Refine
Year of publication
- 2012 (41) (remove)
Document Type
- Article (reviewed) (11)
- Conference Proceeding (9)
- Part of a Book (7)
- Article (unreviewed) (7)
- Report (2)
- Bachelor Thesis (1)
- Book (1)
- Contribution to a Periodical (1)
- Master's Thesis (1)
- Patent (1)
Conference Type
- Konferenzartikel (7)
- Konferenz-Abstract (1)
- Konferenz-Poster (1)
Keywords
- Adsorption (5)
- Metallorganisches Netzwerk (4)
- Dünnschichtchromatographie (2)
- Kohlendioxid (2)
- "Conditioning"-Film (1)
- 2D-TLC (1)
- Ammoniumverbindungen (1)
- Bauteil (1)
- Belastung (1)
- Biene (1)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (41) (remove)
Open Access
- Closed Access (20)
- Open Access (12)
- Bronze (1)
- Closed (1)
As a basis for the evaluation of hydrogen storage by physisorption, adsorption isotherms of H2 were experimentally determined for several porous materials at 77 K and 298 K at pressures up to 15 MPa. Activated carbons and MOFs were studied as the most promising materials for this purpose. A noble focus was given on how to determine whether a material is feasible for hydrogen storage or not, dealing with an assessment method and the pitfalls and problems of determining the viability. For a quantitative evaluation of the feasibility of sorptive hydrogen storage in a general analysis, it is suggested to compare the stored amount in a theoretical tank filled with adsorbents to the amount of hydrogen stored in the same tank without adsorbents. According to our results, an “ideal” sorbent for hydrogen storage at 77 K is calculated to exhibit a specific surface area of >2580 m2 g−1 and a micropore volume of >1.58 cm3 g−1.
Im Rahmen des Programms Solarthermie2000plus wurde eine begrenzte Anzahl solarthermischer Pilot sowie Forschungs- und Demonstrationsanlagen zur Teildeckung des Wärmebedarfs unterschiedlicher Verbraucher im Niedertemperaturbereich modellhaft gefördert. Mit Solarthermie2000plus führte das BMU im Rahmen des Energieforschungsprogramms der Bundesregierung die langfristig angelegten Forschungsaktivitäten zur thermischen Nutzung der Sonnenenergie des Förderkonzepts Solarthermie-2000 mit neuen Schwerpunkten fort.
Stähle im Bauwesen
(2012)
In vielen Schulgebäuden der Region südlicher Oberrhein - besonders bei solchen, die energetisch saniert wurden und wo der Schulbetrieb auf Ganztagsunterricht umgestellt wurde - zeigt sich seit Beginn dieses Jahrhunderts eine verstärkte Über-hitzungstendenz im Sommer. Im Rahmen der Initiative Forschungskooperation Hochschule/Stadt für mehr Energieeffizienz beim Betrieb öffentlicher Gebäude und Liegenschaften beauftragte die Stadt Offenburg die Forschungsgruppe nachhaltige Energietechnik (Forschungsgruppe net) der Hochschule Offenburg mit der Ausarbeitung eines Konzeptes für die natürliche Gebäudeklimatisierung in Klassenzimmern. Besonderes Augenmerk galt dabei neben bautechnischen Maßnahmen der Ge-bäudeautomation. Da ein vollautomatisierter Betrieb technisch und finanziell für viele kommunalen Betreiber unrealistisch ist, ist zudem die Einbindung der Nutzer und Mitarbeiter vor Ort unerlässlich. Die Ergebnisse aus dem Projekt stehen einer breiten Öffentlichkeit in Form eines Leitfadens zur Verfügung.
