Refine
Year of publication
Document Type
- Article (reviewed) (35)
- Conference Proceeding (26)
- Patent (4)
- Article (unreviewed) (4)
- Report (4)
- Book (1)
- Part of a Book (1)
Conference Type
- Konferenz-Abstract (18)
- Konferenzartikel (7)
- Sonstiges (1)
Has Fulltext
- no (75) (remove)
Is part of the Bibliography
- yes (75) (remove)
Keywords
- Lithiumbatterie (10)
- Brennstoffzelle (7)
- Batterie (5)
- Elektrochemie (4)
- Lithium-Ionen-Akkumulator (4)
- Hochtemperaturbrennstoffzelle (3)
- Durchfluss (2)
- Elektrode (2)
- Elektrolyt (2)
- Festoxidbrennstoffzelle (2)
Institute
Open Access
- Open Access (29)
- Closed Access (27)
- Closed (1)
- Diamond (1)
A two-dimensional single-phase model is developed for the steady-state and transient analysis of polymer electrolyte membrane fuel cells (PEMFC). Based on diluted and concentrated solution theories, viscous flow is introduced into a phenomenological multi-component modeling framework in the membrane. Characteristic variables related to the water uptake are discussed. A Butler–Volmer formulation of the current-overpotential relationship is developed based on an elementary mechanism of electrochemical oxygen reduction. Validated by using published V–I experiments, the model is then used to analyze the effects of operating conditions on current output and water management, especially net water transport coefficient along the channel. For a power PEMFC, the long-channel configuration is helpful for internal humidification and anode water removal, operating in counterflow mode with proper gas flow rate and humidity. In time domain, a typical transient process with closed anode is also investigated.
The state-of-the-art electrochemical impedance spectroscopy (EIS) calculations have not yet started from fully multi-dimensional modeling. For a polymer electrolyte membrane fuel cell (PEMFC) with long flow channel, the impedance plot shows a multi-arc characteristic and some impedance arcs could merge. By using a step excitation/Fourier transform algorithm, an EIS simulation is implemented for the first time based on the full 2D PEMFC model presented in the first part of this work. All the dominant transient behaviors are able to be captured. A novel methodology called ‘configuration of system dynamics’, which is suitable for any electrochemical system, is then developed to resolve the physical meaning of the impedance spectra. In addition to the high-frequency arc due to charge transfer, the Nyquist plots contain additional medium/low-frequency arcs due to mass transfer in the diffusion layers and along the channel, as well as a low-frequency arc resulting from water transport in the membrane. In some case, the impedance spectra appear partly inductive due to water transport, which demonstrates the complexity of the water management of PEMFCs and the necessity of physics-based calculations.
Ziel der Investitionsmaßnahme Enerlab 4.0 war die Bereitstellung einer umfangreichen in-operando und post-mortem Diagnostik für dezentrale Energieerzeuger und -Speicher, z. B. Batteriezellen und Photovoltaikzellen. Diese sind wichtige Komponenten für verschiedene Bereiche der Industrie 4.0 – von autonomen Sensoren über energieautarke Produktion bis hin zur Qualitätskontrolle. Zu diesem Zweck wurde die apparative Ausstattung der Hochschule Offenburg erweitert, und zwar sowohl für in-operando Diagnostik (elektrische Zyklierer, Impedanzspektrometer, Temperaturprüfschränke) als auch für post-mortem Diagnostik (Glovebox, Probenpräparationen für vorhandene Werkstoffanalytik und chemische Analytik). Be-reits vorhandene Geräte aus anderen laufenden oder abgeschlossenen Projekten wurden in die neue Infrastruktur integriert. Im Ergebnis entstand ein modernes und leistungsfähiges Batterie- und Photovoltaiklabor, welches in zahlreichen laufenden und neuen Vorhaben genutzt wird.
