Refine
Year of publication
Document Type
- Conference Proceeding (11)
- Article (reviewed) (6)
- Patent (2)
- Part of a Book (1)
- Article (unreviewed) (1)
Conference Type
- Konferenzartikel (9)
- Konferenz-Abstract (2)
Is part of the Bibliography
- yes (21)
Keywords
- Finite-Elemente-Methode (3)
- Nonlinearity (3)
- Substrates (2)
- Surface Acoustic Waves (2)
- Ultraschall (2)
- AlScN (1)
- Equations (1)
- Finite Elemant Method (1)
- Finite Element Method (1)
- Finite element analysis (1)
Institute
Open Access
- Closed Access (8)
- Closed (6)
- Open Access (4)
- Gold (2)
- Bronze (1)
Propagation of acoustic waves is considered in a system consisting of two stiff quarter-spaces connected by a planar soft layer. The two quarter-spaces and the layer form a half-space with a planar surface. In a numerical study, surface waves have been found and analyzed in this system with displacements that are localized not only at the surface, but also in the soft layer. In addition to the semi-analytical finite element method, an alternative approach based on an expansion of the displacement field in a double series of Laguerre functions and Legendre polynomials has been applied.
It is shown that a number of branches of the mode spectrum can be interpreted and remarkably well described by perturbation theory, where the zero-order modes are the wedge waves guided at a rectangular edge of the stiff quarter-spaces or waves guided at the edge of a soft plate with rigid surfaces.
For elastic moduli and densities corresponding to the material combination PMMA–silicone–PMMA, at least one of the branches in the dispersion relation of surface waves trapped in the soft layer exhibits a zero-group velocity point.
Potential applications of these 1D guided surface waves in non-destructive evaluation are discussed.
In einer SAW-Vorrichtung, welche einen SAW-Chip umfasst, der einen SAW-Wandler aufweist, welcher innerhalb einer ersten Signalleitung angeordnet ist, werden Parasitärsignale infolge höherer Harmonischer der Betriebsfrequenz der SAW-Vorrichtungen durch Kompensationsmittel elektrisch beseitigt, welche zumindest eine zweite Signalleitung mit Mitteln zum Erzeugen eines Aufhebungssignals, das im Vorzeichen oder in der Phase vom Parasitärsignal verschieden ist, oder eine Nebenschlussleitung zum elektrischen Verbinden des SAW-Wandlers mit einer rückseitigen Metallisierung des SAW-Chips umfassen.
In a SAW device comprises a SAW chip bearing a SAW transducer arranged within a first signal line parasitic signals due to higher harmonics of the operating frequency of the SAW devices are electrically eliminated by compensating means comprising at least one second signal line having means for producing a cancelling signal different in sign or phase to the parasitic signal, or a shunt line to electrically connect the SAW transducer to a back side metallization of the SAW chip.
The growing complexity in RF front-ends, which support carrier aggregation and a growing number of frequency bands, leads to tightened nonlinearity requirements in all sub-components. The generation of third order intermodulation products (IMD3) are typical problems caused by the non-linearity of SAW devices. In the present work, we investigate temperature compensating (TC) SAW devices on Lithium Niobate-rot128YX. An accurate FEM simulation model [1] is employed, which allows to better understand the origin of nonlinearities in such acoustic devices.
In the present work, nonlinearities in temperature compensating (TC) SAW devices are investigated. The materials used are LiNbO₃-rot128YX as the substrate and Copper electrodes covered with a SiO₂-layer as the compensating layer. In order to understand the role of these materials for the nonlinearities in such acoustic devices, a FEM simulation model in combination with a perturbation approach is applied. The nonlinear tensor data of the different materials involved in TC-SAW devices have been taken from literature, but were partially modified to fit experimental data by introducing scaling factors. An effective nonlinearity constant is determined by comparison of nonlinear P-matrix simulations to IMD3 measurements of test filters. By employing these constants in nonlinear periodic P-matrix simulations a direct comparison to nonlinear periodic FEM-simulations yields the scaling factors for the material used. Thus, the contribution of different materials to the nonlinear behavior of TC-SAW devices is obtained and the role of metal electrodes is discussed in detail.