Die hohen Anforderungen vor allem an Drehmoment übertragende und mehrfachgekerbte Profilwellen im konstruktiven Umfeld moderner Maschinen zwingen uns, der Frage der Kerbwirkungen sowie Maßnahmen zu deren Milderung erhöhte Aufmerksamkeit zu widmen. Während die Kerbwirkung der geometrischen Einzelkerben bereits recht eingehend erforscht ist, liegen wesentlich komplexere Verhältnisse bei Mehrfachkerben vor, die durch die gegenseitige Beeinflussung mehrerer benachbarter Kerben entstehen. Der hier vorliegende Beitrag beschreibt erste Untersuchungsergebnisse mit der Finite-Elemente-Methode (FEM) zur gegenseitigen Wechselwirkung zweier Kerbformen "Sicherungsringnut und Zahnfußrundung" bei Zahnwellen mit Evolventenflanken nach DIN 5480. Diese Kerbkombination tritt in der Praxis häufig auf. Entsprechende Formzahldiagramme und Gestaltungshinweise werden angegeben und Näherungsformeln für die genauere Formzahlbestimmung je nach Belastungsart aufgestellt.
Der vorliegene Beitrag beschreibt erste Untersuchungsergebnisse mit der Finite-Elemente-Methode (FEM) zur Ermittlung der Kennwerte des bezogenen Spannungsgefälles beim linear-elastischen Werkstoffverhalten für die nach DIN 5480 genormten Zahnwellen mit freiem Auslauf bei Torsion, Biegung und Zug/Druck. Für die Bestimmung von Zwischen-werten werden analytische Näherungsgleichungen aufgestellt.
Die vorliegende Erfindung betrifft eine Messchraube zur Ermittlung von Schraubenbelastungen sowie ein Verfahren zu deren Herstellung. Die Messschraube umfasst mindestens zwei Dehnungsmesssensoren, die so im Schraubenschaft angeordnet und dehnungskinematisch mit dem Schraubenschaft gekoppelt sind, dass sie Dehnungswerte im Schraubenschaft erfassen, aus denenüber konstitutive Materialgesetze Belastungen in mehr als einer Achse im oberen freien Schaftbereich bestimmt werden können. Durch Möglichkeit der Bestimmung mehrachsiger Belastungen lassen sich Schrauben sachgerechter auslegen, so dass die Gefahr von Schraubenbrüchen reduziert wird.
In this work the adsorption of CO2 and CH4 on a series of isoreticular microporous metal–organic frameworks based on 2-substituted imidazolate-4-amide-5-imidates, IFP-1–IFP-6 (IFP = Imidazolate Framework Potsdam), is studied firstly by pure gas adsorption at 273 K. All experimental isotherms can be nicely described by using the Tòth isotherm model and show the preferred adsorption of CO2 over CH4. At low pressures the Tòth isotherm equation exhibits a Henry region, wherefore Henry's law constants for CO2 and CH4 uptake could be determined and ideal selectivity αCO2/CH4 has been calculated. Secondly, selectivities were calculated from mixture data by using nearly equimolar binary mixtures of both gases by a volumetric–chromatographic method to examine the IFPs. Results showed the reliability of the selectivity calculation. Values of αCO2/CH4 around 7.5 for IFP-5 indicate that this material shows much better selectivities than IFP-1, IFP-2, IFP-3, IFP-4 and IFP-6 with slightly lower selectivity αCO2/CH4 = 4–6. The preferred adsorption of CO2 over CH4 especially of IFP-5 and IFP-4 makes these materials suitable for gas separation application.
In cardiac resynchronization therapy (CRT) for heart failure, individualization of the AV delay is essential to improve hemodynamics and to minimize non-responder rate. In patients in sinus rhythm having additional disposition to bradycardia, optimization is necessary for both situations, atrial sensing and pacing. Therefore, echo-optimization is the goldstandard but time consuming. Unfortunately, it depends on the particular CRT systems parameter set if the resulting individually optimal AV delays can be programmed or not. Some CRT systems provide a set of AV delays for DDD operation combined with a set of the pace-sense-compensation to optimize the AV delay in DDD and VDD operation. The pace-sense-compensation (PSC) can be defined by the difference of implant-related interatrial conduction intervals in DDD and VDD operation measured in the esophageal left atrial electrogram. In a cohort of 96 CRT patients we found mean PSC of 59-35ms ranging between 0-143ms. As a consequence, allowing 10ms tolerance, AVD optimization is completely impossible in one of the two modes, VDD or DDD operation, in 34 (35%) or 5 (5%) patients with implants restricting the PSC range to 60ms or 100ms, respectively. Thus, we propose companies to provide CRT systems with programmable pace-sense- compensation between 0ms and 150ms.
