Refine
Year of publication
Document Type
- Conference Proceeding (11)
- Article (reviewed) (4)
- Patent (2)
- Article (unreviewed) (1)
Conference Type
- Konferenzartikel (9)
- Konferenz-Abstract (2)
Is part of the Bibliography
- yes (18)
Keywords
- Finite-Elemente-Methode (3)
- Nonlinearity (3)
- Substrates (2)
- Surface Acoustic Waves (2)
- Ultraschall (2)
- AlScN (1)
- Equations (1)
- Finite Elemant Method (1)
- Finite Element Method (1)
- Finite element analysis (1)
Institute
Open Access
- Closed (6)
- Closed Access (5)
- Open Access (4)
- Gold (2)
- Bronze (1)
Laser ultrasound was used to determine dispersion curves of surface acoustic waves on a Si (001) surface covered by AlScN films with a scandium content between 0 and 41%. By including off-symmetry directions for wavevectors, all five independent elastic constants of the film were extracted from the measurements. Results for their dependence on the Sc content are presented and compared to corresponding data in the literature, obtained by alternative experimental methods or by ab-initio calculations.
In the framework of electro-elasticity theory and the finite element method (FEM), a model is set up for the computation of quantities in surface acoustic wave (SAW) devices accounting for nonlinear effects. These include second-order and third-order intermodulations, second and third harmonic generation and the influence of electro-acoustic nonlinearity on the frequency characteristics of SAW resonators. The model is based on perturbation theory, and requires input material constants, e.g., the elastic moduli up to fourth order for all materials involved. The model is two-dimensional, corresponding to an infinite aperture, but all three Cartesian components of the displacement and electrical fields are accounted for. The first version of the model pertains to an infinite periodic arrangement of electrodes. It is subsequently generalized to systems with a finite number of electrodes. For the latter version, a recursive algorithm is presented which is related to the cascading scheme of Plessky and Koskela and strongly reduces computation time and memory requirements. The model is applied to TC-SAW systems with copper electrodes buried in an oxide film on a LiNbO3 substrate. Results of computations are presented for the electrical current due to third-order intermodulations and the displacement field associated with the second harmonic and second-order intermodulations, generated by monochromatic input tones. The scope of this review is limited to methodological aspects with the goal to enable calculations of nonlinear quantities in SAW devices on inexpensive and easily accessible computing platforms.
A simple model is introduced that describes the interaction of surface acoustic waves (SAWs) with a 2D periodic array of objects on the surface that give rise to internal resonances. Such objects may be high-aspect ratio structures like micro-pillars fabricated of a material different from that of the substrate. The model allows for an approximate determination of the band structure for the acoustic modes in such systems. Results are presented for the dependence on structural parameters of a total bandgap in the non-radiative regime of a semi-infinite substrate, and it is shown how the frequency and radiation damping of vibrational modes can be determined that are associated with defects in the periodic 2D array.
Recently a P-matrix and COM formalism was presented, which predicts third order intermodulation (IMD3) and triple beat with good accuracy and needs only a single nonlinearity constant. This formalism describes frequency dependence correctly. In this work the dependence of this nonlinearity constant on metalization ratio is investigated for aluminum metalization on LiTaO 3 (YXl)/42°. By comparison to test devices the nonlinearity constant is shown to be largely independent of metalization ratio. The nonlinear effect, however, strongly depends on metalization ratio, which is well described by the model. The linearity of a duplexer is optimized by reduction of metalization ratio and redesign of Tx branch topology.
In this work the nonlinear behavior of layered surface acoustic wave (SAW) resonators is studied with the help of finite element (FE) computations. The full calculations depend strongly on the availability of accurate tensor data. While there are accurate material data for linear computations, the complete sets of higher-order material constants, needed for nonlinear simulations, are still not available for relevant materials. To overcome this problem, scaling factors were used for each available nonlinear tensor. The approach here considers piezoelectricity, dielectricity, electrostriction, and elasticity constants up to the fourth order. These factors act as a phenomenological estimate for incomplete tensor data. Since no set of fourth-order material constants for LiTaO3 is available, an isotropic approximation for the fourth-order elastic constants was applied. As a result, it was found that the fourth-order elastic tensor is dominated by one-fourth order Lamé constant. With the help of the FE model, derived in two different, but equivalent ways, we investigate the nonlinear behavior of a SAW resonator with a layered material stack. The focus was set to third-order nonlinearity. Accordingly, the modeling approach is validated using measurements of third-order effects in test resonators. In addition, the acoustic field distribution is analyzed.
In a SAW device comprises a SAW chip bearing a SAW transducer arranged within a first signal line parasitic signals due to higher harmonics of the operating frequency of the SAW devices are electrically eliminated by compensating means comprising at least one second signal line having means for producing a cancelling signal different in sign or phase to the parasitic signal, or a shunt line to electrically connect the SAW transducer to a back side metallization of the SAW chip.
In einer SAW-Vorrichtung, welche einen SAW-Chip umfasst, der einen SAW-Wandler aufweist, welcher innerhalb einer ersten Signalleitung angeordnet ist, werden Parasitärsignale infolge höherer Harmonischer der Betriebsfrequenz der SAW-Vorrichtungen durch Kompensationsmittel elektrisch beseitigt, welche zumindest eine zweite Signalleitung mit Mitteln zum Erzeugen eines Aufhebungssignals, das im Vorzeichen oder in der Phase vom Parasitärsignal verschieden ist, oder eine Nebenschlussleitung zum elektrischen Verbinden des SAW-Wandlers mit einer rückseitigen Metallisierung des SAW-Chips umfassen.
A Nonlinear FEM Model to Calculate Third-Order Harmonic and Intermodulation in TC-SAW Devices
(2018)
Nonlinearities in Temperature Compensated SAW (TC-SAW) devices in the 2 GHz range are investigated using a nonlinear finite element model by simultaneously considering both third-order intermodulation distortion (IMD3)and third harmonic (H3). In the employed perturbation approach, different contributions to the total H3, the direct and indirect contribution, are discussed. H3 and IMD3 measurements were fitted simultaneously using scaling factors for SiO 2 film and Cu electrode nonlinear material tensors in TC-SAW devices. We employ a P-Matrix simulation as intermediate step: Firstly, measurement and nonlinear P-Matrix calculations for finite devices are compared and coefficients of the P-Matrix simulation are determined. The nonlinear tensor data of the different materials involved in periodic nonlinear finite element method (FEM) computations are optimized to fit periodic P-Matrix calculations by introducing scaling factors. Thus, the contribution of different materials to the nonlinear behavior of TC-SAW devices is obtained and the role of materials is discussed.