In this work a set of nonlinear coupled COM equations at interacting frequencies is derived on the basis of nonlinear electro-elasticity. The formalism is presented with the aim of describing intermodulation distortion of third-order (IMD3) and triple beat. The resulting COM equations are translated to the P-matrix formalism, where care is taken to obtain the correct frequency dependence. The scheme depends on two frequency-independent constants for an effective third-order nonlinearity. One of these two constants is negligibly small in the systems considered here. The P-matrix approach is applied to single filters and duplexers on LiTaO 3 (YXl)/42° operating in different frequency ranges. Both IMD3 and triple beat show good agreement with measurement.
In this work the nonlinear behavior of layered surface acoustic wave (SAW) resonators is studied with the help of finite element (FE) computations. The full calculations depend strongly on the availability of accurate tensor data. While there are accurate material data for linear computations, the complete sets of higher-order material constants, needed for nonlinear simulations, are still not available for relevant materials. To overcome this problem, scaling factors were used for each available nonlinear tensor. The approach here considers piezoelectricity, dielectricity, electrostriction, and elasticity constants up to the fourth order. These factors act as a phenomenological estimate for incomplete tensor data. Since no set of fourth-order material constants for LiTaO3 is available, an isotropic approximation for the fourth-order elastic constants was applied. As a result, it was found that the fourth-order elastic tensor is dominated by one-fourth order Lamé constant. With the help of the FE model, derived in two different, but equivalent ways, we investigate the nonlinear behavior of a SAW resonator with a layered material stack. The focus was set to third-order nonlinearity. Accordingly, the modeling approach is validated using measurements of third-order effects in test resonators. In addition, the acoustic field distribution is analyzed.
Among the various types of guided acoustic waves, acoustic wedge waves are non-diffractive and non-dispersive. Both properties make them susceptible to nonlinear effects. Investigations have recently been focused on effects of second-order nonlinearity in connection with anisotropy. The current status of these investigations is reviewed in the context of earlier work on nonlinear properties of two-dimensional guided acoustic waves, in particular surface waves. The role of weak dispersion, leading to solitary waves, is also discussed. For anti-symmetric flexural wedge waves propagating in isotropic media or in anisotropic media with reflection symmetry with respect to the wedge’s mid-plane, an evolution equation is derived that accounts for an effective third-order nonlinearity of acoustic wedge waves. For the kernel functions occurring in the nonlinear terms of this equation, expressions in terms of overlap integrals with Laguerre functions are provided, which allow for their quantitative numerical evaluation. First numerical results for the efficiency of third-harmonic generation of flexural wedge waves are presented.
The laser ultrasound (LU) technique has been used to determine dispersion curves for surface acoustic waves (SAW) propagating in AlScN/Al2O3 systems. Polar and non-polar Al0.77Sc0.23N thin films were prepared by magnetron sputter epitaxy on Al2O3 substrates and coated with a metal layer. SAW dispersion curves have been measured for various propagation directions on the surface. This is easily achieved in LU measurements since no additional surface structures need to be fabricated, which would be required if elastic properties are determined with the help of SAW resonators. Variation of the propagation direction allows for efficient use of the system’s anisotropy when extracting information on elastic properties. This helps to overcome the complexity caused by a large number of elastic constants in the film material. An analysis of the sensitivity of the SAW phase velocities (with respect to the elastic moduli and their dependence on SAW propagation direction) reveals that the non-polar AlScN films are particularly well suited for the extraction of elastic film properties. Good agreement is found between experiment and theoretical predictions, validating LU as a non-destructive and fast technique for the determination of elastic constants of piezoelectric thin films.