Refine
Year of publication
Document Type
- Article (reviewed) (28)
- Conference Proceeding (13)
- Article (unreviewed) (3)
- Report (2)
- Part of a Book (1)
- Contribution to a Periodical (1)
Conference Type
- Konferenzartikel (13)
Is part of the Bibliography
- yes (48)
Keywords
- Plastizität (12)
- Ermüdung (9)
- Mikrostruktur (6)
- Materialermüdung (5)
- Stahl (5)
- Eisenguss (4)
- Simulation (4)
- Thermomechanik (4)
- Finite-Elemente-Methode (3)
- Rissausbreitung (3)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (45)
- CRT - Campus Research & Transfer (3)
- Fakultät Elektrotechnik und Informationstechnik (E+I) (bis 03/2019) (2)
- Fakultät Wirtschaft (W) (1)
- IDEeP - Institute for Digital Engineering and Production (ab 12.10.2022) (1)
- INES - Institut für nachhaltige Energiesysteme (1)
- Zentrale Einrichtungen (1)
Open Access
- Closed Access (20)
- Open Access (13)
- Closed (10)
- Gold (2)
- Diamond (1)
HiSiMo cast irons are frequently used as material for high temperature components in engines as e.g. exhaust manifolds and turbo chargers. These components must withstand severe cyclic mechanical and thermal loads throughout their life cycle. The combination of thermal transients with mechanical load cycles results in a complex evolution of damage, leading to thermomechanical fatigue (TMF) of the material and, after a certain number of loading cycles, to failure of the component. In Part I of the paper, a fracture mechanics model for TMF life prediction was developed based on results of uniaxial tests. In this paper (Part II), the model is formulated for three-dimensional stress states, so that it can be applied in a post-processing step of a finite-element analysis. To obtain reliable stresses and (time dependent plastic) strains in the finite-element calculation, a time and temperature dependent plasticity model is applied which takes non-linear kinematic hardening into account. The material properties of the model are identified from the results of the uniaxial test. The plasticity model and the TMF life model are applied to assess the lifetime of an exhaust manifold.
HiSiMo cast irons are frequently used as material for high temperature components in engines as e.g. exhaust manifolds and turbo chargers. These components must withstand severe cyclic mechanical and thermal loads throughout their service life. The combination of thermal transients with mechanical load cycles results in a complex evolution of damage, leading to thermomechanical fatigue (TMF) of the material and, after a certain number of loading cycles, to failure of the component. In this paper (Part I), the low-cycle fatigue (LCF) and TMF properties of HiSiMo are investigated in uniaxial tests and the damage mechanisms are addressed. On the basis of the experimental results a fatigue life model is developed which is based on elastic, plastic and creep fracture mechanics results of short cracks, so that time and temperature dependent effects on damage are taken into account. The model can be used to estimate the fatigue life of components by means of finite-element calculations (Part II of the paper).
In this work, time-independent and time-dependent plasticity models are presented that are well suited for the calculation of stresses and strains with the finite-element method to assess the low-cycle and thermomechanical fatigue life of engineering components. The focus are plasticity models that are available in finite-element programs nowadays as standard material models and describe isotropic and kinematic hardening, strain-rate dependency as well as static recovery of hardening. For the presented models, aspects relevant for the application of the models are addressed as the determination of the material properties and the numerical implementation. Nevertheless, the plasticity models are also embedded in the thermodynamic framework used for the derivation of thermodynamically consistent plasticity models. Only uniaxial formulations are used to achieve a good readability and preventing the use of tensors.
In this paper, the J-integral is derived for temperature-dependent elastic–plastic materials described by incremental plasticity. It is implemented using the equivalent domain integral method for assessment of three-dimensional cracks based on results of finite-element calculations. The J-integral considers contributions from inhomogeneous temperature fields and temperature-dependent elastic and plastic material properties as well as from gradients in the plastic strains and the hardening variables. Different energy densities are considered, the Helmholtz free energy and the stress-working density, providing a physical meaning of the J-integral as a fracture criteria for crack growth. Results obtained for a plate with two different crack configurations each loaded by a cool-down thermal shock show domain-independence of the incremental J-integral for different energy densities even for high temperature gradients and significant temperature-dependence of the yield stress and the hardening exponent in the presence of large scale yielding. Hence, the derived J-integral is an appropriate parameter for the assessment of cracks in thermomechanically loaded components.
Turbocharger housings in internal combustion engines are subjected to severe mechanical and thermal cyclic loads throughout their life-time or during engine testing. The combination of thermal transients and mechanical load cycling results in a complex evolution of damage, leading to thermo-mechanical fatigue (TMF) of the material. For the computational TMF life assessment of high temperature components, the DTMF model can provide reliable TMF life predictions. The model is based on a short fatigue crack growth law and uses local finite-element (FE) results to predict the number of cycles to failure for a technical crack. In engine applications, it is nowadays often acceptable to have short cracks as long as they do not propagate and cause loss of function of the component. Thus, it is necessary to predict not only potential crack locations and the corresponding number of cycles for a technical crack, but also to determine subsequent crack growth or even a possible crack arrest. In this work, a method is proposed that allows the simulation of TMF crack growth in high temperature components using FE simulations and non-linear fracture mechanics (NLFM).