Im ersten Teil der vorliegenden Master-Thesis geht es um die Entwicklung einer Low-Power Wireless-Lichtschranke. Der Hardware-Aufbau wird ausführlich beschrieben und Besonderheiten für die Low-Power-Auslegung, wie beispielsweise Power-Management, werden vorgestellt. Optische Einheiten, Power-Management-Einheiten, System-On-Chip und Funkstufe werden ausführlich angesprochen. Die interrupt-gesteuerte und zeitlich optimierte Programmierung wird im Anschluss an den Hardware-Aufbau vorgestellt. Auch hier werden Low-Power-Eigenschaften diskutiert. Die Anbindung der Lichtschranke an einen Hub im 868 MHz ISM Band (engl.: Industrial, Scientific and Medical Band) und die Datenübertragung mittels Bluetooth an einen Computer, sowie die Programmierung einer Anzeige-GUI zur Visualisierung der Funkdaten mit LabVIEW werden weiterführend behandelt. Ergänzend hierzu wird die entwickelte Hardware vermessen und charakterisiert. Die Messergebnisse werden ausgewertet und vorgestellt.
Im zweiten Teil der Master-Thesis geht es um die Entwicklung eines Schulungskonzepts. In der Sick AG halten sich alle Abteilungen (Divisions) beim Entwickeln eines Produktes an einen vorgegebenen Produktentstehungsprozess. Division 1 hat im Rahmen dieses Produktentstehungsprozesses eine Konkretisierung vorgenommen: den Masterplan. Für die Einführung des Masterplans wurde ein teilnehmerorientiertes Schulungskonzept entwickelt. Es wird zuerst auf die Inhalte eingegangen. Im Anschluss werden die Teilnehmer untersucht und Motive und Lernvoraussetzungen charakterisiert. Nachdem diese und weitere Rahmenbedingungen geklärt sind, wird ein didaktisch durchdachtes Schulungskonzept entwickelt, ausführlich vorgestellt und diskutiert.
Biofilme können in technischen Systemen zu Beschädigungen oder Beeinträchtigungen der Leistung des Systems führen. In der Humanmedizin können sie zu Infektionen an Kathetern und Implantat-oberflächen führen. Biofilme bilden sich an Phasengrenzflächen. Der erste Schritt in der Entstehung eines Biofilms ist die Bildung eines "Conditioning"-Films aus Substanzen des umgebenden Mediums. Ein zur Beschichtung von Implantaten eingesetztes Polymer ist Parylen C. Auf akustischen Oberflächenwellen, englisch: surface acoustic wave (SAW), basierende Sensoren zeigen bei Änderungen der Eigenschaften ihrer aktiven Oberfläche eine Änderung ihrer Resonanzfrequenz. Im Rahmen dieser Arbeit wurde überprüft, ob sich SAW-Sensoren zur Echtzeitbeobachtung der Bildung von "Conditioning"-Filmen eignen. Als Vergleichssystem wurden Schwingquarze, englisch: quarz crystal microbalances (QCM), gewählt, da diese ebenfalls gravimetrischen Sensoren bereits zur Beoabachtung von "Conditioning"-Filmen eingesetzt werden. Sensoren beider Systeme wurden mit Parylen C beschichtet und jeweils mit drei relevanten Proteinen des menschlichen Blutplasmas beprobt. Es konnte gezeigt werden, dass sich auf akustischen Oberflächenwellen basierende Sensoren zur Beobachtug der Adsorption von Plasmaproteinen auf Parylen C eignen. Zudem konnten auf SAW-Sensoren reproduzierbar Charakteristiken in den Kurvenverläufen beobachtet werden, welche beim Vergleichssystems nicht sichtbar waren.