Die Erfindung betrifft ein Verfahren und eine Vorrichtung zur Bestimmung des Ladezustandes (SOC) einer aufladbaren Batterie (106) eines vorgegebenen Batterietyps oder eines damit in einem physikalischen Zusammenhang stehenden Parameters, insbesondere einer in der Batterie enthaltenen Restladungsmenge Q, wobei das Verfahren mittels eines spannungsgeführten Batteriemodells (102) arbeitet, welches für die betreffende Batterie (106) oder einen entsprechenden Batterietyp parametriert wird. Es muss lediglich die Batteriespannung Umess gemessen und dem Batteriemodell (102) als Eingangsgröße zur Verfügung gestellt werden. Weiterhin betrifft die Erfindung ein Verfahren und eine Vorrichtung zur Bestimmung des Gesundheitszustandes (SOH) einer Batterie (102), wobei das Batteriemodell (102), das auch zur Bestimmung des SOC verwendet wird, einen modellierten Batteriestrom Imodliefert. Aus diesem können modellierte Ladungsmengen während Lade- und Entladephasen der Batterie (106) bestimmt und mit gemessenen Ladungsmengen, die aus dem gemessenen Batteriestrom Imessbestimmt werden, verglichen werden. Da das Batteriemodell (102) nicht altert, kann hierdurch der SOH der Batterie bestimmt werden.
Die Erfindung betrifft ein Verfahren und eine Vorrichtung zur Bestimmung des Ladezustandes (SOC) einer aufladbaren Batterie (106) eines vorgegebenen Batterietyps oder eines damit in einem physikalischen Zusammenhang stehenden Parameters, insbesondere einer in der Batterie enthaltenen Restladungsmenge Q, wobei das Verfahren mittels eines spannungsgeführten Batteriemodells (102) arbeitet, welches für die betreffende Batterie (106) oder einen entsprechenden Batterietyp parametriert wird. Es muss lediglich die Batteriespannung Umess gemessen und dem Batteriemodell (102) als Eingangsgröße zur Verfügung gestellt werden. Weiterhin betrifft die Erfindung ein Verfahren und eine Vorrichtung zur Bestimmung des Gesundheitszustandes (SOH) einer Batterie (102), wobei das Batteriemodell (102), das auch zur Bestimmung des SOC verwendet wird, einen modellierten Batteriestrom Imodliefert. Aus diesem können modellierte Ladungsmengen während Lade- und Entladephasen der Batterie (106) bestimmt und mit gemessenen Ladungsmengen, die aus dem gemessenen Batteriestrom Imessbestimmt werden, verglichen werden. Da das Batteriemodell (102) nicht altert, kann hierdurch der SOH der Batterie bestimmt werden.
The invention relates to a method and to a device for determining the state of charge (SOC) of a rechargeable battery (106) of a specified battery type or a parameter physically related thereto, in particular a remaining charge amount Q contained in the battery, the method operating by means of a voltage-controlled battery model (102), which is parameterized for the battery (106) in question or a corresponding battery type. It is merely necessary to measure the battery voltage Umess and to provide said battery voltage to the battery model (102) as an input variable. The invention further relates to a method and to a device for determining the state of health (SOH) of a battery (102), wherein the battery model (102) also used to determine the SOC provides a modeled battery current Imod. Modeled charge amounts during charging and discharging phases of the battery (106) can be determined from said modeled battery current and can be compared with measured charge amounts, which are determined from the measured battery current Imess. Because the battery model (102) does not age, the SOH of the battery can thereby be determined.
Ziel des Projekts STABIL war die Vorhersage der Alterung und Verbesserung der Lebensdauer von mobilen und stationären Lithium-Ionen-Batterien. Batterien sind zentrale Komponenten der Elektromobilität und der stationären Speicherung von regenerativem Strom. Die im Stand der Technik unzureichende Lebensdauer der Batterie ist heute wesentlicher Kostentreiber. Im Projekt wurde daher in einem skalenübergreifenden und interdisziplinären Ansatz das Verhalten von einzelnen Batteriezellen und ganzen Batteriesystemen unter zwei unterschiedlichen systemischen Randbedingungen untersucht.
Ziel des LiBaLu-Teilprojekts Modellierung und Simulation war die Unterstützung der Elektroden- und Zellentwicklung mit Hilfe umfangreicher Computersimulationen im Sinne des computergestützten Engineering (CAE). Zwei verschiedene Schwerpunkte standen im Mittelpunkt der Untersuchungen. Zum einen wurde das mechanistische Verständnis der komplexen Elektrochemie in Lithium-Luftbatterien durch mikrokinetische Modelle aufgeklärt. Auf Basis von postulierten Mehrschrittmechanismen wurden makroskopische Eigenschaften (Entlade-/Ladekennlinien, Zyklovoltammogramme) vorhergesagt und mit experimentellen Daten der Projektpartner verglichen. Zum anderen wurde das Design der Prototypzelle mit Hilfe numerischer Simulationen untersucht und optimiert. So konnten z. B. optimale Schichtdicken oder die Rolle von Gastransportlimitierungen identifiziert werden.
