Refine
Year of publication
- 2022 (21) (remove)
Document Type
- Conference Proceeding (21) (remove)
Conference Type
- Konferenzartikel (10)
- Konferenz-Abstract (8)
- Konferenz-Poster (3)
Has Fulltext
- no (21) (remove)
Is part of the Bibliography
- yes (21)
Keywords
- injury (10)
- biomechanics (5)
- running (5)
- ACL (4)
- sport (3)
- Sustainabilty (2)
- TRIZ (2)
- overuse (2)
- Additive manufacturing (1)
- Chemical engineering (1)
Institute
- Fakultät Maschinenbau und Verfahrenstechnik (M+V) (21) (remove)
Open Access
- Open Access (13)
- Bronze (12)
- Closed (6)
- Closed Access (2)
- Diamond (1)
Sweaty has already participated several times in RoboCup soccer competitions (Adult Size). Now the work is focused on stabilizing the gait. Moreover, we would like to overcome the constraints of a ZMP-algorithm that has a horizontal footplate as precondition for the simplification of the equations. In addition we would like to switch between impedance and position control with a fuzzy-like algorithm that might help to minimize jerks when Sweaty’s feet touch the ground.
Significant improvements in module performance are possible via implementation of multi-wire electrodes. This is economically sound as long as the mechanical yield of the production is maintained. While flat ribbons have a relatively large contact area to exert forces onto the solar cell, wires with round cross section reduce this contact area considerably – in theory to an infinitively thin line. Therefore, the local stresses induced by the electrodes might increase to a point that mechanical production yields suffer unacceptably.
In this paper, we assess this issue by an analytical mechanical model as well as experiments with an encapsulant-free N.I.C.E. test setup. From these, we can derive estimations for the relationship between lay-up accuracy and expected breakage losses. This paves the way for cost-optimized choices of handling equipment in industrial N.I.C.E.-wire production lines.
Micronization of biochar (BC) may ease its application in agriculture. For example, fine biochar powders can be applied as suspensions via drip-irrigation systems or can be used to produce grnulated fertilizers. However, micronization may effect important physical biochar properties like the water holding capacity (WHC) or the porosity.
Weitsprung mit und ohne Unterschenkelprothese – gleiche Sportart, unterschiedliche Disziplinen
(2022)
The majority of anterior cruciate ligament (ACL) injuries in team sports are non-contact injuries, with cutting maneuvers identified as high-risk tasks. Young female handball players have been shown to be at greater risk for ACL injuries than males. One risk factor for ACL injuries is the magnitude of the knee abduction moment (KAM). Cutting technique variables on foot placement, overall approach and knee kinematics have been shown to influence the KAM. Since injury risk is believed to increase with increasing task complexity, the purpose of the study was to test the effect of task complexity on technique variables that influence the KAM in female handball players during fake-and-cut tasks.
Konstrukteure im Maschinenbau stehen häufig vor der Problemstellung, hochfest vorgespannte Schraubenverbindungen und einen durchgehenden Korrosionsschutz zu vereinen. Die einschlägigen Normen und Richtlinien bieten hierzu Stand heute keine ausreichende Hilfestellung. In diesem Beitrag werden an Versuchsblechen ermittelte Setzbeträge von maschinenbautypischen organischen Beschichtungssystemen unter Variation der Belastungshöhe und der Umgebungstemperatur präsentiert und mit in Bauteilversuchen gemessenen Vorspannkraftverlusten vergleichend bewertet.
Due to the Covid-19 pandemic, the RoboCup WorldCup 2021 was held completely remotely. For this competition the Webots simulator (https://cyberbotics.com/) was used, so all teams needed to transfer their robot to the simulation. This paper describes our experiences during this process as well as a genetic learning approach to improve our walk engine to allow a more stable and faster movement in the simulation. Therefore we used a docker setup to scale easily. The resulting movement was one of the outstanding features that finally led to the championship title.
Eco-Feasibility Study and Application of Natural Inventive Principles in Chemical Engineering Design
(2022)
The early stages of the front-end process development are critical for the future success of projects involving new technologies. The application of eco-inventive principles identified in natural systems to the design of chemical processes and equipment allows one to find ways to mitigate or avoid secondary ecological problems such as, for example, higher consumption of raw materials or energy, generation of hazardous waste and pollution of the environment by toxic chemicals. However, before implementing a new technology in a real operational environment, it is necessary to completely investigate its undesirable ecological impact and to evaluate the future viability of this technology. Therefore, the research paper presents a study of ecological feasibility of an innovative process design utilising natural eco-inventive principles and analyses the correlations between applied inventive principles. Such eco-feasibility study can be considered as an important decision gate to determine whether the technology implementation should be moved forward. Furthermore, the study evaluates the practicability of natural inventive principles to the eco-friendly process design and is illustrated with an example of a sustainable technology for nickel extraction from pyrophyllite.
Rising societies’ demands require more sustainable products and technologies. Although numerous methods and tools have been developed in the last decades to support environmental-friendly product and process development, an interdisciplinary knowledge base of eco-innovative examples linked to the eco-innovative problems and solution principles is lacking. The paper proposes an ontology of examples for eco-friendly products and technologies assigned to the Inventive Principles (IPs) of the TRIZ methodology in accordance with the German TRIZ Standard VDI 4521. The examples of sustainable technologies and products build a database for sharing and reusing eco-innovation knowledge. The ontology acts as a tool for systematic solving of specific environmental problems in typical life cycle phases, for different environmental impact categories and engineering domains. Finally, the paper defines a future research agenda in the field of the TRIZ-based systematic eco-innovation.