Die Hochschule Offenburg begleitet in Zusammenarbeit mit dem Fraunhofer ISE in Freiburg die solar unterstützte Klimatisierung der Deutschen Telekom in Rottweil. Die Anlage wurde im Rahmen des Forschungsvorhabens „Solarthermie2000plus“ vom Bundesumweltministerium gefördert. Inzwischen liegen erste Ergebnisse aus einem Langzeitmonitoring vor.
Unter dem europäischen Programm Intelligent Energy for Europe (IEE) fanden sich acht europäische Partner zusammen, um im Rahmen des Projektes ThermCo Lüftungs‐ und Kühlenergiekonzepte für Nichtwohngebäude mit niedrigem Energieeinsatz im Hinblick auf die Energieeffizienz und den thermischen Raumkomfort zu bewerten. Die Analyse erfolgte auf Basis von detaillierten Langzeitmessungen über ein Betriebsjahr in acht Demonstrationsgebäuden in unterschiedlichen klimatischen Zonen Europas und einer standardisierten Datenauswertung. Im Quervergleich aller acht Gebäude werden die Kühlkonzepte gleichermaßen nach dem thermischen Kühlenergiebezug, dem thermischen Raumkomfort und dem Primärenergieeinsatz für die technische Gebäudeausrüstung und die Beleuchtung bewertet. Ein Energiekonzept ist erst dann zufriedenstellend, wenn mit möglichst geringem Energieeinsatz und bei hoher Anlageneffizienz ein guter thermischer Raumkomfort zur Verfügung gestellt werden kann. Mit entsprechenden Gebäudesignaturen werden diese Parameter in einen Zusammenhang gebracht und die Zielstellung überprüft. Detaillierte Komfortuntersuchungen nach der europäischen Komfortnorm DIN EN 15251:2007‐08 geben Hinweise auf die Wirksamkeit der eingesetzten Kühltechnologien in den jeweiligen Klimazonen. Daraus lassen sich Handlungsempfehlungen ableiten.
Buildings that are cooled and, if applicable, heated by thermo-active building systems (TABS) in combination with environmental energy have been established in the market during the last years. Many successful and efficient examples prove, that these systems can achieve a good thermal room comfort with a high energy efficiency of the plant system using environmental energy (mainly surface-near geothermal energy). However, operating experience and a systematic evaluation of several building projects demonstrate that there is potential improvement in the design, implementation, and operation of TABS systems. The article presents operating experience and a detailed evaluation of the operation performance of several non-residential buildings with thermo-active building systems with respect to thermal comfort and energy efficiency.
An isomorphous series of 10 microporous copper-based metal–organic frameworks (MOFs) with the general formulas ∞3[{Cu3(μ3-OH)(X)}4{Cu2(H2O)2}3(H-R-trz-ia)12] (R = H, CH3, Ph; X2– = SO42–, SeO42–, 2 NO32– (1–8)) and ∞3[{Cu3(μ3-OH)(X)}8{Cu2(H2O)2}6(H-3py-trz-ia)24Cu6]X3 (R = 3py; X2– = SO42–, SeO42– (9, 10)) is presented together with the closely related compounds ∞3[Cu6(μ4-O)(μ3-OH)2(H-Metrz-ia)4][Cu(H2O)6](NO3)2·10H2O (11) and ∞3[Cu2(H-3py-trz-ia)2(H2O)3] (12Cu), which are obtained under similar reaction conditions. The porosity of the series of cubic MOFs with twf-d topology reaches up to 66%. While the diameters of the spherical pores remain unaffected, adsorption measurements show that the pore volume can be fine-tuned by the substituents of the triazolyl isophthalate ligand and choice of the respective copper salt, that is, copper sulfate, selenate, or nitrate.
