Refine
Year of publication
- 2015 (19) (remove)
Document Type
- Conference Proceeding (8)
- Article (unreviewed) (6)
- Article (reviewed) (4)
- Part of a Book (1)
Conference Type
- Konferenzartikel (7)
- Sonstiges (1)
Language
- English (19) (remove)
Has Fulltext
- no (19)
Is part of the Bibliography
- yes (19) (remove)
Keywords
- Applikation (2)
- Ausbildung (2)
- Kommunikation (2)
- Produktion (2)
- Sicherheit (2)
- Afrika (1)
- Akustik (1)
- Außenhandel (1)
- Breitbandkommunikation (1)
- CAAD (1)
Institute
- Fakultät Wirtschaft (W) (19) (remove)
Open Access
- Closed Access (7)
- Open Access (3)
The demand of wireless solutions in industrial applications increases since the early nineties. This trend is not only ongoing, it is further pushed by developments in the area of software stacks like the latest Bluetooth Low Energy Stack. It is also pushed by new chip-designs and powerful and highly integrated electronic hardware. The acceptance of wireless technologies as a possible solution for industrial applications, has overcome the entry barrier [1]. The first step to see wireless as standard for many industrial applications is almost accomplished. Nevertheless there is nearly none acceptance of wireless technology for Safety applications. One highly challenging and demanding requirement is still unsolved: The aspect safety and robustness. Those topics have been addressed in many cases but always in a similar manner. WirelessHART as an example addresses this topic with redundant so called multiple propagation paths and frequency hopping to handle with interferences and loss of network participants. So far the pure peer to peer link is rarely investigated and there are less safety solutions available. One product called LoRa™ can be seen as one possible solution to address this lack of safety within wireless links. This paper focuses on the safety performance evaluation of a modem-chip-design. The use of diverse and redundant wireless technologies like LoRa can lead to an increase acceptance of wireless in safety applications. Many measurements in real industrial application have been carried out to be able to benchmark the new chip in terms of the safety aspects. The content of this research results can help to raise the level of confidence in wireless. In this paper, the term “safety” is used for data transmission reliability.
Additive Manufacturing and Reverse Engineering have increasingly been gaining in importance over the past years. This paper investigates the current status of the implementation of these new technologies in design education and also identifies current shortcomings. Then it develops two new approaches for the teaching of the necessary expertise for the design of 3D-printed components and illustrates these with case studies. First, a workshop is presented in which students gain a broad understanding for the functionalities of additive manufacturing and the creative possibilities and limits of this process, through the assembly and installation of a 3D-printer. A second new approach is the combination of reverse engineering and 3D-printing. Thereby, students learn how to deal with this complex process chain. The result of these new approaches can e.g. be seen in the design guidelines for Additive Manufacturing, which were developed by the students themselves. At the same time, the students are able to estimate opportunities and limits of both technologies. Finally, the success of the new course contents and form is reviewed by an evaluation by the students.
This paper presents a new approach for the teaching of competence in additive manufacturing to engineering students in product development. Particularly new to this approach is the combination of the students' autonomous assembly and commissioning of a 3D-printer, and the independent development of guidelines for this new technology regarding the design of components. This way the students will be able to gain first practical experiences with the data preparation, the additive manufacturing process itself and also the required post-treatment of the 3D-printed parts. To allow the students a significantly deeper insight into the functioning of 3D-printing, the workshop Rapid Prototyping developed a new approach in the course of which the students first assemble a construction kit for a 3D-printer themselves and then commission the printer. This enables the students to gain a better understanding of the functionality and configuration of additive manufacturing. In a next step, the students used the 3D-printers they constructed themselves to produce components which they take from a database. Finally, the experiences of the students in the course of the workshop will be evaluated to review the effectiveness of the new approach.
Rubber materials are characterized by a variety of inelasticities such as softening behavior, hysteresis loops and permanent set. In order to calculate the inelastic material behavior, constitutive models, that describe rubber as a homogeneous continuum, have to make use of damping or friction elements.
On the nanoscale, there is no need to adopt such rheological models. Inelastic material behavior can be explained and simulated by a continuous rearrangement of bonds, in particular, the van der Waals interactions, and by the polymer chains transitioning between cis and trans equilibrium torsion angles. The discrete molecular dynamics simulations presented in this paper are performed in an explicit FEM environment using nonlinear but elastic force field potentials. From a structural mechanics point of view, topological changes of the polymer network can be interpreted as a sequence of local material instability problems due to negative tangential bond stiffnesses.
In order to obtain representative results within reasonable computational time, the model is optimized with respect to the number of atoms and the loading velocity. It is shown that by increasing the model size, the stress–strain curves become independent of both the atoms initial state and the strain amplitudes.
Application of Polymer Plaster Composites in Additive Manufacturing of High-Strength Components
(2015)
Today, 3D-printing with polymer plaster composites is a common method in Additive Manufacturing. This technique has proven to be especially suitable for the production of presentation models, due to the low cost of materials and the possibility to produce color-models. But nowadays it requires refinishing through the manual application of a layer of resin. However, the strength of these printed components is very limited, as the applied resin only penetrates a thin edge layer on the surface. This paper develops a new infiltration technique that allows for a significant increase in the strength of the 3D-printed component. For this process, the components are first dehydrated in a controlled two-tier procedure, before they are then penetrated with high-strength resin. The infiltrate used in this process differs significantly from materials traditionally used for infiltration. The result is an almost complete penetration of the components with high-strength infiltrate. As the whole process is computer-integrated, the results are also easier to reproduce, compared to manual infiltration. On the basis of extensive material testing with different testing specimen and testing methods, it can be demonstrated that a significant increase in strength and hardness can be achieved. Finally, this paper also considers the cost and energy consumption of this new infiltration method. As a result of this new technology, the scope of applicability of 3D-printing can be extended to cases that require significantly more strength, like the production of tools for the shaping of metals or used for the molding of plastics. Furthermore, both the process itself and the parameters used are monitored and can be optimized to individual requirements and different fields of application.
Creating growth through trade is an important part of the policy approach of many economies. For decades, many member countries of the Organisation for Economic Co-operation and Development (OECD) have cooperated in a fair competition for the benefit of their national exporters. The countries’ official export credit agencies (ECAs) have established and jointly improved rules and regulations for export credit and political risk insurance. However, new players such as China, Russia or other fast developing countries have now joined the list of top exporting nations. As these countries have established their own ECAs, there is a need to introduce rules and regulations on global standards for financial terms as well as truly international norms ensuring ‘ethical’ trading behaviour.
But how will government support for foreign trade look like in the future? Will global standards for export credit and political risk insurance become reality by 2020? And how will strict rules and regulations for officially supported export credits and FDI regarding ethics, human rights and the environment impact growth through trade in general, or exporters in particular? These are questions addressed by the thirty eight contributions to Global Policy’s third eBook entitled ‘The Future of Foreign Trade Support – Setting Global Standards for Export Credit and Political Risk Insurance’, guest edited by Andreas Klasen and Fiona Bannert.