Refine
Year of publication
- 2009 (9) (remove)
Document Type
- Conference Proceeding (9) (remove)
Conference Type
- Konferenzartikel (7)
- Sonstiges (2)
Has Fulltext
- no (9)
Is part of the Bibliography
- yes (9) (remove)
Institute
Open Access
- Closed Access (9) (remove)
Non-Esterified Plant Oils as Fuel -Engine Characteristics, Emissions and Mutagenic effects of PM-
(2009)
Plant oils may be used as a sustainable, nearly CO2 neutral fuel for diesel engines. This work investigates experimentally the particulate and gaseous emissions of diesel engines fuelled with non-esterified, pure plant oils with the quality standard of DIN V 51605 (Weihen-stephan RK-Qualitätsstandard 05/2000). The data are collected from three engines:
Common rail passenger car engine from OPEL AG
Truck engine from VOLVO
Truck engine from MAN AG
All engines have been correctly adjusted to plant oil operation.
The OPEL and VOLVO engines served for the basic investigations. The emissions of the MAN engine have been used to perform AMES tests to analyze possible health impacts of plant oil operation.
The experimental data show a reduction of particulate matter compared to traditional gasoil which may yield up to 50 % for. The particulate matter shows same primary particle sizes but the agglomerates as collected on TEM grids are different - the plant oil soot particles tend to form larger aggregates [4]. The gaseous emissions of CO and hydrocarbons HC are generally lower compared to the operation with gasoil. However, the NOX emissions are slightly higher. This may be contributed to the measured higher combustion chamber pressures and temperatures when fuelled by plant oils.
Emission samples have been extracted from ESC cycles of 13 step tests to perform the AMES test which give indication on carcinogen substances. The AMES test results gave no indication of mutagenic effects exceeding the detection limits. No significant differences could be found comparing the emissions of plant oil and gasoil operation. Thus, it can be stated that the emission from plant oil operation does not have a health impact different to traditional gas oil. This is in contrast to some other publications — a deeper insight shows that these investigations did not properly modify the engine for plant oils. It is mandatory to make the engine modification to pre-warm the plant oils to approx. 90°C prior to injection. The engine's warm-up phase needs special care to avoid any coking at the injection system and combustion chamber surfaces. The publications where a higher health risk was claimed to be found in the exhaust of plant oil fuels, did not pre-warm the plant oils — cold plant oils have been injected in the combustion chamber instead. This results in incomplete atomization and incomplete combustion with a lot of hazardous emission species (see also [4,11]. Such an operation will damage the engine after relatively short times and is, therefore, not realistic.
The investigated fuels had some influence on the engine characteristics. Higher temperatures and pressures in the cylinder have been detected for some plant oils compared to gasoil. This increase is explained by the higher oxygen content within the plant oils.
This paper discusses a technological solution to real-time road transportation optimization using a commercial multi-agent based system, LS/ATN, which has been proven through real-world deployment to reduce transportation costs for both small and large fleets in the full and part load business. Subsequent to describing the real-time optimization approach, we discuss how the platform is currently evolving to accept live data from vehicles in the fleet in order to improve optimization accuracy. A selection of the predominant pervasive technologies available today for enhancing intelligent route optimization is described.
Für die solarunterstützte CO2-neutrale Nahwärmeversorgung des Neubaugebiets Hülben in Holzgerlingen wurden Holzpelletskessel mit einer 249m²-großen Solaranlage kombiniert. Im ersten Intensivmessjahr vom 01.03.2007 bis 29.02.2008 wurde eine Gesamt-Wärmeabgabe ins Nahwärmenetz von 920.606 kWh gemessen, wobei der solare Anteil bei 84.033 kWh lag. Es wurden ein Systemnutzungsgrad von 23,8 % und ein solarer Deckungsanteil von 9,5% gemessen. Die vom Lieferanten abgegebene Energiegarantie wurde in der ersten Intensivmessphase nicht erreicht.
There are additional long-term effects which also change the micro-structure of the polymer network and consequently the effective number of polymer chains in the material. These effects are summarized by ageing processes and will be used in the following to explain the basic assumptions of the model which can be generalized to simulate the viscous behaviour of the material. An implementation of these concepts into FEM codes is straightforward and has been carried out to the solver ABAQUS, Baaser & Ziegler (2006), Baaser et al. (2009).