The newly synthesized Zn4O-based MOF 3∞[Zn4(μ4-O){(Metrz-pba)2mPh}3]·8 DMF (1·8 DMF) of rare tungsten carbide (acs) topology exhibits a porosity of 43% and remarkably high thermal stability up to 430 °C. Single crystal X-ray structure analyses could be performed using as-synthesized as well as desolvated crystals. Besides the solvothermal synthesis of single crystals a scalable synthesis of microcrystalline material of the MOF is reported. Combined TG-MS and solid state NMR measurements reveal the presence of mobile DMF molecules in the pore system of the framework. Adsorption measurements confirm that the pore structure is fully accessible for nitrogen molecules at 77 K. The adsorptive pore volume of 0.41 cm3 g−1 correlates well with the pore volume of 0.43 cm3 g−1 estimated from the single crystal structure.
Die Veränderungen in der Energieversorgung führen zu einer neuen Systemarchitektur der Stromversorgung, die nur durch einen massiven Einsatz von Informations- und Kommunikationstechnologien (IKT) bewältigt werden kann und meist als „Smart Grid“ bezeichnet wird. Während es bereits umfangreiche Forschungsarbeiten und Demonstrationsprojekte zu einzelnen technologischen Komponenten gibt, existieren noch wenige Überlegungen, in welchen technologischen Schritten eine Migration hin zu Smart Grids durchgeführt werden sollte, die sowohl betriebstechnisch zukunftssicher ist, als auch marktgetriebene Innovationen begünstigt. Der Beitrag veranschaulicht die Herleitung solcher Migrationspfade im Rahmen eines schrittweisen Vorgehens. Zunächst werden Zukunftsszenarien für das Jahr 2030 konstruiert, um die maßgeblichen, oft auch nichttechnischen Einflussfaktoren auf das Smart Grid zu identifizieren. Darauf aufbauend werden die wesentlichen IKT-bezogenen Technologiefelder und ihre Zuordnung zu den Domänen der Energiewirtschaft beschrieben. Für jedes Technologiefeld werden die in den nächsten zwei Jahrzehnten denkbaren Entwicklungsstufen ermittelt und deren Abhängigkeit untereinander analysiert. Die gemeinsame Betrachtung von Szenarien, der Entwicklungsstufen der Technologiefelder und deren Interdependenzen führen schließlich zu einer Roadmap, welche die Migrationspfade in das Smart Grid beschreiben. Es lassen sich drei Entwicklungsphasen erkennen: Die Konzeptionsphase, die Integrationsphase und die Fusionsphase. Die präsentierten Ergebnisse entstammen dem Projekt „Future Energy Grid – Migrationspfade ins Internet“, welches vom Bundesministerium für Wirtschaft und Technologie im Rahmen des E-Energy-Programms (Förderkennzeichen 01ME10012A und 01ME10013) gefördert wurde.
Für die Werkstoffe EN GJS700, EN GJV450 und EN GJL250 werden die Lebensdauern unter kombinierter thermomechanischer und hochfrequenter Belastung vorhergesagt. Hierzu wird ein mechanismenbasiertes Lebensdauermodell verwendet, das auf dem Wachstum von Mikrorissen beruht. Das Modell berücksichtigt das Wachstum von Rissen durch nieder- und überlagerte hochfrequente Belastungszyklen. Anhand von einachsigen Ermüdungsversuchen wurden die Parameter des Lebensdauermodells angepasst, sodass eine bestmögliche Lebensdauervorhersage erzielt wird. Dabei stimmen die vorhergesagten Lebensdauern gut mit den experimentell ermittelten Zyklenzahlen zum Versagen überein.