Passive hybridization refers to a parallel connection of photovoltaic and battery cells on the direct current level without any active controllers or inverters. We present the first study of a lithium-ion battery cell connected in parallel to a string of four or five serially-connected photovoltaic cells. Experimental investigations were performed using a modified commercial photovoltaic module and a lithium titanate battery pouch cell, representing an overall 41.7 W-peak (photovoltaic)/36.8 W-hour (battery) passive hybrid system. Systematic and detailed monitoring of this system over periods of several days with different load scenarios was carried out. A scaled dynamic synthetic load representing a typical profile of a single-family house was successfully supplied with 100 % self-sufficiency over a period of two days. The system shows dynamic, fully passive self-regulation without maximum power point tracking and without battery management system. The feasibility of a photovoltaic/lithium-ion battery passive hybrid system could therefore be demonstrated.
Die Erfindung betrifft eine Photovoltaik-Stromversorgungsvorrichtung, insbesondere vom öffentlichen Stromnetz unabhängige Photovoltaik-Stromversorgungsvorrichtung, mit einem positiven (204) und einem negativen (206) Lastanschluss für den Anschluss einer elektrischen Last, mit einer Mehrzahl von photovoltaischen Zellen (104) und einer wiederaufladbaren Batterie (5), welche wenigstens zwei in Serie geschaltete Batteriezellen (112) umfasst. Nach der Erfindung sind die photovoltaischen Zellen (104) zu einer der Anzahl der Batteriezellen (112) entsprechenden Anzahl von seriell verbundenen Teilstrings (108) verschaltet und jeder Teilstring (108) ist mit einem positiven Teilstringanschluss mit einem Pluspol und mit einem negativen Teilstringanschluss mit einem Minuspol einer zugeordneten Batteriezelle (112) oder mehreren zugeordneten parallel geschalteten Batteriezellen (112) verbunden. Dabei kann jeder Teilstring (108) zwischen dem positiven und negativen Teilstringanschluss eine maximale Leerlaufspannung erzeugen, die kleiner oder gleich einer vorgegebenen Ladeschlussspannung der zugeordneten Batteriezelle (112) oder der zugeordneten parallel geschalteten Batteriezellen (112) ist. Weiterhin betrifft die Erfindung eine Schaltungsanordnung zum Laden einer wiederaufladbaren Batterie, die zur Realisierung einer derartigen Photovoltaik-Stromversorgungsvorrichtung geeignet ist.
Simulation-based degradation assessment of lithium-ion batteries in a hybrid electric vehicle
(2017)
The accurate diagnosis of state of charge (SOC) and state of health (SOH) is of utmost importance for battery users and for battery manufacturers. State diagnosis is commonly based on measuring battery current and using it in Coulomb counters or as input for a current-controlled model. Here we introduce a new algorithm based on measuring battery voltage and using it as input for a voltage-controlled model. We demonstrate the algorithm using fresh and pre-aged lithium-ion battery single cells operated under well-defined laboratory conditions on full cycles, shallow cycles, and a dynamic battery electric vehicle load profile. We show that both SOC and SOH are accurately estimated using a simple equivalent circuit model. The new algorithm is self-calibrating, is robust with respect to cell aging, allows to estimate SOH from arbitrary load profiles, and is numerically simpler than state-of-the-art model-based methods.
Aqueous lithium–oxygen batteries are promising candidates for electric energy storage. In this paper we present and discuss a multiphase continuum model of an aqueous lithium–oxygen single cell including reactions and transport in a porous gas diffusion electrode (GDE). The model is parameterized using in-house half-cell experiments and available literature data on aqueous electrolytes. We validate our transport model with cyclic voltammetry and electrochemical impedance spectroscopy measurements over a wide range of temperatures (25, 40, 55 °C) and electrolyte concentrations (0.1–2 M). We observe very good agreement between simulations and measurements during oxygen reduction conditions. A sensitivity analysis of the validated model demonstrates the influence of the porous structure on GDE performance and gives directions for the future development of electrodes.
