PM-
(2009)
Plant oils may be used as a sustainable, nearly CO2 neutral fuel for diesel engines. This work investigates experimentally the particulate and gaseous emissions of diesel engines fuelled with non-esterified, pure plant oils with the quality standard of DIN V 51605 (Weihen-stephan RK-Qualitätsstandard 05/2000). The data are collected from three engines:
Common rail passenger car engine from OPEL AG
Truck engine from VOLVO
Truck engine from MAN AG
All engines have been correctly adjusted to plant oil operation.
The OPEL and VOLVO engines served for the basic investigations. The emissions of the MAN engine have been used to perform AMES tests to analyze possible health impacts of plant oil operation.
The experimental data show a reduction of particulate matter compared to traditional gasoil which may yield up to 50 % for. The particulate matter shows same primary particle sizes but the agglomerates as collected on TEM grids are different - the plant oil soot particles tend to form larger aggregates [4]. The gaseous emissions of CO and hydrocarbons HC are generally lower compared to the operation with gasoil. However, the NOX emissions are slightly higher. This may be contributed to the measured higher combustion chamber pressures and temperatures when fuelled by plant oils.
Emission samples have been extracted from ESC cycles of 13 step tests to perform the AMES test which give indication on carcinogen substances. The AMES test results gave no indication of mutagenic effects exceeding the detection limits. No significant differences could be found comparing the emissions of plant oil and gasoil operation. Thus, it can be stated that the emission from plant oil operation does not have a health impact different to traditional gas oil. This is in contrast to some other publications — a deeper insight shows that these investigations did not properly modify the engine for plant oils. It is mandatory to make the engine modification to pre-warm the plant oils to approx. 90°C prior to injection. The engine's warm-up phase needs special care to avoid any coking at the injection system and combustion chamber surfaces. The publications where a higher health risk was claimed to be found in the exhaust of plant oil fuels, did not pre-warm the plant oils — cold plant oils have been injected in the combustion chamber instead. This results in incomplete atomization and incomplete combustion with a lot of hazardous emission species (see also [4,11]. Such an operation will damage the engine after relatively short times and is, therefore, not realistic.
The investigated fuels had some influence on the engine characteristics. Higher temperatures and pressures in the cylinder have been detected for some plant oils compared to gasoil. This increase is explained by the higher oxygen content within the plant oils.