In this paper, the multiaxial formulation of a mechanism-based model for fatigue life prediction is presented whichcan be applied to low-cycle fatigue (LCF) and thermomechanical fatigue (TMF) problems in which high-cycle fa-tigue loadings are superimposed. The model assumes that crack growth is the lifetime limiting mechanism and thatthe crack advance in a loading cycleda/dNcorrelates with the cyclic crack-tip opening displacement ΔCTOD.The multiaxial formulation makes use of fracture mechanics solutions and thus, does not need additional modelparameters quantifying the effect of the multiaxiality. Furthermore, the model includes contributions of HCF on ΔCTODand assesses the effect of the direction of the HCF loadings with respect to LCF or TMF loadings inthe life prediction. The model is implemented into the finite-element program ABAQUS. It is applied to predictthe fatigue life of a thermomechanically loaded notched specimen that should represent the situation between theinlet and outlet bore holes of cylinder heads. A good correlation of the predicted and the measured fatigue lives isobtained.
Limits of quantification of some neonicotinoid insecticides measured by thin-layer chromatography
(2012)
A simple method to quantify the neonicotinoid insecticides nitenpyram, thiamethoxam, acetamiprid, imidacloprid, thiacloprid and clothianidin directly on an HPTLC-plate is presented. As stationary phase silica gel 60 RP-18WF254 s plates were used and a mixture of methyl-t-butyl ether, 2-butanone, NH3 (25%) (5 + 2+0.1, v/v) was used as solvent. All neonicotinoid insecticides show light absorptions below 300 nm. The calculated limits of quantification (LOQ) by UV-detection are in the range from 12 ng to 26 ng on plate depending on the different insecticides.Nitenpyram can be stained using fast blue salt B, forming red zones. The observed LOQ is 25 ng on plate. Acetamiprid can be specifically stained using phenylglyoxylic acid forming a yellow/green fluorescent compound. The LOQ is 52 ng per spot.The compounds thiamethoxam, acetamiprid, thiacloprid and clothianidin can be transformed into blue fluorescing zones, using a relatively new staining solution. This consists of tetraphenylborate and HCl. This is the first publication mentioning that neonicotinoids undergo this reaction. The calculated limits of quantification are in the range from 10 ng to 27 ng on plate.A simple pre-treatment procedure using an acetonitrile extraction and a Chromabond SiOH clean up procedure leads to overall LOQs for bee samples of 48 to 108 µg/Kg. The method can be used to measure neonicotinoid contaminations of bees.
We will present the first example of a two-dimensional scanned TLC-plate, measured by use of a diode-array scanner. A spatial resolution of 250 µm was achieved on plate. The system provides real 2D fluorescence and absorption spectra in the wavelength-range from 190 to 1000 nm with a spectral resolution of greater than 1 nm. A mixture of 12 sulphonamides was separated by using a cyanopropyl-coated silica gel plate (Merck, 1.16464) with the solvent mix of methyl tert-butyl ether-methanol-dichloromethane-cyclohexane-NH3 (25%) (48:2:2:1:1, v/v) in the first and with a mixture of water-acetonitrile-dioxane-ethanol (8:2:1:1, v/v) in the second direction. Both developments were carried out over a distance of 70 mm. A separation number (spot capacity) of 259 was calculated. We discussed a new formula for its calculation in 2D-TLC separations. The drawback of this method is that measuring a 2D-TLC plate needs more than 3 h measurement time.
The present study describes medium-chain-length polyhydroxyalkanoates (mcl-PHAs) production by the Pseudomonas Gl01 strain isolated from mixed microbial communities utilized for PHAs synthesis. A two-step fedbatch fermentation was conducted with glucose and waste rapeseed oil as the main carbon source for obtaining cell growth and mcl-PHAs accumulation, respectively. The results show that the Pseudomonas Gl01 strain is capable of growing and accumulating mcl-PHAs using a waste oily carbon source. The biomass value reached 3.0 g/l of CDW with 20% of PHAs content within 48 h of cultivation. The polymer was purified from lyophilized cells and analyzed by gas chromatography (GC). The results revealed that the monomeric composition of the obtained polyesters depended on the available substrate. When glucose was used in the growth phase, 3-hydroxyundecanoate and 3- hydroxydodecanoate were found in the polymer composition, whereas in the PHAs-accumulating stage, the Pseudomonas Gl01 strain synthesized mcl-PHAs consisting mainly of 3- hydroxyoctanoate and 3-hydroxydecanoate. The transcriptional analysis using reverse-transcription real-time PCR reaction revealed that the phaC1 gene could be transcribed simultaneously to the phaZ gene.