On the Fundamental and Practical Aspects of Modeling Complex Electrochemical Kinetics and Transport
(2018)
Numerous technologies, such as batteries and fuel cells, depend on electrochemical kinetics. In some cases, the responsible electrochemistry and charged-species transport is complex. However, to date, there are essentially no general-purpose modeling capabilities that facilitate the incorporation of thermodynamic, kinetic, and transport complexities into the simulation of electrochemical processes. A vast majority of the modeling literature uses only a few (often only one) global charge-transfer reactions, with the rates expressed using Butler–Volmer approximations. The objective of the present paper is to identify common aspects of electrochemistry, seeking a foundational basis for designing and implementing software with general applicability across a wide range of materials sets and applications. The development of new technologies should be accelerated and improved by enabling the incorporation of electrochemical complexity (e.g., multi-step, elementary charge-transfer reactions and as well as supporting ionic and electronic transport) into the analysis and interpretation of scientific results. The spirit of the approach is analogous to the role that Chemkin has played in homogeneous chemistry modeling, especially combustion. The Cantera software, which already has some electrochemistry capabilities, forms the foundation for future capabilities expansion.
Lithium-oxygen cells with organic electrolyte suffer high overpotentials during charge, indicating asymmetric charge/discharge reaction mechanisms. We present a multi-physics dynamic modeling and simulation study of the Li/O2 cell cycling behavior. We present three different multi-step mechanisms of the 2 Li + O2 ⇄ Li2O2 cell reaction, (A) a reversible 5-step mechanism, (B) a partially irreversible 6-step mechanism, and (C) a partially irreversible 8-step mechanism that includes reactions of a redox mediator. Model predictions are compared to experimental galvanostatic cycling data of Swagelok cells without and with 2,2,6,6-tetramethylpiperidinyloxyl (TEMPO) as redox mediator. All mechanisms are able to predict the discharge behavior in good agreement to the experimental results. The experimentally observed high charge overpotentials as well as their reduction by using a redox mediator can be qualitatively reproduced with the irreversible reaction mechanisms. However, the particular shape of the experimental charge curve with continuously increasing charge overpotential cannot be reproduced with the present mechanisms.
Lithium–oxygen cells with nonaqueous electrolyte show high overpotentials during charge, indicating asymmetric charge/discharge reaction mechanisms. We present a kinetic modeling and simulation study of the lithium–oxygen cell cycling behavior. The model includes a multistep reaction mechanism of the cell reaction (2Li + O2 ⇄ Li2O2) forming lithium peroxide by precipitation, coupled to a 1D porous-electrode transport model. We apply the model to study the asymmetric discharge/charge characteristics and analyze the influence of a redox mediator dissolved homogeneously in the liquid electrolyte. Model predictions are compared to experimental galvanostatic cycling data of cells without and with 2,2,6,6-tetramethylpiperidinyloxyl (TEMPO) as redox mediator. The predicted discharge behavior shows good agreement with the experimental results. A spatiotemporal analysis of species concentrations reveals inhomogeneous distributions of dissolved oxygen and reaction products within the cathode during discharge. The experimentally observed charge overpotentials as well as their reduction by using a redox mediator can be qualitatively reproduced with a partially irreversible reaction mechanism. However, the proposed models fail to reproduce the particular shape of the experimental charge curve with continuously increasing charge overpotential, which implies that part of the reaction mechanism is still open for investigation in future work.
Seven cell design concepts for aqueous (alkaline) lithium–oxygen batteries are investigated using a multi-physics continuum model for predicting cell behavior and performance in terms of the specific energy and specific power. Two different silver-based cathode designs (a gas diffusion electrode and a flooded cathode) and three different separator designs (a porous separator, a stirred separator chamber, and a redox-flow separator) are compared. Cathode and separator thicknesses are varied over a wide range (50 μm–20 mm) in order to identify optimum configurations. All designs show a considerable capacity-rate effect due to spatiotemporally inhomogeneous precipitation of solid discharge product LiOH·H2O. In addition, a cell design with flooded cathode and redox-flow separator including oxygen uptake within the external tank is suggested. For this design, the model predicts specific power up to 33 W/kg and specific energy up to 570 Wh/kg (gravimetric values of discharged cell including all cell components and catholyte except housing and piping).
