Refine
Document Type
- Article (reviewed) (24)
- Conference Proceeding (8)
Conference Type
- Konferenzartikel (8)
Language
- English (32)
Has Fulltext
- no (32) (remove)
Is part of the Bibliography
- yes (32)
Keywords
- printed electronics (4)
- Hybrid system (1)
- Physical unclonable function (1)
- copper oxide (1)
- crossbar (1)
- diode modeling (1)
- electrolyte-gated transistors (1)
- fingerprinting (1)
- hybrid systems (1)
- identification (1)
Institute
- Fakultät Elektrotechnik, Medizintechnik und Informatik (EMI) (ab 04/2019) (32) (remove)
Open Access
- Closed Access (22)
- Open Access (6)
- Closed (2)
Printed electronics can benefit from the deployment of electrolytesas gate insulators,which enables a high gate capacitance per unit area (1–10 μFcm−2) due to the formation of electrical double layers (EDLs). Consequently, electrolyte-gated field-effect transistors (EGFETs) attain high-charge carrier densities already in the subvoltage regime, allowing for low-voltage operation of circuits and systems. This article presents a systematic study of lumped terminal capacitances of printed electrolyte-gated transistors under various dc bias conditions. We perform voltage-dependent impedancemeasurements and separate extrinsic components from the lumped terminal capacitance.
The proposed Meyer-like capacitance model, which also accounts for the nonquasi-static (NQS) effect, agrees well with experimental data. Finally, to verify the model, we implement it in Verilog-A and simulate the transient response of an inverter and a ring oscillator circuit. Simulation results are in good agreement with the measurement data of fabricated devices.
Electrolyte-gated, printed field-effect transistors exhibit high charge carrier densities in the channel and thus high on-currents at low operating voltages, allowing for the low-power operation of such devices. This behavior is due to the high area-specific capacitance of the device, in which the electrolyte takes the role of the dielectric layer of classical architectures. In this paper, we investigate intrinsic double-layer capacitances of ink-jet printed electrolyte-gated inorganic field-effect transistors in both in-plane and top-gate architectures by means of voltage-dependent impedance spectroscopy. By comparison with deembedding structures, we separate the intrinsic properties of the double-layer capacitance at the transistor channel from parasitic effects and deduce accurate estimates for the double-layer capacitance based on an equivalent circuit fitting. Based on these results, we have performed simulations of the electrolyte cutoff frequency as a function of electrolyte and gate resistances, showing that the top-gate architecture has the potential to reach the kilohertz regime with proper optimization of materials and printing process. Our findings additionally enable accurate modeling of the frequency-dependent capacitance of electrolyte/ion gel-gated devices as required in the small-signal analysis in the circuit simulation.
Rectifiersare vital electronic circuits for signal and power conversion in various smart sensor applications. The ability to process low input voltage levels, for example, from vibrational energy harvesters is a major challenge with existing passive rectifiers in printed electronics, stemming mainly from the built-in potential of the diode's p-njunction. To address this problem, in this work, we design, fabricate, and characterize an inkjet-printed full-wave rectifier using diode-connected electrolyte-gated thin-film transistors (EGTs). Using both experimental and simulation approaches, we investigate how the rectifier can benefit from the near-zero threshold voltage of transistors, which can be enabled by proper channel geometry setting in EGT technology. The presented circuit can be operated at 1-V input voltage, featuring a remarkably small voltage loss of 140 mV and a cutoff frequency of ~300 Hz. Below the cutoff frequency, more than 2.6-μW dc power is obtained over the load resistances ranging from 5 to 20 kQ. Furthermore, experiments show that the circuit can work with an input amplitude down to 500 mV. This feature makes the presented design highly suitable for a variety of energy-harvesting applications.
A versatile liquid metal (LM) printing process enabling the fabrication of various fully printed devices such as intra- and interconnect wires, resistors, diodes, transistors, and basic circuit elements such as inverters which are process compatible with other digital printing and thin film structuring methods for integration is presented. For this, a glass capillary-based direct-write method for printing LMs such as eutectic gallium alloys, exploring the potential for fully printed LM-enabled devices is demonstrated. Examples for successful device fabrication include resistors, p–n diodes, and field effect transistors. The device functionality and easiness of one integrated fabrication flow shows that the potential of LM printing is far exceeding the use of interconnecting conventional electronic devices in printed electronics.
In this study, a facile method to fabricate a cohesive ion‐gel based gate insulator for electrolyte‐gated transistors is introduced. The adhesive and flexible ion‐gel can be laminated easily on the semiconducting channel and electrode manually by hand. The ion‐gel is synthesized by a straightforward technique without complex procedures and shows a remarkable ionic conductivity of 4.8 mS cm−1 at room temperature. When used as a gate insulator in electrolyte‐gated transistors (EGTs), an on/off current ratio of 2.24×104 and a subthreshold swing of 117 mV dec−1 can be achieved. This performance is roughly equivalent to that of ink drop‐casted ion‐gels in electrolyte‐gated transistors, indicating that the film‐attachment method might represent a valuable alternative to ink drop‐casting for the fabrication of gate insulators.