Pure gas adsorption isotherms of CH4 and N2 and their binary mixtures were measured at 273 K, 298 K and 323 K and up to 2 MPa on two different microporous metal–organic frameworks (MOFs), i.e. the commercially available Basolite® A100 and the recently reported copper-based triazolyl benzoate MOF 3∞[Cu(Me-4py-trz-ia)] (1). The Tòth isotherm model and the vacancy solution model were used to describe the experimentally determined isotherms and proved to be well suited for this purpose. While 1 shows a more homogeneous surface with a nearly constant isosteric heat of adsorption of 18–18.5 kJ mol−1 for CH4 and 12–15 kJ mol−1 for N2, the isosteric heat of adsorption at zero coverage for Basolite® A100 is 19 kJ mol−1 for CH4 and 16.2 kJ mol−1 for N2, decreasing significantly with increasing loading. Binary adsorption isotherms were measured gravimetrically to determine the total adsorbed mass of CH4 and N2. The van Ness method was successfully applied to calculate partial loadings from gravimetrically measured binary adsorption isotherms. Further studies by volumetric–chromatographic experiments support the good correlation between experimental data and predictions by the vacancy solution model (VSM-Wilson) and the ideal adsorbed solution theory (IAST) from pure gas isotherms. The experimental selectivities were determined to be αCH4/N2 = 4.0–5.0 for 1, slightly higher than for Basolite® A100 with αCH4/N2 = 3.4–4.5. These values are in good agreement with predictions for ideal selectivities based on Henry's law constants. From the experimental selectivities the potential of both MOFs in gas separation of CH4 from N2 can be derived.
The provisioning of security for highly dynamic wireless networks, as for Car2X applications is still a major topic, as very specific requirements have to be solved. Those include a perfect privacy level and advanced real-time behavior, and the necessity to work with a public infrastructure (PKI) to support secure authentication.
This contribution analyzes these requirements, discusses the existing approaches, performs a gap analysis and elaborates on proposals to fill these gaps. It describes work in progress within the KoFAS-initiative for the development of a cooperative pedestrian protection system (CPPS).
The CO2 uptake on nanoscale AlO(OH) hollow spheres (260 mg g−1) as a new material is comparable to that on many metal–organic frameworks although their specific surface area is much lower (530 m2 g¬1versus 1500–6000 m2g¬1). Suited temperature–pressure cycles allow for reversible storage and separation of CO2 while the CO2 uptake is 4.3-times higher as compared to N2.
Improved separation of highly toxic contact herbicides paraquat (1,1′-dimethyl-4-4′-bipyridinium), diquat (6,7-dihydrodipyridol[ 1,2-a:2′,1′-c]pyrazine-5,8-di-ium), difenzoquat (1,2-dimethyl-3,5-diphenyl-1H-pyrazolium-methyl sulfate), mepiquat (1,1-dimethyl-piperidinium), and chloromequat (2-chloroethyltrimethylammonium) were presented by high-performance thin-layer chromatography (HPTLC). The quantification is based on a derivatization reaction, using sodium tetraphenylborate. Measurements were made in the wavelength range from 500 to 535 nm, using a light-emitting diode (LED) for excitation purposes, which emits very dense light at 365 nm. For calculations, a new theory of standard addition method was used, thus leading to a minimal error if exactly the same amount of sample content is added as a standard. The method provides a fast and inexpensive approach to quantification of the five most important quats used for plant protection purposes. The method works reliably because it takes into account losses during pre-treatment procedure. The method meets the European legislation limits for paraquat and diquat in drinking water according to United States Environmental Protection Agency (US EPA) method 549.2 which are 680 ng L−1 for paraquat and 720 ng L−1 for diquat. The method of standard addition in planar chromatography can be beneficially used to reduce systematic errors. Although recovery rates of 33.7% to 65.2% are observed, calculated contents according to the method of standard addition lie between 69% and 127% of the theoretical amounts.