Electrochemical impedance spectroscopy (EIS) is a widely-used diagnostic technique to characterize electrochemical processes. It is based on the dynamic analysis of two electrical observables, that is, current and voltage. Electrochemical cells with gaseous reactants or products (e.g., fuel cells, metal/air cells, electrolyzers) offer an additional observable, that is, the gas pressure. The dynamic coupling of current and/or voltage with gas pressure gives rise to a number of additional impedance definitions, for which we have introduced the term electrochemical pressure impedance spectroscopy (EPIS) [1,2]. EPIS shows a particular sensitivity towards transport processes of gas-phase or dissolved species, in particular, diffusion coefficients and transport pathway lengths. It is as such complementary to standard EIS, which is mainly sensitive towards electrochemical processes. This sensitivity can be exploited for model parameterization and validation. A general analysis of EPIS is presented, which shows the necessity of model-based interpretation of the complex EPIS shapes in the Nyquist plot (cf. Figure). We then present EPIS simulations for two different electrochemical cells: (1) a sodium/oxygen battery cell and (2) a hydrogen/air fuel cell. We use 1D or 2D electrochemical and transport models to simulate current excitation/pressure detection or pressure excitation/voltage detection. The results are compared to first EPIS experimental data available in literature [2,3].
Electrochemical impedance spectroscopy (EIS) is a widely-used diagnostic technique to characterize electrochemical processes. It is based on the dynamic analysis of two electrical observables, that is, current and voltage. Electrochemical cells with gaseous reactants or products (e.g., fuel cells, metal/air cells, electrolyzers) offer an additional observable, that is, the gas pressure. The dynamic coupling of current and/or voltage with gas pressure gives rise to a number of additional impedance definitions, for which we use the term electrochemical pressure impedance. It also gives rise to different experimental probing approaches. In this article we present a model-based study of electrochemical pressure impedance spectroscopy (EPIS). Possible quantifications and realizations of EPIS are discussed. The study of generic cell geometries consisting of gas reservoir, diffusion layer(s) and electrochemically active layer(s) reveals distinct spiral-shaped features in the Nyquist plot. Using the example of a sodium/oxygen (Na/O2) cell, the dynamic spatiotemporal behavior of the state variables is quantified and interpreted. Results are compared to first experimental EPIS measurements by Hartmann et al. [J. Phys. Chem. C118, 1461, 2014]. A sensitivity analysis highlights the properties of EPIS with respect to geometric, transport, and kinetic parameters. We demonstrate that EPIS is sensitive to transport parameters that are not well-accessible with standard EIS.
Lithium-ion pouch cells with lithium titanate (Li4Ti5O12, LTO) anode and lithium nickel cobalt aluminum oxide (LiNi0.8Co0.15Al0.05O2, NCA) cathode were investigated experimentally with respect to their electrical (0.1C…4C), thermal (5 °C…50 °C) and long-time cycling behavior. The 16 Ah cell exhibits an asymmetric charge/discharge behavior which leads to a strong capacity-rate effect, as well as a significantly temperature-dependent capacity (0.37 Ah ∙ K−1) which expresses as additional high-temperature feature in the differential voltage plot. The cell was cycled for 10,000 cycles inbetween the nominal voltage limits (1.7–2.7 V) with a symmetric 4C constant-current charge/discharge protocol, corresponding to approx. 3400 equivalent full cycles. A small (0.192 mΩ/1000 cycles) but continuous increase of internal resistance was observed. Using electrochemical impedance spectroscopy (EIS), this could be identified to be caused by the NCA cathode, while the LTO anode showed only minor changes during cycling. The temperature-corrected capacity during 4C cycling exhibited a decrease of 1.28%/1000 cycles. The 1C discharge capacity faded by only 4.0% for CC discharge and 2.3% for CCCV discharge after 10,000 cycles. The cell thus exhibits very good internal-resistance stability and excellent capacity retention even under harsh (4C continuous) cycling, demonstrating the excellent stability of LTO as anode material.