A NLFM based crack growth simulation method is described. This method starts with the FE analysis of a component. In this paper, the method is demonstrated for an automotive turbocharger housing subjected to TMF loading. A transient elastic-viscoplastic FE analysis is used to simulate four heating and cooling cycles of an engine test. The stresses, inelastic strains, and temperature histories from the FEA are then used to perform TMF life predictions using the standard DTMF model. The crack position and the crack plane of critical hotspots are then identified. Simulated cracks are inserted at the hotspots. For the model demonstrated, cracks were inserted at two hotspot locations. The ΔJ integral is computed as a fracture mechanics parameter at each point along the crack-front, and the crack extension of each point is then evaluated, allowing the crack to grow iteratively. The paper concludes with a comparison of the crack growth curves for both hotspots with experimental results.
In order to make material design processes more efficient in the future, the underlying multidimensional process parameter spaces must be systematically explored using digitalisation techniques such as machine learning (ML) and digital simulation. In this paper we shortly review essential concepts for the digitalisation of electrodeposition processes with a special focus on chromium plating from trivalent electrolytes.
In this paper, the temperature dependent cyclic mechanical properties of the martensitic hot work tool steel 1.2367 after tempering are investigated. To this end, hardness measurements as well as monotonic and cyclic tests at temperatures in the range from room temperature to 650 °C are performed on material tempered for different tempering times and temperatures. To describe the observed time and temperature dependent softening during tempering a kinetic model for the evolution of the mean size of secondary carbides based on Ostwald ripening is developed. Furthermore, mechanism-based as well as phenomenological relations for the cyclic mechanical properties of the Ramberg-Osgood model depending on carbide size and temperature are introduced. A good overall agreement of the measured and the calculated stress-strain hysteresis loops for different temperatures and heat treatments is obtained using the determined material properties of the kinetic and mechanical model.
Hot forging dies are subjected to high cyclic thermo-mechanical loads. In critical areas, the occurring stresses can exceed the material’s yield limit. Additionally, loading at high temperatures leads to thermal softening of the used martensitic materials. These effects can result in an early crack initiation and unexpected failure of the dies, usually described as thermo-mechanical fatigue (TMF). In previous works, a temperature-dependent cyclic plasticity model for the martensitic hot forging tool steel 1.2367 (X38CrMoV5-3) was developed and implemented in the finite element (FE)-software Abaqus. However, in the forging industry, application-specific software is usually used to ensure cost-efficient numerical process design. Therefore, a new implementation for the FE-software Simufact Forming 16.0 is presented in this work. The results are compared and validated with the original implementation by means of a numerical compression test and a cyclic simulation is calculated with Simufact Forming.
Significant improvements in module performance are possible via implementation of multi-wire electrodes. This is economically sound as long as the mechanical yield of the production is maintained. While flat ribbons have a relatively large contact area to exert forces onto the solar cell, wires with round cross section reduce this contact area considerably – in theory to an infinitively thin line. Therefore, the local stresses induced by the electrodes might increase to a point that mechanical production yields suffer unacceptably.
In this paper, we assess this issue by an analytical mechanical model as well as experiments with an encapsulant-free N.I.C.E. test setup. From these, we can derive estimations for the relationship between lay-up accuracy and expected breakage losses. This paves the way for cost-optimized choices of handling equipment in industrial N.I.C.E.-wire production lines.
In this paper, an unconditionally stable algorithm for the numerical integration and finite-element implementation of a class of pressure dependent plasticity models with nonlinear isotropic and kinematic hardening is presented. Existing algorithms are improved in the sense that the number of equations to be solved iteratively is significantly reduced. This is achieved by exploitation of the structure of Armstrong-Frederik-type kinematic hardening laws. The consistent material tangent is derived analytically and compared to the numerically computed tangent in order to validate the implementation. The performance of the new algorithm is compared to an existing one that does not consider the possibility of reducing the number of unknowns to be iterated. The algorithm is used to implement a time and temperature dependent cast iron plasticity model, which is based on the pressure dependent Gurson model, in the finite-element program ABAQUS. The implementation is applied to compute stresses and strains in a large-scale finite-element model of a three cylinder engine block. This computation proofs the applicability of the algorithm in industrial practice that is of interest in applied sciences.