Die Weltwirtschaftskrise 2008 hat mit ihrer zeitweisen Verknappung von Acetonitril eindringlich gezeigt, dass man nicht nur auf eine einzige chromatographische Methode setzten sollte. Genau dies wird aber im Augenblick getan, denn Industrie und Forschung setzen mehrheitlich auf die High Performance Liquid Chromatography (HPLC) als die Trennmethode ihrer Wahl. Für viele Anwendungen in der Pharmazie, in der Umweltanalytik, der Lebensmittelanalytik, aber auch in der Inprozesskontrolle gibt es mit der Dünnschichtchromatografie eine Alternative.
Im Eurocode 3 wird im Gegensatz zu DIN 18800 die Bemessung von Verbindungen nicht in der Grundnorm DIN EN 1993‐1‐1, sondern in anderen Normenteilen geregelt. Dieser Beitrag behandelt die Bemessung geschweißter Verbindungen nach DIN EN 1993‐1‐8, die auch Hohlprofile, aber weder dünnwandige Bauteile noch Stähle höherer Festigkeit als S460 einschließt, vergleicht diese Bemessung mit der nach DIN 18800‐1, erläutert sie an Beispielen und hebt die wesentlichen Änderungen hervor. Da diese Änderungen auch die im Vergleich zu DIN 18800 viel stärkere Verknüpfung der in der Tragwerksplanung ansetzbaren Beanspruchbarkeiten mit dem Aufwand der Prüfung und Qualitätsüberwachung bei der Herstellung betreffen, werden abschließend wichtige Regelungen der DIN EN 1090‐2 zur Ausführung und Prüfung von Schweißnähten beschrieben, die auch der Tragwerksplaner kennen muss.
Ziel und Tempo der Energiewende sind gesetzt. Der Ausstieg aus der Stromproduktion in Kernkraftwerken soll bis 2022 geschafft sein. Eine Elektrizitätserzeugung, die auf erneuerbaren Energien beruht, soll die bisherige Erzeugung auf der Grundlage von Kohle, Kernbrennstoffen und Erdgas bis 2050 stufenweise weitgehend ablösen und damit maßgeblich zu den Klimaschutzzielen der Bundesregierung beitragen. Der Weg zu diesen Zielen ist für die Beteiligten hingegen noch nicht deutlich einsehbar. Viele offene Fragestellungen technischer, ökonomischer, legislativer und gesellschaftlicher Natur verstellen den Blick auf eine klare Strategie zur Erreichung der energiepolitischen Ziele. Vielschichtige Aufgaben und immense Herausforderungen kommen mit der Mammutaufgabe „Energiewende“ auf Politik, Wirtschaft, Wissenschaft und Bevölkerung zu. Ein wichtiger Enabler für die erfolgreiche Integration von Wind- und Sonnenenergie sowie für neue Prozesse, Marktrollen und Technologien ist die Informations- und Kommunikationstechnologie (IKT). An diesem Punkt setzt die hier vorliegende Studie an.
Power systems are increasingly built from distributed generation units and smart consumers that are able to react to grid conditions. Managing this large number of decentralized electricity sources and flexible loads represent a very huge optimization problem. Both from the regulatory and the computational perspective, no one central coordinator can optimize this overall system. Decentralized control mechanisms can, however, distribute the optimization task through price signals or market-based mechanisms. This chapter presents the concepts that enable a decentralized control of demand and supply while enhancing overall efficiency of the electricity system. It highlights both technological and business challenges that result from the realization of these concepts, and presents the state-of-the-art in the respective domains.