Nickel cobalt aluminum oxide (NCA) based lithium-ion battery electrodes exhibit a distinct asymmetry in discharge/charge behavior towards high bulk stoichiometry (low state of charge). We show that basic electrochemical relationships, that is, the Nernst equation and the Butler-Volmer equation, are able to reproduce this behavior when a two-step reaction mechanism is assumed. The two-step mechanism consists of (1) lithium-ion adsorption from the electrolyte onto the active material particle surface under electron transfer, and (2) intercalation of surface-adsorbed lithium atoms into the bulk material. The asymmetry of experimental half-cell data of an NCA electrode cycled at 0.1 C-rate can be quantitatively reproduced with this simple model. The model parameters show two alternative solutions, predicting either a saturated (highly-covered) or a depleted surface for high bulk lithiation.
Pressure dynamics in metal-oxygen (metal-air) batteries: a case study on sodium superoxide cells
(2014)
Electrochemical reactions in metal–oxygen batteries come along with the consumption or release of gaseous oxygen. We present a novel methodology for investigating electrode reactions and transport phenomena in metal–oxygen batteries by measuring the pressure dynamics in an enclosed gas reservoir above the oxygen electrode. The methodology is exemplified by a room-temperature sodium–oxygen battery forming sodium superoxide (NaO2) in an electrolyte of diethylene glycol dimethyl ether (diglyme) and sodium trifluoromethanesulfonate (NaOSO2CF3, NaOTf). The experiments are supported by microkinetic simulations with a one-dimensional multiphysics continuum model. During galvanostatic cycling over 30 cycles, a constant oxygen consumption/release rate is observed upon discharge/charge. The number of transferred electrons per oxygen molecule is calculated to 1.01 ± 0.02 and 1.03 ± 0.02 for discharge and charge, respectively, confirming the nature of the oxygen reaction product as superoxide O2–. The same ratio is observed in cyclic voltammetry experiments with low scan rate (<1 mV/s). However, at higher scan rates, the ratio increases as a result of oxygen transport limitations in the electrolyte. We introduce electrochemical pressure impedance spectroscopy (EPIS) for simultaneously analyzing current, voltage, and pressure of electrochemical cells. Pressure recording significantly increases the sensitivity of impedance toward oxygen transport properties of the porous electrode systems. In addition, we report experimental data on the diffusion coefficient and solubility of oxygen in electrolyte solutions as important parameters for the microkinetic models.
Lithium–sulfur (Li/S) cells are promising candidates for a next generation of safe and cost-effective high energy density batteries for mobile and stationary applications. At present, most Li/S cells still suffer from relatively poor cyclability, capacity loss under moderate current densities and self-discharge. Furthermore, the underlying chemical mechanisms of the general discharge/charge behavior as well as Li/S-specific phenomena like the polysulfide shuttle are not yet fully understood. Here we present a thermodynamically consistent, fully reversible continuum model of a Li/S cell with simplified four-step electrochemistry, including a simple description of the polysulfide shuttle effect. The model is parameterized using experimental discharge curves obtained from literature and reproduces behavior at various current densities with fairly high accuracy. While being instructively simple, the presented model can still reproduce distinct macroscopic Li/S-cell features caused by the shuttle effect, e.g., seemingly infinite charging at low charge current densities, and suboptimal coulombic efficiency. The irreversible transport of active material from the cathode to the anode results in a voltage drop and capacity loss during cycling, which can also be observed experimentally.
In this paper we present a model of the discharge of a lithium–oxygen battery with aqueous electrolyte. Lithium–oxygen batteries (Li–O2) have recently received great attention due to their large theoretical specific energy. Advantages of the aqueous design include the stability of the electrolyte, the long experience with gas diffusion electrodes (GDEs), and the solubility of the reaction product lithium hydroxide. However, competitive specific energies can only be obtained if the product is allowed to precipitate. Here we present a dynamic one-dimensional model of a Li–O2 battery including a GDE and precipitation of lithium hydroxide. The model is parameterized using experimental data from the literature. We demonstrate that GDEs remove power limitations due to slow oxygen transport in solutions and that lithium hydroxide tends to precipitate on the anode side. We discuss the system architecture to engineer where nucleation and growth predominantly occurs and to optimize for discharge capacity.