The purpose of this study was to describe the effects of running speed and slope on metatarsophalangeal (MTP) joint kinematics. 22 male and female runners underwent 3D motion analysis on an instrumented treadmill at three different speeds (2.5 m/s, 3.0 m/s, 3.5 m/s). At each speed, participants ran at seven slope conditions (downhill: -15%, -10%, -5%, level, and uphill: +5%, +10%, +15%). We found a significant main effect (p < 0.001) of running speed and slope on peak MTP dorsiflexion and a running speed by slope interaction effect (p < 0.001) for peak MTP dorsiflexion velocity. These findings highlight the need to consider running intensity and environmental factors like running surface inclination when considering MTP joint mechanics and technological aids to support runners.
Effect of downhill running on biomechanical risk factors associated with iliotibial band syndrome
(2022)
The purpose of this study was to identify the influence of downhill running on biomechanical risk factors for iliotibial band syndrome. We conducted a 3D motion analysis of 22 females and males running on an instrumented treadmill at four different inclinations (0%, -5%, -10%, -15%) at a speed of 3.5 m/s. We found significant differences for biomechanical risk factors associated with iliotibial band syndrome. Peak knee flexion angle at initial ground contact (p < .001), peak knee adduction angle (p = .005), and iliotibial band strain (p < .001) systematically increased with increasing slope. Downhill running increases biomechanical risk factors for iliotibial band syndrome. Our results highlight the need to consider the individual running environment in assessing overuse injury risk in runners.
This study aimed to compare a simplified calculation of the knee abduction moment with the traditional inverse dynamics calculation when athletes perform fake-cut maneuvers with different complexities. In the simplified calculation, we multiply the force vector with its lever arm to the knee, projected onto the local coordinate system of the proximal thigh, hence neglecting the inertial contributions from distal segments. We found very strong ranking consistency using Spearman’s rank correlation coefficient when using the simplified method compared to the traditional calculation. Independent of the tasks, the simplified method resulted in higher moments than the inverse dynamics. This was caused by ignoring the moment caused by segment linear acceleration generating a counteracting moment by about 7%. An alternative to the complex calculations of inverse dynamics can be used to investigate the contributions of the GRF magnitude and its lever arm to the knee.
The purpose of this study was to 1) compare knee joint kinematics and kinetics of fake-and-cut tasks of varying complexity in 51 female handball players and 2) present a case study of one athlete who ruptured her ACL three weeks post data collection. External knee joint moments and knee joint angles in all planes at the instance of the peak external knee abduction moment (KAM) as well as moment and angle time curves were analyzed. Peak KAMs and knee internal rotation moments were substantially higher than published values obtained during simple change-of-direction tasks and, along with flexion angles, differed significantly between the tasks. Introducing a ball reception and a static defender increased joint loads while they partially decreased again when anticipation was lacking. Our results suggest to use game-specific assessments of injury risk while complexity levels do not directly increase knee loading. Extreme values of several risk factors for a post-test injured athlete highlight the need and usefulness of appropriate screenings.
Physik durch Informatik
(2022)
Selbsttests in Lernmanagementsystemen (LMS) ermöglichen es Studierenden, den eigenen Lernfortschritt einzuschätzen. Das didaktische Konzept Physik durch Informatik (PDI) ist charakterisiert durch die Nutzung einer Programmiersprache zur Lösungseingabe bei Mathematik und Physik-Aufgaben. Im Gegensatz zur Lösungseingabe durch Zahlenwerte oder im Antwort-Auswahl-Verfahren erfordert die Implementierung einer Lösung in einer Programmiersprache eine höhere Kompetenzstufe.
For some years now, additive manufacturing (AM) has offered an alternative to conventional manufacturing processes. The strengths of AM are primarily the rapid implementation of ideas into a usable product and the ability to produce geometrically complex shapes. It has also significantly advanced the lightweight design of products made of plastic. So far, the strength of printed components made of polymers is previously very limited.
Recently, new AM processes have become available that allow the embedding of short and also long fibers in polymer matrix. Thus, the manufacturing of components that provide a significant increase in strength becomes possible. In this way, both complex geometries and sophisticated applications can be implemented. This paper therefore investigates how this new technology can be implemented in product development, focusing on sports equipment. An extensive literature research shows that lightweight design plays a decisive role in sports equipment. In addition, the advantages of AM in terms of individualized products and low quantities can be fully exploited.
An example of this approach is the steering system for a seat sled used by paraplegic athletes in the Olympic discipline of Nordic paraskiing. A particular challenge here is the placement and alignment of the long carbon fibers within the polymer matrix and the verification of the strength by means of Finite-Element-Analysis (FEA). In addition, findings from bionics are used to optimize the lightweight design of the steering system. Using this example, it can be shown that the weight of the steering system can be drastically reduced compared to conventional manufacturing. At the same time, a number of parts can be saved through function integration and thus the manufacturing and assembly effort can be reduced significantly.