Due to higher combustion chamber temperatures and pressures in efficient combustion engines, both the high-cycle and thermomechanical fatigue loads on service life-critical components, such as the cylinder head, are increasing. Material comparisons and analysis of damage behavior are very expensive and time-consuming using component tests. This study therefore develops a test method for cylinder head materials that takes into account the combined loading conditions from the above-mentioned loads and allows realistic temperature transients and gradients on near-component samples. The near-component cylinder head sample represents the failure-critical exhaust valve crosspiece and is tested in a test rig specially designed with the aid of conjugate heat transfer simulations. In the test rig, the sample is subjected to thermal stress by a hot gas burner and to mechanical stress by a high-frequency pulsator. Optical crack detection allows permanent observation of fatigue crack growth and crack closure during the test. Fractographic and metallo-graphic examinations of the fracture areas as well as analyses of the damage patterns show that loads close to engine operation can be set in this way and their influences on the damage can be monitored.
Für langfaserverstärkte Thermoplaste (LFT) wird ein repräsentatives Volumenelement (RVE) für FEM-Simulationen generiert. Dies geschieht unter Berücksichtigung von mikrostrukturellen Kenngrößen wie Faserorientierungsverteilung, -volumengehalt und -längenverteilung, die für einen charakteristischen Werkstoffzustand experimentell ermittelt wurden. Mittels Mikrostruktursimulationen wird das Kriechverhalten von LFT untersucht. Das viskoelastische Verhalten der Matrix wird experimentell an Substanzproben aus Polypropylen ermittelt und in die RVE-Simulationen mit einem modifizierten Burgers-Modell implementiert. Schließlich werden die Rechnungen mit verschiedenen, fiktiven sowie experimentell ermittelten Faserlängenverteilungen mit Kriechversuchen am LFT verglichen. Es zeigt sich eine starke Abhängigkeit des Kriechverhaltens von der Faserlänge und eine hohe Prognosegüte der Simulationen, die die experimentell ermittelte Längenverteilung berücksichtigen.
In this paper, the effect of the polycrystalline microstructure on crack-tip opening displacement and crack closure is investigated for microstructural short plane strain fatigue cracks using the finite-element method. To this end, cracks are introduced in synthetically generated microstructures and the grain properties are described using a single crystal plasticity model with kinematic hardening. Additionally, finite-element calculations without resolved microstructure and von Mises plasticity with kinematic hardening are performed. Fully-reversed strain-controlled cyclic loadings are considered under large-scale yielding conditions as typical for low-cycle fatigue problems. The crack opening stress and the cyclic crack-tip opening displacement are significantly influenced by the local grain structure. While the stabilized crack opening stresses obtained with the microstructure-based finite-element model are in good accordance with the von Mises plasticity results, the differences in the cyclic crack opening displacement are addressed to the asymmetric plastic strain fields in the plastic wake behind the crack-tip of the microstructure-based model. The asymmetric plastic strain fields result in discontinuous and premature contact of the crack flanks.
In dem abgeschlossenen Vorhaben „Entwicklung von Rechenmodellen zur Lebensdauervorhersage von Motorbauteilen unter thermisch-mechanischer Ermüdungsbeanspruchung“ der Forschungsvereinigung Verbrennungskraftmaschinen e. V. (FVV) wurde am Fraunhofer Institut für Werkstoffmechanik IWM in Freiburg ein Materialmodell zur Lebensdauervorhersage thermomechanisch belasteter Komponenten entwickelt. Das Modell basiert auf einem viskoplastischen Verformungsmodell für Eisengusswerkstoffe und einem mechanismenbasierten Modell für Mikrorisswachstum zur Lebensdauervorhersage.
This paper reports on the evolution of cracks in the cylinder heads of a large V8 Diesel engine during cyclic engine tests. The observations are compared with the predictions of a lifetime model for combined thermo-mechanical (TMF) and high cycle fatigue (HCF) loading, which is based on a fracture mechanics analysis of microcrack growth in viscoplastic solids and assumes that the crack advance per cycle is proportional to the cyclic crack tip opening displacement. Since the material of the cylinder heads, the cast iron EN-GJV450, exhibits the typical features of cast iron, namely pressure dependence of the yield stress, dilatancy and tension-compression asymmetry, the Gurson model is applied and combined with the viscoplastic Chaboche model. This constitutive model together with the lifetime model is implemented into a finite element code as a user defined material routine. Published model parameters for the considered cast iron are used to carry out the simulation of the engine test. This simulation comprises a CFD analysis to determine the heat transfer coefficients, a thermal analysis of the load cycle and the mechanical analysis. The thermal analysis reproduces the temperatures at various measuring points sufficiently accurately. Finally, the mechanical analysis predicts the location and orientation of the cracks in the valve bridges correctly in all cases. However, the lifetime predictions are rather conservative compared to the tests (by a factor of 1 to 5 in lifetime). This is discussed and explained by the fact that the cracks were detected in the tests only when they had already spread over a substantial fraction of the valve bridge width. To describe this situation a long-crack analysis would be necessary, which is not yet included in the applied lifetime model.