Compact solid discharge products enable energy storage devices with high gravimetric and volumetric energy densities, but solid deposits on active surfaces can disturb charge transport and induce mechanical stress. In this Letter, we develop a nanoscale continuum model for the growth of Li2O2 crystals in lithium–oxygen batteries with organic electrolytes, based on a theory of electrochemical nonequilibrium thermodynamics originally applied to Li-ion batteries. As in the case of lithium insertion in phase-separating LiFePO4 nanoparticles, the theory predicts a transition from complex to uniform morphologies of Li2O2 with increasing current. Discrete particle growth at low discharge rates becomes suppressed at high rates, resulting in a film of electronically insulating Li2O2 that limits cell performance. We predict that the transition between these surface growth modes occurs at current densities close to the exchange current density of the cathode reaction, consistent with experimental observations.
Proton Exchange Membrane Fuel Cells (PEMFC) are energy efficient and environmentally friendly alternatives to conventional energy conversion systems in many yet emerging applications. In order to enable prediction of their performance and durability, it is crucial to gain a deeper understanding of the relevant operation phenomena, e.g., electrochemistry, transport phenomena, thermodynamics as well as the mechanisms leading to the degradation of cell components. Achieving the goal of providing predictive tools to model PEMFC performance, durability and degradation is a challenging task requiring the development of detailed and realistic models reaching from the atomic/molecular scale over the meso scale of structures and materials up to components, stack and system level. In addition an appropriate way of coupling the different scales is required.
This review provides a comprehensive overview of the state of the art in modeling of PEMFC, covering all relevant scales from atomistic up to system level as well as the coupling between these scales. Furthermore, it focuses on the modeling of PEMFC degradation mechanisms and on the coupling between performance and degradation models.
The DMFC is a promising option for backup power systems and for the power supply of portable devices. However, from the modeling point of view liquid-feed DMFC are challenging systems due to the complex electrochemistry, the inherent two-phase transport and the effect of methanol crossover. In this paper we present a physical 1D cell model to describe the relevant processes for DMFC performance ranging from electrochemistry on the surface of the catalyst up to transport on the cell level. A two-phase flow model is implemented describing the transport in gas diffusion layer and catalyst layer at the anode side. Electrochemistry is described by elementary steps for the reactions occurring at anode and cathode, including adsorbed intermediate species on the platinum and ruthenium surfaces. Furthermore, a detailed membrane model including methanol crossover is employed. The model is validated using polarization curves, methanol crossover measurements and impedance spectra. It permits to analyze both steady-state and transient behavior with a high level of predictive capabilities. Steady-state simulations are used to investigate the open circuit voltage as well as the overpotentials of anode, cathode and electrolyte. Finally, the transient behavior after current interruption is studied in detail.
Passive hybridization of battery cell and photovoltaic cell: modeling and experimental validation
(2017)
Modelling detailed chemistry in lithium-ion batteries: Insight into performance, ageing and safety
(2018)
Muli-scale thermos-electrochemical modelling of aging mechanisms in an LFP/graphite lithium-ion cell
(2017)
In this article the high-temperature behavior of a cylindrical lithium iron phosphate/graphite lithium-ion cell is investigated numerically and experimentally by means of differential scanning calorimetry (DSC), accelerating rate calorimetry (ARC), and external short circuit test (ESC). For the simulations a multi-physics multi-scale (1D+1D+1D) model is used. Assuming a two-step electro-/thermochemical SEI formation mechanism, the model is able to qualitatively reproduce experimental data at temperatures up to approx. 200 °C. Model assumptions and parameters could be evaluated via comparison to experimental results, where the three types of experiments (DSC, ARC, ESC) show complementary sensitivities towards model parameters. The results underline that elevated-temperature experiments can be used to identify parameters of the multi-physics model, which then can be used to understand and interpret high-temperature behavior. The resulting model is able to describe nominal charge/discharge operation behavior, long-term calendaric aging behavior, and short-term high-temperature behavior during extreme events, demonstrating the descriptive and predictive capabilities of physicochemical models.
