Refine
Year of publication
- 2009 (6) (remove)
Document Type
Conference Type
- Konferenz-Abstract (1)
- Konferenz-Poster (1)
Language
- English (6) (remove)
Is part of the Bibliography
- yes (6) (remove)
Keywords
- Absorption (1)
- Chlorwasserstoff (1)
- Eigenschaft (1)
- Hybridantrieb (1)
- Schwefeldioxid (1)
- Wirbelrohr ; Fließverhalten (1)
- hybrid drive systems (1)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (6) (remove)
Open Access
- Open Access (6) (remove)
Plant oils may be used as a sustainable, nearly CO2neutral fuel for diesel engines. This work investigates experimentally the particulate and gaseous emissions of diesel engines fuelled with different non-esterified, pure plant oils. The data are collected from three engines: a) Common rail 1.7 liter passenger car engine from Opel AG b) 12.8 liter truck engine from VOLVO c) Truck engine from MAN AG.
The emissions of the MAN engine have been used to perform AMES tests to analyze possible health impacts of plant oil operation. Finally, all emission results with plant oils have been compared to traditional gas oils.
Hydrogen chloride and sulphur dioxide are gaseous by-products of chloridization processes that employ thionyl chloride. Absorption would be a feasible method to clean the rich gas stream. Two serial connectable absorption columns were equipped with the latest generation of packings to effect product recovery. Therefore, several tests concerning the baffle properties had to be performed. In the first experimental section, the hydraulic parameters pressure drop and hold-up were investigated. The hold up value range of the new baffles Raschig Super Ring (RSR) and Raschig Super Pak (RSP) was clearly below that of the former installed packing, Raschig Ring (RR). However, due to the low maximal flow rate, the range of stagnation and flooding could not be measured. The maximal measured pressure drop value was, for RR, only 0.3 mbar/m, which is very low compared to the measurement error. Batch experiments, where the waste gases were produced by reaction of thionyl chloride in water, showed that for the steady state determination of the separation steps it is advisable to use just one column in simplex mode with a defined gas supply by a gas cylinder. The HTU determination for RSR and a HCl/H2O system delivered a value of HTUHCl,OG = 0.14 ± 0.01 m with a variation coefficient of 24.2%.
Hybrid drives for automotive application are extensively discussed. In contrast, the company HEINZMANN, the University of Karlsruhe and the University of Applied Sciences Offenburg concentrate on hybrid drives for industrial, offroad purposes in a joint project. These applications promise a much higher fuel saving potential, particularly if highly frequent load cycles are present. Hybrid drive systems offer additional advantages including reduced exhaust aftertreatment requirements due to engine downsizing, better engine dynamics, emissions and noise reduction.
This study focuses on the experimental and numerical investigations on a commercial Ranque-Hilsch vortex tube. Ranque-Hilsch vortex tubes have many applications in industry and production as they can generate a very cold flow just from pressurized air .e.g. machine tool cooling. Main objective of this study is the energy separation in the flow field which results in a temperature drop on the cold exit of the tube. This was investigated experimentally by measuring the outlet temperature on the cold exit and the pressure drop on the flow restrictor valve on the hot exit. At a pressure drop of 0.5 bar the vortex tube showed the best performance by reaching a cold exit temperature of –16.7 °C. The Inlet flow was pressurised air at 20 °C and 6 bar.<br /> The numerical analysis was carried out by full 3D steady state CFD-simulation using the commercial software ANSYS CFX 11.0. The three dimensional model represented a 120° sector of the tube using periodic boundary conditions. A comparison between different turbulence models (k – å, RNG k – å, k – ù, SST) was carried out. The classic k – å two layer turbulence model showed the best results compared to the experiment. The energy separation and the drop in cold exit temperature are highest when the viscous work term is included into the energy equation. These effects of including the viscous work term into the energy separation have also been investigated.