High-performance Ag–Se-based n-type printed thermoelectric (TE) materials suitable for room-temperature applications have been developed through a new and facile synthesis approach. A high magnitude of the Seebeck coefficient up to 220 μV K–1 and a TE power factor larger than 500 μW m–1 K–2 for an n-type printed film are achieved. A high figure-of-merit ZT ∼0.6 for a printed material has been found in the film with a low in-plane thermal conductivity κF of ∼0.30 W m–1 K–1. Using this material for n-type legs, a flexible folded TE generator (flexTEG) of 13 thermocouples has been fabricated. The open-circuit voltage of the flexTEG for temperature differences of ΔT = 30 and 110 K is found to be 71.1 and 181.4 mV, respectively. Consequently, very high maximum output power densities pmax of 6.6 and 321 μW cm–2 are estimated for the temperature difference of ΔT = 30 K and ΔT = 110 K, respectively. The flexTEG has been demonstrated by wearing it on the lower wrist, which resulted in an output voltage of ∼72.2 mV for ΔT ≈ 30 K. Our results pave the way for widespread use in wearable devices.
In this report, we have studied field-effect transistors (FETs) using low-density alumina for electrolytic gating. Device layers have been prepared starting from the structured ITO glasses by printing the In 2 O 3 channels, low-temperature atomic layer deposition (ALD) of alumina (Al 2 O 3 ), and printing graphene top gates. The transistor performance could be deliberately changed by alternating the ambient humidity; furthermore, ID,ON/ID,OFF-ratios of up to seven orders of magnitude and threshold voltages between 0.66 and 0.43 V, decreasing with an increasing relative humidity between 40% and 90%, could be achieved. In contrast to the common usage of Al 2 O 3 as the dielectric in the FETs, our devices show electrolyte-typegating behavior. This is a result from the formation of protons on the Al 2 O 3 surfaces at higher humidities. Due to the very high local capacitances of the Helmholtz double layers at the channel surfaces, the operation voltage can be as low as 1 V. At low humidities (≤30%), the solid electrolyte dries out and the performance breaks down; however, it can fully reversibly be regained upon a humidity increase. Using ALD-derived alumina as solid electrolyte gating material, thus, allows low-voltage operation and provides a chemically stable gating material while maintaining low process temperatures. However, it has proven to be highly humidity-dependent in its performance.
Printed systems spark immense interest in industry, and for several parts such as solar cells or radio frequency identification antennas, printed products are already available on the market. This has led to intense research; however, printed field-effect transistors (FETs) and logics derived thereof still have not been sufficiently developed to be adapted by industry. Among others, one of the reasons for this is the lack of control of the threshold voltage during production. In this work, we show an approach to adjust the threshold voltage (Vth) in printed electrolyte-gated FETs (EGFETs) with high accuracy by doping indium-oxide semiconducting channels with chromium. Despite high doping concentrations achieved by a wet chemical process during precursor ink preparation, good on/off-ratios of more than five orders of magnitude could be demonstrated. The synthesis process is simple, inexpensive, and easily scalable and leads to depletion-mode EGFETs, which are fully functional at operation potentials below 2 V and allows us to increase Vth by approximately 0.5 V.
Printed Electronics technology is a key-enabler for smart sensors, soft robotics, and wearables. The inkjet printed electrolyte-gated field effect transistor (EGFET) technology is a promising candidate for such applications due to its low-power operation, high field-effect mobility, and on-demand fabrication. Unlike conventional silicon-based technologies, inkjet printed electronics technology is an additive manufacturing process where multiple layers are printed on top of each other to realize functional devices such as transistors and their interconnections. Due to the additive manufacturing process, the technology has limited routing layers. For routing of complex circuits, insulating crossovers are printed at the intersection of routing paths to isolate them. The crossover can alter the electrical properties of a circuit based on specific location on a routing path. In this work, we propose a crossover-aware placement and routing (COPnR) methodology for inkjet-printed circuits by integrating the crossover constraints in our design framework. Our proposed placement methodology is based on a state-of-the-art evolutionary algorithm while the routing optimization is done using a genetic algorithm. The proposed methodology is compared with the industrial standard placement and routing (PnR) tools. On average, the proposed methodology has 38% fewer crossovers and 94% fewer failing paths compared to the industrial PnR tools applied to printed circuit designs.
Printed Electronics is perceived to have a major impact in the fields of smart sensors, Internet of Things and wearables. Especially low power printed technologies such as electrolyte gated field effect transistors (EGFETs) using solution-processed inorganic materials and inkjet printing are very promising in such application domains. In this paper, we discuss a modeling approach to describe the variations of printed devices. Incorporating these models and design flows into our previously developed printed design system allows for robust circuit design. Additionally, we propose a reliability-aware routing solution for printed electronics technology based on the technology constraints in printing crossovers. The proposed methodology was validated on multiple benchmark circuits and can be easily integrated with the design automation tools-set.