n this work a mathematical model for describing the performance of lithium-ion battery electrodes consisting of porous active material particles is presented. The model represents an extension of the Newman-type model, accounting for the agglomerate structure of the active material particles, here Li(Ni1/3Co1/3Mn1/3)O2 (NCM) and Li(Ni1/3Co1/3Al1/3)O2 (NCA). To this goal, an additional pore space is introduced on the active material level. The space is filled with electrolyte and a charge-transfer reaction takes place at the liquid-solid interface within the porous active material particles. Volume-averaging techniques are used to derive the model equations. A local Thiele modulus is defined and provides an insight into the potentially limiting factors on the active material level. The introduction of a liquid-phase ion transport within the active material reduces the overall transport losses, while the additional active surface area within the agglomerate lowers the charge-transfer resistance. As a consequence, calculated discharge capacities are higher for particles modeled as agglomerates. This finding is more pronounced in the case of high C-rates
Modeling and simulation play a key role in analyzing the complex electrochemical behavior of lithium-ion batteries. We present the development of a thermodynamic and kinetic modeling framework for intercalation electrochemistry within the open-source software Cantera. Instead of using equilibrium potentials and single-step Butler-Volmer kinetics, Cantera is based on molar thermodynamic data and mass-action kinetics, providing a physically-based and flexible means for complex reaction pathways. Herein, we introduce a new thermodynamic class for intercalation materials into the open-source software. We discuss the derivation of molar thermodynamic data from experimental half-cell potentials, and provide practical guidelines. We then demonstrate the new class using a single-particle model of a lithium cobalt oxide/graphite lithium-ion cell, implemented in MATLAB. With the present extensions, Cantera provides a platform for the lithium-ion battery modeling community both for consistent thermodynamic and kinetic models and for exchanging the required thermodynamic and kinetic parameters. We provide the full MATLAB code and parameter files as supplementary material to this article.
One of the bottlenecks hindering the usage of polymer electrolyte membrane fuel cell technology in automotive applications is the highly load-sensitive degradation of the cell components. The cell failure cases reported in the literature show localized cell component degradation, mainly caused by flow-field dependent non-uniform distribution of reactants. The existing methodologies for diagnostics of localized cell failure are either invasive or require sophisticated and expensive apparatus. In this study, with the help of a multiscale simulation framework, a single polymer electrolyte membrane fuel cell (PEMFC) model is exposed to a standardized drive cycle provided by a system model of a fuel cell car. A 2D multiphysics model of the PEMFC is used to investigate catalyst degradation due to spatio-temporal variations in the fuel cell state variables under the highly transient load cycles. A three-step (extraction, oxidation, and dissolution) model of platinum loss in the cathode catalyst layer is used to investigate the cell performance degradation due to the consequent reduction in the electro-chemical active surface area (ECSA). By using a time-upscaling methodology, we present a comparative prediction of cell end-of-life (EOL) under different driving behavior of New European Driving Cycle (NEDC) and Worldwide Harmonized Light Vehicles Test Cycle (WLTC).
Practical bottlenecks associated with commercialization of Lithium-air cells include capacity limitation and low cycling efficiency. The origin of such losses can be traced to complex electrochemical side reactions and reactant mass transport losses[1]. The efforts to minimize such losses include exploration of various electrolytes with additives[2], and cell component geometry and material design. Given the wide range of options for such materials, it is almost impractical to experimentally setup and characterize all those cells. Consequently, modeling and simulation studies are efficient alternatives to analyze spatially and temporally resolved cell behavior for various combinations of materials[3]. In this study, with the help of a two-dimensional multi physics model, we have focused on the effect of electrode and electrolyte interaction (electrochemistry), choice of electrolyte (species transport), and electrode geometry (electrode design) on the performance of a lithium-air button cell. Figure1a shows the schematics of the 2D axisymmetric computational domain. A comparative analysis of five different electrolytes was performed while focusing on the 2D distribution of local current density and the concentration of electro-chemically active species in the cell, that is, O2and Li+. Using two different cathode configurations, namely, flooded electrode and gas diffusion electrode (GDE)[4] at different cathode thickness, the effect of cell geometry and electrolyte saturation on cell performance was explored. Further, a detailed discussion on electrode volume utilization (cf. Figure1b) is presented via changes in the active volume of cathode that produces 90% of the total current with the cell current density for different combinations of electrolyte saturations and cathode thickness.